Export limit exceeded: 430256 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.

Search

Search Results (430256 CVEs found)

CVE Vendors Products Updated CVSS v3.1
CVE-2026-99744 1 Linux 2 Linux, Linux Kernel 2026-11-20 N/A
In the Linux kernel, the following vulnerability has been resolved: net: atl1c: drop oversized RX frames instead of panicking atl1c sizes its receive buffers from the netdev MTU plus a fixed set of L2 overheads, which comes to 1522 bytes at the default MTU. A link partner that sends a longer frame - in practice a MikroTik CCR2004-1G-2XS-PCIe, whose RouterOS side defaults to l2mtu 1600 while the host stays at MTU 1500 - makes the length reported by the RX return descriptor exceed what the hardware wrote, and skb_put() then either includes bytes that were never received or trips skb_over_panic and takes the host down. Compare the descriptor length against buffer_info->length, the length the hardware was given, rather than against skb_tailroom(): the skb carries 64 bytes of slack for the DMA erratum, so tailroom is larger than the DMA buffer and a frame in between would pass the check and still be delivered with a tail the device never wrote. The same test rejects frames shorter than ETH_HLEN + ETH_FCS_LEN; before this change a reported length below ETH_FCS_LEN underflowed in skb_put(). The frame is dropped with kfree_skb_reason(SKB_DROP_REASON_PKT_TOO_BIG) so drop_monitor and the kfree_skb tracepoint see it, and counted through dev_core_stats_rx_dropped_inc(), which survives atl1c_get_stats() overwriting the hardware counters on every read. It also counts as work: atl1c_clean_rfd() has already recycled the RFD, and the refill at the end of the poll only runs when work_done is non-zero, so sustained oversized traffic would otherwise drain the ring and stop RX. Tested on a MikroTik CCR2004-1G-2XS-PCIe (4x AR8151) in a Proxmox VE host, with atl1c built from a DKMS tree carrying this change: the l2mtu-1600 traffic that panics the stock driver is dropped and counted with the patch applied, and received normally once the host MTU is raised to match. This complements commit 36c2009d90f2 ("net: atl1c: fix soft lockup on out-of-range tpd_cons read"), which fixed the TX side of the same "host dies while the card resets" problem.
CVE-2026-131018 1 Google 1 Chrome 2026-11-20 8.1 High
Confused deputy in DevTools in Google Chrome prior to 158.0.8127.36 allowed a remote attacker leveraging social engineering to bypass web origin policy via a crafted HTML page. (Chromium security severity: Low)
CVE-2026-133608 1 Openzipkin 1 Zipkin 2026-11-20 5.3 Medium
A vulnerability was identified in OpenZipkin Zipkin 3.6.1. This affects the function UnzippingBytesRequestConverter.convertRequest of the file zipkin-server/src/main/java/zipkin2/server/internal/ZipkinHttpCollector.java of the component HTTP Collector. Such manipulation leads to highly compressed data. The attack can be executed remotely. The pull request to fix this issue awaits acceptance.
CVE-2026-109878 2026-11-20 7.1 High
Improper Neutralization of Input During Web Page Generation ('Cross-site Scripting') vulnerability in Elementor Elementor Website Builder elementor allows Reflected XSS.This issue affects Elementor Website Builder: from n/a through 4.4.0.
CVE-2026-132749 1 Vtiger 1 Vtiger Crm 2026-11-20 6.5 Medium
Vtiger CRM through 8.4.0 contains a blind SQL injection vulnerability in ReportRun::generateAdvFilterSql() that allows authenticated low-privileged users to inject SQL via the bw comparator. Attackers can send a crafted advanced_filter parameter containing a single quote to the Reports getRecordsCount action to break out of BETWEEN literals and extract database contents.
CVE-2026-132745 1 Vtiger 1 Vtiger Crm 2026-11-20 6.5 Medium
Vtiger CRM through 8.4.0 contains a blind SQL injection vulnerability that allows authenticated non-administrative users to inject SQL through the k (does not contain) comparator in list view search_params. Attackers can send crafted search_params to the ListAjax getRecordsCount mode, breaking out of the unescaped NOT LIKE clause to extract database contents via boolean or time-based techniques.
