| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix heap overflow in DACL owner/group rewrite
When id_mode_to_cifs_acl rewrites an existing DACL, it allocates a
buffer sized according to the on-disk DACL length reported by
dacl_ptr->size. However, replace_sids_and_copy_aces may rewrite each
ACE with a new owner/group SID obtained from the cifs.idmap upcall.
Those SIDs can have up to SID_MAX_SUB_AUTHORITIES (15) sub-authorities,
making each ACE up to 76 bytes (sizeof(struct smb_ace)).
If the original DACL contains short SIDs (e.g., 1 sub-authority) while
the replacement SIDs are long, the rewritten ACEs overflow the
allocation.
Fix this by always budgeting for worst-case SID expansion: allocate
sizeof(struct smb_acl) plus num_aces * sizeof(struct smb_ace), which
covers the smb_acl header and room for every ACE at maximum SID size.
This replaces the previous split logic that used dacl_ptr->size for
cifsacl mounts but num_aces * sizeof(struct smb_ace) for mode_from_sid
mounts: both paths can trigger the same rewrite and need the same
headroom.
KASAN reports this as:
BUG: KASAN: slab-out-of-bounds in build_sec_desc+0x1e8a/0x2680 [cifs]
Write of size 4 at addr ffff8881a5e25374 by task chown/5298
...
The buggy address is located 0 bytes to the right of
allocated 884-byte region [ffff8881a5e25000, ffff8881a5e25374) |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: avoid leaking refcount when cifs_sb_tlink() fails
cifs_oplock_break() takes over the reference that
cifs_queue_oplock_break() acquired when it queued the work, and drops it
with _cifsFileInfo_put() once the break has been processed.
Only in setups with "-o multiuser", cifs_sb_tlink() may fail, at which
point cifs_oplock_break() returns without putting the file reference,
mirroring the reference leak we already fixed in the companion patch to
cifs_queue_oplock_break().
This would trigger a crash due to busy inodes on the next unmount:
BUG: Dentry ... still in use (1) [unmount of cifs cifs]
VFS: Busy inodes after unmount of cifs (cifs)
Drop the reference on that path as well. Doing so before the out label
mirrors the normal path, which also puts the reference before
cifs_done_oplock_break().
Found by Sashiko code review. The failure path was not exercised at
runtime. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix one-byte OOB read in smb2_parse_native_symlink()
When parsing a share-root relative native symlink, memcpy copies
smb_target+1 (skipping the leading separator) but uses
strlen(smb_target)+1 as the length, reading one byte past the
allocated buffer.
This fixes the following KASAN splat when accessing an SMB symlink
with a target of '\a\b':
BUG: KASAN: slab-out-of-bounds in smb2_parse_native_symlink+0x4f5/0xca0
Read of size 5 at addr ffff88800878fe21 by task netfsfuzz-execu/1
CPU: 1 UID: 0 PID: 1 Comm: netfsfuzz-execu Tainted: G N
7.2.0-11943-g2709dd5ae32f-dirty #1 PREEMPT(lazy)
Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix,
1996)
Call Trace:
<TASK>
dump_stack_lvl+0x7b/0xa0
print_report+0xd0/0x630
kasan_report+0xe5/0x120
kasan_check_range+0x105/0x1b0
__asan_memcpy+0x23/0x60
smb2_parse_native_symlink+0x4f5/0xca0
parse_reparse_point+0x68a/0x1530
reparse_info_to_fattr+0x752/0xa20
cifs_get_fattr+0x873/0x15b0
cifs_get_inode_info+0xc0/0x310
cifs_lookup+0x308/0xa70
__lookup_slow+0x122/0x2b0
lookup_slow+0x50/0x70
path_lookupat+0x525/0xaf0
filename_lookup+0x1f2/0x550
vfs_statx+0xd1/0x1a0
vfs_fstatat+0x65/0xc0
__do_sys_newfstatat+0x9a/0x120
do_syscall_64+0xdd/0x4a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: pm: kernel: drop pending ADD_ADDR when removing ID0
The in-kernel MPTCP path manager can leave a stale ADD_ADDR announcement
entry alive when removing the id 0 endpoint. This happens because the id 0
removal path does not tear down pending announcements, unlike the non-zero
id path.
When the PM later reselects id 0 after adding another signal endpoint, it
finds the stale anno_list entry and hits WARN_ON_ONCE(mptcp_pm_is_kernel())
in mptcp_pm_announced_alloc().
Root cause: asymmetry between removal paths.
- Non-zero id path: mptcp_nl_remove_subflow_and_signal_addr() calls
mptcp_pm_remove_announced() to clean up.
- Id 0 path: mptcp_nl_remove_id_zero_address() skips cleanup entirely.
Fix by making the id 0 path symmetric: call mptcp_pm_announced_remove()
and decrement add_addr_signaled before queuing the RM_ADDR.
