Export limit exceeded: 18533 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (18533 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2022-50880 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: wifi: ath10k: add peer map clean up for peer delete in ath10k_sta_state() When peer delete failed in a disconnect operation, use-after-free detected by KFENCE in below log. It is because for each vdev_id and address, it has only one struct ath10k_peer, it is allocated in ath10k_peer_map_event(). When connected to an AP, it has more than one HTT_T2H_MSG_TYPE_PEER_MAP reported from firmware, then the array peer_map of struct ath10k will be set muti-elements to the same ath10k_peer in ath10k_peer_map_event(). When peer delete failed in ath10k_sta_state(), the ath10k_peer will be free for the 1st peer id in array peer_map of struct ath10k, and then use-after-free happened for the 2nd peer id because they map to the same ath10k_peer. And clean up all peers in array peer_map for the ath10k_peer, then user-after-free disappeared peer map event log: [ 306.911021] wlan0: authenticate with b0:2a:43:e6:75:0e [ 306.957187] ath10k_pci 0000:01:00.0: mac vdev 0 peer create b0:2a:43:e6:75:0e (new sta) sta 1 / 32 peer 1 / 33 [ 306.957395] ath10k_pci 0000:01:00.0: htt peer map vdev 0 peer b0:2a:43:e6:75:0e id 246 [ 306.957404] ath10k_pci 0000:01:00.0: htt peer map vdev 0 peer b0:2a:43:e6:75:0e id 198 [ 306.986924] ath10k_pci 0000:01:00.0: htt peer map vdev 0 peer b0:2a:43:e6:75:0e id 166 peer unmap event log: [ 435.715691] wlan0: deauthenticating from b0:2a:43:e6:75:0e by local choice (Reason: 3=DEAUTH_LEAVING) [ 435.716802] ath10k_pci 0000:01:00.0: mac vdev 0 peer delete b0:2a:43:e6:75:0e sta ffff990e0e9c2b50 (sta gone) [ 435.717177] ath10k_pci 0000:01:00.0: htt peer unmap vdev 0 peer b0:2a:43:e6:75:0e id 246 [ 435.717186] ath10k_pci 0000:01:00.0: htt peer unmap vdev 0 peer b0:2a:43:e6:75:0e id 198 [ 435.717193] ath10k_pci 0000:01:00.0: htt peer unmap vdev 0 peer b0:2a:43:e6:75:0e id 166 use-after-free log: [21705.888627] wlan0: deauthenticating from d0:76:8f:82:be:75 by local choice (Reason: 3=DEAUTH_LEAVING) [21713.799910] ath10k_pci 0000:01:00.0: failed to delete peer d0:76:8f:82:be:75 for vdev 0: -110 [21713.799925] ath10k_pci 0000:01:00.0: found sta peer d0:76:8f:82:be:75 (ptr 0000000000000000 id 102) entry on vdev 0 after it was supposedly removed [21713.799968] ================================================================== [21713.799991] BUG: KFENCE: use-after-free read in ath10k_sta_state+0x265/0xb8a [ath10k_core] [21713.799991] [21713.799997] Use-after-free read at 0x00000000abe1c75e (in kfence-#69): [21713.800010] ath10k_sta_state+0x265/0xb8a [ath10k_core] [21713.800041] drv_sta_state+0x115/0x677 [mac80211] [21713.800059] __sta_info_destroy_part2+0xb1/0x133 [mac80211] [21713.800076] __sta_info_flush+0x11d/0x162 [mac80211] [21713.800093] ieee80211_set_disassoc+0x12d/0x2f4 [mac80211] [21713.800110] ieee80211_mgd_deauth+0x26c/0x29b [mac80211] [21713.800137] cfg80211_mlme_deauth+0x13f/0x1bb [cfg80211] [21713.800153] nl80211_deauthenticate+0xf8/0x121 [cfg80211] [21713.800161] genl_rcv_msg+0x38e/0x3be [21713.800166] netlink_rcv_skb+0x89/0xf7 [21713.800171] genl_rcv+0x28/0x36 [21713.800176] netlink_unicast+0x179/0x24b [21713.800181] netlink_sendmsg+0x3a0/0x40e [21713.800187] sock_sendmsg+0x72/0x76 [21713.800192] ____sys_sendmsg+0x16d/0x1e3 [21713.800196] ___sys_sendmsg+0x95/0xd1 [21713.800200] __sys_sendmsg+0x85/0xbf [21713.800205] do_syscall_64+0x43/0x55 [21713.800210] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [21713.800213] [21713.800219] kfence-#69: 0x000000009149b0d5-0x000000004c0697fb, size=1064, cache=kmalloc-2k [21713.800219] [21713.800224] allocated by task 13 on cpu 0 at 21705.501373s: [21713.800241] ath10k_peer_map_event+0x7e/0x154 [ath10k_core] [21713.800254] ath10k_htt_t2h_msg_handler+0x586/0x1039 [ath10k_core] [21713.800265] ath10k_htt_htc_t2h_msg_handler+0x12/0x28 [ath10k_core] [21713.800277] ath10k_htc_rx_completion_handler+0x14c/0x1b5 [ath10k_core] [21713.800283] ath10k_pci_process_rx_cb+0x195/0x1d ---truncated--- | ||||
| CVE-2022-50717 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: nvmet-tcp: add bounds check on Transfer Tag ttag is used as an index to get cmd in nvmet_tcp_handle_h2c_data_pdu(), add a bounds check to avoid out-of-bounds access. | ||||
| CVE-2022-50888 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: remoteproc: qcom: q6v5: Fix potential null-ptr-deref in q6v5_wcss_init_mmio() q6v5_wcss_init_mmio() will call platform_get_resource_byname() that may fail and return NULL. devm_ioremap() will use res->start as input, which may causes null-ptr-deref. Check the ret value of platform_get_resource_byname() to avoid the null-ptr-deref. | ||||
| CVE-2025-40302 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: media: videobuf2: forbid remove_bufs when legacy fileio is active vb2_ioctl_remove_bufs() call manipulates queue internal buffer list, potentially overwriting some pointers used by the legacy fileio access mode. Forbid that ioctl when fileio is active to protect internal queue state between subsequent read/write calls. | ||||
| CVE-2025-40293 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: iommufd: Don't overflow during division for dirty tracking If pgshift is 63 then BITS_PER_TYPE(*bitmap->bitmap) * pgsize will overflow to 0 and this triggers divide by 0. In this case the index should just be 0, so reorganize things to divide by shift and avoid hitting any overflows. | ||||
| CVE-2022-50810 | 1 Linux | 1 Linux Kernel | 2026-04-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: rapidio: devices: fix missing put_device in mport_cdev_open When kfifo_alloc fails, the refcount of chdev->dev is left incremental. We should use put_device(&chdev->dev) to decrease the ref count of chdev->dev to avoid refcount leak. | ||||
| CVE-2022-50786 | 1 Linux | 1 Linux Kernel | 2026-04-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: media: s5p-mfc: Clear workbit to handle error condition During error on CLOSE_INSTANCE command, ctx_work_bits was not getting cleared. During consequent mfc execution NULL pointer dereferencing of this context led to kernel panic. This patch fixes this issue by making sure to clear ctx_work_bits always. | ||||