CVE-2026-132602 2 Seo Panel, Seopanel 2 Seo Panel, Seo Panel 2026-11-20 6.3 Medium
A vulnerability was detected in SEO Panel 6.0.0. This impacts an unknown function of the file controllers/siteauditor.ctrl.php of the component Site Auditor. Performing a manipulation of the argument order_col/order_val results in sql injection. The attack can be initiated remotely. The exploit is now public and may be used. Upgrading to version 7.0.0 will fix this issue. The patch is named 389783b5d8235f5637f4e4587f524b5fef07864d. The affected component should be upgraded.
CVE-2026-132610 1 Sourcecodester 1 Simple Form Builder Web App 2026-11-20 7.3 High
A security flaw has been discovered in SourceCodester Simple Form Builder Web App 1.0. The impacted element is the function save_form of the file /classes/Forms.php. Performing a manipulation of the argument form_code/form_data results in code injection. The attack may be initiated remotely. The exploit has been released to the public and may be used for attacks.
CVE-2026-132625 1 Sourcecodester 1 Student Project Allocation And Management System 2026-11-20 7.3 High
A vulnerability was determined in SourceCodester Student Project Allocation and Management System 1.0. Affected is an unknown function of the file /login.php of the component Login Handler. Executing a manipulation of the argument username/password can lead to sql injection. The attack may be performed from remote. The exploit has been publicly disclosed and may be utilized.
CVE-2026-132128 2026-11-20 7.4 High
@fastify/middie is the middleware engine that adds Express and Connect style middleware support to Fastify. In versions up to and including 9.3.6, middie does not honor the router's caseSensitive setting and matches path-scoped middleware mount paths with a case-insensitive regular expression that does not fold non-ASCII characters, while Fastify's router, when caseSensitive is set to false, lowercases the request path with a Unicode-aware conversion that maps the KELVIN SIGN character (U+212A) to the ASCII letter k. A request that spells a k in a protected mount path as the percent-encoded KELVIN SIGN is therefore routed to the protected handler while the middleware mounted on that path, such as authentication, authorization, or rate limiting, never matches and is skipped, letting an unauthenticated client reach the handler. Only applications that set caseSensitive to false and protect a mount path containing the letter k are affected. The issue is fixed in @fastify/middie 9.3.7, and users should upgrade to 9.3.7 or later. As a workaround, enforce authorization in a Fastify hook such as preHandler that runs after routing, or keep routing case-sensitive, which is the default.
CVE-2026-132133 2026-11-20 4.8 Medium
@fastify/middie is the middleware engine that adds Express and Connect style middleware support to Fastify. In versions up to and including 9.3.6, middie builds the match regular expression for each path-scoped middleware from its mount path without collapsing duplicate slashes, even when the application enables the ignoreDuplicateSlashes router option. Under that option Fastify's router collapses duplicate slashes in both the registered route and the request path, so a mount path containing a doubled slash is served by the router at its single-slash form while the middleware's compiled match still requires the doubled slash and never matches. A path-scoped middleware such as authentication, authorization, or rate limiting is therefore skipped while the router dispatches the request to the protected handler, without any authentication required. Applications are affected when they enable ignoreDuplicateSlashes and a middleware mount path reaches middie with a duplicate slash, most commonly when a plugin prefix that ends with a slash is joined to a mount path that starts with one. The issue is fixed in @fastify/middie 9.3.7, and users should upgrade to 9.3.7 or later. As a workaround, enforce authorization in a Fastify hook such as preHandler that runs after routing, and avoid mount paths and plugin prefixes that introduce duplicate slashes.
CVE-2026-99488 1 Linux 2 Linux, Linux Kernel 2026-11-20 4.1 Medium
In the Linux kernel, the following vulnerability has been resolved: klist: avoid accesses after waking klist_remove() klist_remove() waits until a node is unreferenced so that its caller can free the containing object. klist_release() currently publishes waiter->woken and wakes the waiter before its final accesses to the waiter and node. klist_remove() can then return, allowing its stack waiter and the containing object to be freed or reused while klist_release() is still running. In particular, bus_remove_driver() can free drv->p while __device_attach() walks the same bus klist with bus_for_each_drv(). On an arm64 Cortex-A72 system, an unpatched 7.2.0-rc3 kernel with CONFIG_PREEMPT_RT=y and CONFIG_KASAN=y reproduced the bug through the in-tree I2C/at24 path. KASAN reported a use-after-free in klist_dec_and_del() reached from klist_next()/bus_for_each_drv() while at24 was being unregistered. Clear n_klist and take a task reference before publishing woken. Use release/acquire accesses for that publication and wake the referenced task. The task reference keeps the waiter task alive if it returns and exits before wake_up_process().