Subtle detail: signal endpoints are stored in anno_list with port 0, but
msk_local carries the connection's local port. In other words, entries
linked to ID0 paths should have port == 0. A follow-up patch will ensure
that. mptcp_pm_announced_remove() uses use_port=true for comparison. So
clear the port before the lookup. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: syncookies: remember the request backup flag
Instead of using an uninitialised bit when copying the info in
subflow_ulp_clone().
To fix this, no need to extend the join_entry structure: backup is
coming from struct mptcp_subflow_request_sock, only one bit. Do the same
here by using one bit for both. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Propagate TPA buffer allocation failures in bnxt_queue_mem_alloc()
bnxt_alloc_one_tpa_info_data() returns -ENOMEM as soon as one allocation
fails. This leaves the remaining rxr->rx_tpa[] entries zeroed.
bnxt_queue_mem_alloc() discards that return value, so the partially
initialized ring is installed by bnxt_queue_start().
Since the agg_id is picked by the hardware and bnxt_alloc_agg_idx maps
it to a SW index in rxr->rx_tpa[], it is possible that an uninitialized
slot can be chosen which would hand a zero DMA address to the device.
Fix this by checking the return value of bnxt_alloc_one_tpa_info_data
and unwinding, freeing the ring buffers. |
| In the Linux kernel, the following vulnerability has been resolved:
net: net_failover: Fix the deadlock in net_failover_slave_name_change()
This is a sibling fix of commit
b84c5632c7b3 ("net: net_failover: Fix the deadlock in slave register").
There is netdev_lock_ops() in the upper callers, so using netif_open()
instead of dev_open().
Call Trace:
__schedule+0x2bb/0x650
schedule+0x27/0xb0
schedule_preempt_disabled+0x15/0x30
__mutex_lock.constprop.0+0x550/0xaf0
__mutex_lock_slowpath+0x13/0x20
mutex_lock+0x3b/0x50
dev_open+0x3b/0xe0
net_failover_slave_name_change+0x22/0x40
failover_event+0xd4/0x1e0
notifier_call_chain+0x62/0xf0
raw_notifier_call_chain+0x16/0x30
call_netdevice_notifiers_info+0x50/0x80
netif_change_name+0x200/0x330
do_setlink.isra.0+0xb12/0xdf0
? security_capable+0x9a/0x1e0
? ns_capable+0x31/0x60
rtnl_setlink+0x302/0x670
? netlink_recvmsg+0x296/0x340
? security_capable+0x9a/0x1e0
? __pfx_rtnl_setlink+0x10/0x10
rtnetlink_rcv_msg+0x384/0x460
? __pfx_rtnetlink_rcv_msg+0x10/0x10
netlink_rcv_skb+0x61/0x120
rtnetlink_rcv+0x15/0x30
netlink_unicast+0x28f/0x3c0
netlink_sendmsg+0x216/0x450
__sys_sendto+0x222/0x230
__x64_sys_sendto+0x24/0x40
x64_sys_call+0x1d5d/0x2390
do_syscall_64+0x105/0x5a0
? do_syscall_64+0x140/0x5a0
? exc_page_fault+0x94/0x1e0
entry_SYSCALL_64_after_hwframe+0x76/0x7e |
| In the Linux kernel, the following vulnerability has been resolved:
net: hinic: fix mailbox segment buffer overflow
check_mbox_seq_id_and_seg_len() validates that seq_id does not
exceed SEQ_ID_MAX_VAL (42) and seg_len does not exceed
MBOX_SEG_LEN (48). However, this allows the last segment
(seq_id=42) to carry a full 48-byte payload, writing to offset
42*48=2016 for 48 bytes (ending at byte 2064). The receive
buffer is only MBOX_MAX_BUF_SZ (2048) bytes, resulting in a
16-byte heap buffer overflow.
The hinic3 driver already handles this correctly by defining
MBOX_LAST_SEG_MAX_LEN and rejecting the last segment when it
exceeds the remaining buffer space. Apply the same fix to the
hinic driver. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel: Prevent drain_pebs() reentry
The PEBS buffer is shared by all events on a CPU, so drain_pebs() must
not be reentered. If so, one instance may observe stale buffer state and
potentially access out-of-bound memory.
Most invocations happen in NMI context, which naturally prevents reentry.
However, drain_pebs() is also reachable from process context via
intel_pmu_drain_pebs_buffer().
In those paths, the PMU is often already disabled, but not guaranteed.