| CVE-2025-40041 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: LoongArch: BPF: Sign-extend struct ops return values properly The ns_bpf_qdisc selftest triggers a kernel panic: Oops[#1]: CPU 0 Unable to handle kernel paging request at virtual address 0000000000741d58, era == 90000000851b5ac0, ra == 90000000851b5aa4 CPU: 0 UID: 0 PID: 449 Comm: test_progs Tainted: G OE 6.16.0+ #3 PREEMPT(full) Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE Hardware name: QEMU QEMU Virtual Machine, BIOS unknown 2/2/2022 pc 90000000851b5ac0 ra 90000000851b5aa4 tp 90000001076b8000 sp 90000001076bb600 a0 0000000000741ce8 a1 0000000000000001 a2 90000001076bb5c0 a3 0000000000000008 a4 90000001004c4620 a5 9000000100741ce8 a6 0000000000000000 a7 0100000000000000 t0 0000000000000010 t1 0000000000000000 t2 9000000104d24d30 t3 0000000000000001 t4 4f2317da8a7e08c4 t5 fffffefffc002f00 t6 90000001004c4620 t7 ffffffffc61c5b3d t8 0000000000000000 u0 0000000000000001 s9 0000000000000050 s0 90000001075bc800 s1 0000000000000040 s2 900000010597c400 s3 0000000000000008 s4 90000001075bc880 s5 90000001075bc8f0 s6 0000000000000000 s7 0000000000741ce8 s8 0000000000000000 ra: 90000000851b5aa4 __qdisc_run+0xac/0x8d8 ERA: 90000000851b5ac0 __qdisc_run+0xc8/0x8d8 CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE) PRMD: 00000004 (PPLV0 +PIE -PWE) EUEN: 00000007 (+FPE +SXE +ASXE -BTE) ECFG: 00071c1d (LIE=0,2-4,10-12 VS=7) ESTAT: 00010000 [PIL] (IS= ECode=1 EsubCode=0) BADV: 0000000000741d58 PRID: 0014c010 (Loongson-64bit, Loongson-3A5000) Modules linked in: bpf_testmod(OE) [last unloaded: bpf_testmod(OE)] Process test_progs (pid: 449, threadinfo=000000009af02b3a, task=00000000e9ba4956) Stack : 0000000000000000 90000001075bc8ac 90000000869524a8 9000000100741ce8 90000001075bc800 9000000100415300 90000001075bc8ac 0000000000000000 900000010597c400 900000008694a000 0000000000000000 9000000105b59000 90000001075bc800 9000000100741ce8 0000000000000050 900000008513000c 9000000086936000 0000000100094d4c fffffff400676208 0000000000000000 9000000105b59000 900000008694a000 9000000086bf0dc0 9000000105b59000 9000000086bf0d68 9000000085147010 90000001075be788 0000000000000000 9000000086bf0f98 0000000000000001 0000000000000010 9000000006015840 0000000000000000 9000000086be6c40 0000000000000000 0000000000000000 0000000000000000 4f2317da8a7e08c4 0000000000000101 4f2317da8a7e08c4 ... Call Trace: [<90000000851b5ac0>] __qdisc_run+0xc8/0x8d8 [<9000000085130008>] __dev_queue_xmit+0x578/0x10f0 [<90000000853701c0>] ip6_finish_output2+0x2f0/0x950 [<9000000085374bc8>] ip6_finish_output+0x2b8/0x448 [<9000000085370b24>] ip6_xmit+0x304/0x858 [<90000000853c4438>] inet6_csk_xmit+0x100/0x170 [<90000000852b32f0>] __tcp_transmit_skb+0x490/0xdd0 [<90000000852b47fc>] tcp_connect+0xbcc/0x1168 [<90000000853b9088>] tcp_v6_connect+0x580/0x8a0 [<90000000852e7738>] __inet_stream_connect+0x170/0x480 [<90000000852e7a98>] inet_stream_connect+0x50/0x88 [<90000000850f2814>] __sys_connect+0xe4/0x110 [<90000000850f2858>] sys_connect+0x18/0x28 [<9000000085520c94>] do_syscall+0x94/0x1a0 [<9000000083df1fb8>] handle_syscall+0xb8/0x158 Code: 4001ad80 2400873f 2400832d <240073cc> 001137ff 001133ff 6407b41f 001503cc 0280041d ---[ end trace 0000000000000000 ]--- The bpf_fifo_dequeue prog returns a skb which is a pointer. The pointer is treated as a 32bit value and sign extend to 64bit in epilogue. This behavior is right for most bpf prog types but wrong for struct ops which requires LoongArch ABI. So let's sign extend struct ops return values according to the LoongArch ABI ([1]) and return value spec in function model. [1]: https://loongson.github.io/LoongArch-Documentation/LoongArch-ELF-ABI-EN.html | ||||