CVE-2026-99489 1 Linux 2 Linux, Linux Kernel 2026-11-20 4.6 Medium
In the Linux kernel, the following vulnerability has been resolved: HID: wacom: Redesign shared sibling data lifecycle The Wacom driver coordinates state between sibling interfaces of the same physical device using a shared structure 'wacom_shared' inside 'wacom_hdev_data'. The driver kept a volatile representative pointer 'data->dev' pointing to a sibling 'hid_device' for physical path comparisons during sibling matching. This pointer management is fragile. When the representative device is disconnected, wacom_remove_shared_data() failed to clear/update 'data->dev', leading to a Use-After-Free vulnerability when subsequent sibling probes dereference the dangling 'data->dev' pointer. Resolve this issue by redesigning the sibling data lifecycle: - Eliminate the volatile 'data->dev' representative pointer completely - Redesign 'wacom_hdev_data' to store stable static copies of the required attributes upon first allocation: 'phys' path string, 'vendor', 'product' IDs and the sibling's 'device_type' - Use these static attributes for stable sibling matching in wacom_are_sibling() and wacom_get_hdev_data() This ensures sibling matching remains safe and stable even if individual siblings are dynamically added or removed. To secure the lifecycle against concurrent probe/disconnect races: - Switch kref_put() to kref_put_mutex() in wacom_remove_shared_data() to serialize refcount drops with list traversal and lookup - Modify wacom_release_shared_data() to assume the list lock is already held Also, do not accumulate the 'device_type' capability flag during subsequent sibling probes. Keeping only the first probed sibling's device_type exactly preserves the original sibling matching behavior without introducing side effects.
CVE-2026-99490 1 Linux 2 Linux, Linux Kernel 2026-11-20 7.0 High
In the Linux kernel, the following vulnerability has been resolved: HID: wacom: Fix Use-After-Free in wacom_bamboo_pad wacom_bamboo_pad_pen_event() accesses wacom->shared->pen locklessly relative to wacom_remove_shared_data() which nullifies it. This can lead to a Use-After-Free if the sibling device is removed while events are being processed. Resolve this by introducing RCU protection for pen and touch pointers: - Annotate 'pen' and 'touch' in wacom_shared struct with __rcu. - Wrap lockless readers in wacom_bamboo_pad_pen_event() with rcu_read_lock() and rcu_dereference(). - Update writers in wacom_sys.c using rcu_assign_pointer(). - Use rcu_dereference_protected for comparisons under wacom_udev_list_lock. - Also use rcu_access_pointer in wacom_sibling_pending() and wacom_mode_change_work() to avoid warnings (while lockless access in the latter remains a pre-existing issue).
CVE-2026-99491 1 Linux 2 Linux, Linux Kernel 2026-11-20 7.0 High
In the Linux kernel, the following vulnerability has been resolved: HID: wacom: Fix Use-After-Free in wacom_intuos_pad wacom_intuos_pad() accesses wacom->shared->touch_input locklessly inside the interrupt handler context. If the Touch sibling device is disconnected, wacom_remove_shared_data() clears 'touch_input' outside any lock, creating a Time-of-Check to Time-of-Use (TOCTOU) race condition where a preempted reader in interrupt context dereferences the freed pointer, leading to a Use-After-Free. Resolve this by introducing RCU protection for the touch_input pointer: - Annotate 'touch_input' in wacom_shared struct with __rcu - Wrap all lockless readers in wacom_wac.c with guard(rcu)() and rcu_dereference() using a unified wacom_report_touch_mute() helper - Update writers in wacom_sys.c using rcu_assign_pointer() - Call synchronize_rcu() in wacom_remove_shared_data() to ensure all active RCU readers have finished before the input device is freed Also wrap wacom_set_shared_values() and touch/pen assignments in wacom_add_shared_data() inside the wacom_udev_list_lock to serialize concurrent probe assignments, and verify that 'shared->touch == hdev' before setting touch_input to prevent concurrent sibling probe state desynchronization.