For example, __intel_pmu_pebs_disable() only disables the target counter,
so other active counters can still raise a PMI and interrupt an in-flight
drain_pebs(). Here is an example,
__perf_addr_filters_adjust()
perf_event_stop()
__perf_event_stop()
x86_pmu_stop() (event->pmu->stop)
intel_pmu_disable_event()
intel_pmu_pebs_disable()
__intel_pmu_pebs_disable()
intel_pmu_drain_large_pebs()
intel_pmu_drain_pebs_buffer()
Introduce __intel_pmu_quiesce() and __intel_pmu_resume() helpers and
use them in intel_pmu_drain_large_pebs() to disable the full PMU
around the intel_pmu_drain_pebs_buffer() call, preventing reentry.
Also add a warning in intel_pmu_drain_pebs_buffer() when the full PMU is
not disabled. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Don't free the live ring's TPA state on queue restart failure
bnxt_queue_mem_alloc() shallow copies the live RX ring into the clone:
memcpy(clone, rxr, sizeof(*rxr));
the code currently clears pointers that the clone owns (such as
rx_agg_bmap), but rx_tpa and rx_tpa_idx_map are left pointing at memory
of the live ring that was cloned.
If an allocation failure happens later and the err_free_tpa_info label
is taken, the live ring's memory can be freed while still in use.
Fix this by initializing the clone's pointers to NULL to prevent live
ring state from being freed inadvertently. |
| In the Linux kernel, the following vulnerability has been resolved:
media: v4l2-ctrls: validate HEVC tile counts
The stateless HEVC decoders read num_tile_columns_minus1 + 1 entries from
column_width_minus1[] and num_tile_rows_minus1 + 1 from row_height_minus1[]
and use them as tile-loop bounds, but std_validate_compound() does not
bound these u8 counts. Reject a V4L2_CTRL_TYPE_HEVC_PPS with tiling
enabled whose tile counts exceed the uAPI array capacity, mirroring the
existing compound-control range checks. |
| In the Linux kernel, the following vulnerability has been resolved:
media: verisilicon: rockchip: guard VPU981 AV1 divisor and tile buffer
rockchip_vpu981_av1_dec_set_tile_info() divides context_update_tile_id by
tile_info->tile_cols and writes one descriptor per tile into the tile_info
DMA buffer, which holds AV1_MAX_TILES entries; tile_cols and tile_rows
come from the bitstream. Guard the division against a zero tile_cols by
initialising the context-update values to zero and computing them only
when tile_cols is non-zero, and stop the descriptor writes once the
tile_info buffer is full. The tile geometry written to the hardware
registers is left unmodified; the per-dimension and total tile bounds are
enforced by the control validation. |
| In the Linux kernel, the following vulnerability has been resolved:
media: mediatek: vcodec: bound AV1 tile-start copy to the array capacity
vdec_av1_slice_setup_tile() copies tile_cols + 1 / tile_rows + 1 entries
into mi_col_starts[] / mi_row_starts[] from the bitstream tile_info. Bound
the copy to the array capacity. |
| In the Linux kernel, the following vulnerability has been resolved:
inet: frags: invalidate queues before flushing them
fqdir_pre_exit() flushes the skbs from incomplete queues without
changing their completion state. A fragment which found a queue before
high_thresh was cleared can then acquire the queue lock and reuse stale
reassembly metadata. A queue concurrently killed after fqdir->dead is
set can instead become INET_FRAG_COMPLETE|INET_FRAG_HASH_DEAD while
still holding its old skbs; skipping it because it is complete leaves
those references behind until asynchronous fqdir teardown.
For IPv6, stale metadata can make ip6_frag_reasm() use the old
nhoffset with a new skb and access memory out of bounds. The resulting
heap corruption can be leveraged for local privilege escalation when
unprivileged network namespaces are available. Unflushed fragments can
also keep conntrack references alive after the conntrack per-net
cleanup point.
Kill each incomplete queue, then flush every queue still owned by the
dying rhashtable. HASH_DEAD identifies that ownership, while complete
queues without it are already owned by another destroy path and must be
left alone. Releasing a timer reference removed by inet_frag_kill() is
deferred to inet_frag_putn(), after the queue lock is dropped.