| CVE-2023-53709 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ring-buffer: Handle race between rb_move_tail and rb_check_pages It seems a data race between ring_buffer writing and integrity check. That is, RB_FLAG of head_page is been updating, while at same time RB_FLAG was cleared when doing integrity check rb_check_pages(): rb_check_pages() rb_handle_head_page(): -------- -------- rb_head_page_deactivate() rb_head_page_set_normal() rb_head_page_activate() We do intergrity test of the list to check if the list is corrupted and it is still worth doing it. So, let's refactor rb_check_pages() such that we no longer clear and set flag during the list sanity checking. [1] and [2] are the test to reproduce and the crash report respectively. 1: ``` read_trace.sh while true; do # the "trace" file is closed after read head -1 /sys/kernel/tracing/trace > /dev/null done ``` ``` repro.sh sysctl -w kernel.panic_on_warn=1 # function tracer will writing enough data into ring_buffer echo function > /sys/kernel/tracing/current_tracer ./read_trace.sh & ./read_trace.sh & ./read_trace.sh & ./read_trace.sh & ./read_trace.sh & ./read_trace.sh & ./read_trace.sh & ./read_trace.sh & ``` 2: ------------[ cut here ]------------ WARNING: CPU: 9 PID: 62 at kernel/trace/ring_buffer.c:2653 rb_move_tail+0x450/0x470 Modules linked in: CPU: 9 PID: 62 Comm: ksoftirqd/9 Tainted: G W 6.2.0-rc6+ Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014 RIP: 0010:rb_move_tail+0x450/0x470 Code: ff ff 4c 89 c8 f0 4d 0f b1 02 48 89 c2 48 83 e2 fc 49 39 d0 75 24 83 e0 03 83 f8 02 0f 84 e1 fb ff ff 48 8b 57 10 f0 ff 42 08 <0f> 0b 83 f8 02 0f 84 ce fb ff ff e9 db RSP: 0018:ffffb5564089bd00 EFLAGS: 00000203 RAX: 0000000000000000 RBX: ffff9db385a2bf81 RCX: ffffb5564089bd18 RDX: ffff9db281110100 RSI: 0000000000000fe4 RDI: ffff9db380145400 RBP: ffff9db385a2bf80 R08: ffff9db385a2bfc0 R09: ffff9db385a2bfc2 R10: ffff9db385a6c000 R11: ffff9db385a2bf80 R12: 0000000000000000 R13: 00000000000003e8 R14: ffff9db281110100 R15: ffffffffbb006108 FS: 0000000000000000(0000) GS:ffff9db3bdcc0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00005602323024c8 CR3: 0000000022e0c000 CR4: 00000000000006e0 Call Trace: <TASK> ring_buffer_lock_reserve+0x136/0x360 ? __do_softirq+0x287/0x2df ? __pfx_rcu_softirq_qs+0x10/0x10 trace_function+0x21/0x110 ? __pfx_rcu_softirq_qs+0x10/0x10 ? __do_softirq+0x287/0x2df function_trace_call+0xf6/0x120 0xffffffffc038f097 ? rcu_softirq_qs+0x5/0x140 rcu_softirq_qs+0x5/0x140 __do_softirq+0x287/0x2df run_ksoftirqd+0x2a/0x30 smpboot_thread_fn+0x188/0x220 ? __pfx_smpboot_thread_fn+0x10/0x10 kthread+0xe7/0x110 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2c/0x50 </TASK> ---[ end trace 0000000000000000 ]--- [ crash report and test reproducer credit goes to Zheng Yejian] | ||||
| CVE-2023-54035 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: fix underflow in chain reference counter Set element addition error path decrements reference counter on chains twice: once on element release and again via nft_data_release(). Then, d6b478666ffa ("netfilter: nf_tables: fix underflow in object reference counter") incorrectly fixed this by removing the stateful object reference count decrement. Restore the stateful object decrement as in b91d90368837 ("netfilter: nf_tables: fix leaking object reference count") and let nft_data_release() decrement the chain reference counter, so this is done only once. | ||||