CVE-2026-99492 1 Linux 2 Linux, Linux Kernel 2026-11-20 4.7 Medium
In the Linux kernel, the following vulnerability has been resolved: HID: wacom: Advertise SW_MUTE_DEVICE capability prior to registration Input subsystem guidelines require that device capabilities are advertised before the input device is registered. The Wacom driver was violating this by advertising the SW_MUTE_DEVICE capability post-registration in wacom_set_shared_values() (and duplicating it in device-specific setup cases). Resolve this by moving the SW_MUTE_DEVICE capability setup to wacom_setup_touch_input_capabilities() for all touch devices that support it. For generic touch devices whose capabilities depend on mute switch usages parsed from a sibling Pen/Pad interface, defer registration with -EPROBE_DEFER until the sibling has parsed its descriptors and initialized shared capabilities.
CVE-2026-99493 1 Linux 2 Linux, Linux Kernel 2026-11-20 4.7 Medium
In the Linux kernel, the following vulnerability has been resolved: s390/zcrypt: Guard domain index uses against speculative bypass The previous array_index_nospec() placement only covered the admin permission check, leaving ap_test_config_usage_domain() and ap_test_config_ctrl_domain() in the CCA path exposed to speculative execution. Move the sanitization to before all permission and config checks in both the CCA and EP11 paths. Hold the sanitized domain value in another variable so that the later use can choose to use either the original value (subject to speculative execution) or the sanitized value (which may in case of AUTOSEL_DOM reflect the wrong value). Before that, check the domain value to be either AUTOSEL_DOM or in range 0...AP_DOMAINS-1 and return with -EINVAL in case this check does not pass.
CVE-2026-99494 1 Linux 2 Linux, Linux Kernel 2026-11-20 6.1 Medium
In the Linux kernel, the following vulnerability has been resolved: s390/zcrypt: Fix out-of-bounds ptr advance in cca_query_crypto_facility() The FQ reply parser code blindly advanced the walk pointer by a length value read directly from the hardware reply payload without checking that the advance stayed within the allocated reply buffer. A corrupt or malicious device response could push ptr beyond the cprbmem region, causing an out-of-bounds dereference or kernel memory exposure via the subsequent memcpy(). Fix this by tracking the remaining reply buffer space in a variable and validating each device-supplied length field against it before advancing or dereferencing the pointer.
CVE-2026-99495 1 Linux 2 Linux, Linux Kernel 2026-11-20 6.3 Medium
In the Linux kernel, the following vulnerability has been resolved: s390/zcrypt: Fix and improve zcrypt reply message verification checks Add or improve checks related to buffer sizes and reply sizes to the handling of replies from the crypto cards for CCA, EP11 (AP message type 6) and ICA (AP type 50) messages. The verification code related to reply field length was not designed well and thus firmware deficiencies could lead to unexpected behavior in the zcrypt device driver. Thus improve the code to more closely inspect especially length fields at message replies. Add length validation before accessing reply message structures in zcrypt_msgtype6_receive(), zcrypt_msgtype6_receive_ep11(), and zcrypt_msgtype50_receive() to prevent out-of-bounds reads and potential kernel memory disclosure. Also rework these three functions to validate reply lengths more carefully before copying data back into the request buffer. Use size_t for length calculations, reject inconsistent reply sizes, and add defensive handling for short invalid replies. For XCRB replies, validate both reply segments and derive the effective message length from the covered range instead of trusting only the second segment. Additionally improve some of the later invoked evaluation functions which further check the payload. Add comments about length assumptions and for the type50 processing rework the payload processing completely with removing a misplaced BUG_ON().
CVE-2026-99496 1 Linux 2 Linux, Linux Kernel 2026-11-20 3.4 Low
In the Linux kernel, the following vulnerability has been resolved: s390/vmcp: Initialize full session info to zero The cma_alloc bit as well as the response can contain old data. cma_release will not free the kmalloced memory in that case and the response code might leak kernel stack data to CAP_SYS_ADMIN users.