KASAN report:
BUG: KASAN: slab-out-of-bounds in ipv6_frag_rcv (net/ipv6/reassembly.c:289 (discriminator 2) net/ipv6/reassembly.c:229 (discriminator 2) net/ipv6/reassembly.c:391 (discriminator 2))
Write of size 1 at addr ff110001039c6e00 by task poc/771
Call Trace:
? ipv6_frag_rcv (net/ipv6/reassembly.c:289 (discriminator 2) net/ipv6/reassembly.c:229 (discriminator 2) net/ipv6/reassembly.c:391 (discriminator 2))
ipv6_frag_rcv (net/ipv6/reassembly.c:289 (discriminator 2) net/ipv6/reassembly.c:229 (discriminator 2) net/ipv6/reassembly.c:391 (discriminator 2))
ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:479 (discriminator 5))
ip6_input_finish (net/ipv6/ip6_input.c:534)
ipv6_rcv (include/net/dst.h:480 (discriminator 3) net/ipv6/ip6_input.c:119 (discriminator 3) net/ipv6/ip6_input.c:109 (discriminator 3) include/linux/netfilter.h:325 (discriminator 3) include/linux/netfilter.h:319 (discriminator 3) net/ipv6/ip6_input.c:351 (discriminator 3))
packet_sendmsg (net/packet/af_packet.c:3110 net/packet/af_packet.c:3142)
__x64_sys_sendmmsg (net/socket.c:2883 net/socket.c:2880 net/socket.c:2880)
The buggy address belongs to the object at ff110001039c6b40
which belongs to the cache skbuff_small_head of size 704
The buggy address is located 0 bytes to the right of
allocated 704-byte region [ff110001039c6b40, ff110001039c6e00)
BUG: KASAN: slab-out-of-bounds in ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:423 (discriminator 1))
Read of size 1 at addr ff110001039c6e08 by task poc/771
Call Trace:
? ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:423 (discriminator 1))
ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:423 (discriminator 1))
ip6_input_finish (net/ipv6/ip6_input.c:534)
ipv6_rcv (include/net/dst.h:480 (discriminator 3) net/ipv6/ip6_input.c:119 (discriminator 3) net/ipv6/ip6_input.c:109 (discriminator 3) include/linux/netfilter.h:325 (discriminator 3) include/linux/netfilter.h:319 (discriminator 3) net/ipv6/ip6_input.c:351 (discriminator 3))
packet_sendmsg (net/packet/af_packet.c:3110 net/packet/af_packet.c:3142)
__x64_sys_sendmmsg (net/socket.c:2883 net/socket.c:2880 net/socket.c:2880)
packet_sendmsg (net/packet/af_packet.c:2959 net/packet/af_packet.c:3053 net/packet/af_packet.c:3142)
__x64_sys_sendmmsg (net/socket.c:2883 net/socket.c:2880 net/socket.c:2880)
The buggy address belongs to the object at ff110001039c6b40
which belongs to the cache skbuff_small_head of size 704
The buggy address is located 8 bytes to the right of
allocated 704-byte region [ff110001039c6b40, ff110001039c6e00) |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sysfs: Fix NULL pointer dereference in device_del()
A NULL pointer dereference in klist_put() occurs when a child device (such
as a BNEP network device in bnep_session) is concurrently being
unregistered while hci_conn_del_sysfs() reparents child devices.
This is caused by a race condition between hci_conn_del_sysfs() and
concurrent child device unregistration (e.g. bnep_session calling
unregister_netdev()). During device unregistration, device_del() snapshots
a non-NULL parent pointer. Concurrently, hci_conn_del_sysfs() finds the
child device using device_find_any_child() and calls device_move() to
reparent it to NULL, which removes the node from its parent's klist and
clears knode_parent. Subsequently, device_del() calls
klist_del(&dev->p->knode_parent) using the stale parent snapshot, causing
klist_put() to dereference knode_klist(n)->put on an already removed node,
resulting in a NULL pointer dereference.
This race was introduced by commit 27aabf27fd01 ("Bluetooth: fix
use-after-free in device_for_each_child()"), which replaced
device_find_child(..., __match_tty) with device_find_any_child() in
hci_conn_del_sysfs(). That change was intended to avoid a use-after-free
where conn->dev outlived its parent hdev->dev when child devices held
references to conn->dev, because conn->dev only held a reference to
hdev->dev while registered in sysfs.
Fix the issue properly by taking an explicit reference to the parent device
with get_device(&hdev->dev) in hci_conn_init_sysfs() and dropping it with
put_device(parent) in bt_link_release() when the conn device is freed. This
ensures that hdev->dev remains valid for the entire lifecycle of conn->dev,
resolving the underlying use-after-free. With the parent reference held
properly, restore the __match_tty filter in hci_conn_del_sysfs() so that
device_move() is only invoked on persistent RFCOMM TTY devices as
originally intended, eliminating the race condition with unregistering
network devices. |
| A flaw was found in crun. When the container configuration does not give /dev a dedicated mount, terminal setup can redirect /dev/console onto an attacker-controlled path, including via the read-only-rootfs bind-mount fallback. Affected versions are crun 1.29.1 and earlier. Default configurations that mount a fresh /dev are not exposed. No fixed release is available yet. |
| BusyBox passwd/group tokenize() references a stale endpoint pointer after trimming, causing an out-of-bounds write of heap pointers. |
| BusyBox dpkg read_package_field() steps past a NUL terminator on malformed .deb packages, causing an out-of-bounds heap read. |
| BusyBox httpd treats yescrypt ($y$) password hashes as plaintext during Basic Authentication, inverting the authentication check. |
| BusyBox httpd IP deny rules with invalid CIDR prefix lengths fail open, leaving a parsed IP with a zeroed mask so the rule matches no clients. |