| CVE-2025-40184 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Fix debug checking for np-guests using huge mappings When running with transparent huge pages and CONFIG_NVHE_EL2_DEBUG then the debug checking in assert_host_shared_guest() fails on the launch of an np-guest. This WARN_ON() causes a panic and generates the stack below. In __pkvm_host_relax_perms_guest() the debug checking assumes the mapping is a single page but it may be a block map. Update the checking so that the size is not checked and just assumes the correct size. While we're here make the same fix in __pkvm_host_mkyoung_guest(). Info: # lkvm run -k /share/arch/arm64/boot/Image -m 704 -c 8 --name guest-128 Info: Removed ghost socket file "/.lkvm//guest-128.sock". [ 1406.521757] kvm [141]: nVHE hyp BUG at: arch/arm64/kvm/hyp/nvhe/mem_protect.c:1088! [ 1406.521804] kvm [141]: nVHE call trace: [ 1406.521828] kvm [141]: [<ffff8000811676b4>] __kvm_nvhe_hyp_panic+0xb4/0xe8 [ 1406.521946] kvm [141]: [<ffff80008116d12c>] __kvm_nvhe_assert_host_shared_guest+0xb0/0x10c [ 1406.522049] kvm [141]: [<ffff80008116f068>] __kvm_nvhe___pkvm_host_relax_perms_guest+0x48/0x104 [ 1406.522157] kvm [141]: [<ffff800081169df8>] __kvm_nvhe_handle___pkvm_host_relax_perms_guest+0x64/0x7c [ 1406.522250] kvm [141]: [<ffff800081169f0c>] __kvm_nvhe_handle_trap+0x8c/0x1a8 [ 1406.522333] kvm [141]: [<ffff8000811680fc>] __kvm_nvhe___skip_pauth_save+0x4/0x4 [ 1406.522454] kvm [141]: ---[ end nVHE call trace ]--- [ 1406.522477] kvm [141]: Hyp Offset: 0xfffece8013600000 [ 1406.522554] Kernel panic - not syncing: HYP panic: [ 1406.522554] PS:834003c9 PC:0000b1806db6d170 ESR:00000000f2000800 [ 1406.522554] FAR:ffff8000804be420 HPFAR:0000000000804be0 PAR:0000000000000000 [ 1406.522554] VCPU:0000000000000000 [ 1406.523337] CPU: 3 UID: 0 PID: 141 Comm: kvm-vcpu-0 Not tainted 6.16.0-rc7 #97 PREEMPT [ 1406.523485] Hardware name: FVP Base RevC (DT) [ 1406.523566] Call trace: [ 1406.523629] show_stack+0x18/0x24 (C) [ 1406.523753] dump_stack_lvl+0xd4/0x108 [ 1406.523899] dump_stack+0x18/0x24 [ 1406.524040] panic+0x3d8/0x448 [ 1406.524184] nvhe_hyp_panic_handler+0x10c/0x23c [ 1406.524325] kvm_handle_guest_abort+0x68c/0x109c [ 1406.524500] handle_exit+0x60/0x17c [ 1406.524630] kvm_arch_vcpu_ioctl_run+0x2e0/0x8c0 [ 1406.524794] kvm_vcpu_ioctl+0x1a8/0x9cc [ 1406.524919] __arm64_sys_ioctl+0xac/0x104 [ 1406.525067] invoke_syscall+0x48/0x10c [ 1406.525189] el0_svc_common.constprop.0+0x40/0xe0 [ 1406.525322] do_el0_svc+0x1c/0x28 [ 1406.525441] el0_svc+0x38/0x120 [ 1406.525588] el0t_64_sync_handler+0x10c/0x138 [ 1406.525750] el0t_64_sync+0x1ac/0x1b0 [ 1406.525876] SMP: stopping secondary CPUs [ 1406.525965] Kernel Offset: disabled [ 1406.526032] CPU features: 0x0000,00000080,8e134ca1,9446773f [ 1406.526130] Memory Limit: none [ 1406.959099] ---[ end Kernel panic - not syncing: HYP panic: [ 1406.959099] PS:834003c9 PC:0000b1806db6d170 ESR:00000000f2000800 [ 1406.959099] FAR:ffff8000804be420 HPFAR:0000000000804be0 PAR:0000000000000000 [ 1406.959099] VCPU:0000000000000000 ] | ||||
| CVE-2022-50778 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: fortify: Fix __compiletime_strlen() under UBSAN_BOUNDS_LOCAL With CONFIG_FORTIFY=y and CONFIG_UBSAN_LOCAL_BOUNDS=y enabled, we observe a runtime panic while running Android's Compatibility Test Suite's (CTS) android.hardware.input.cts.tests. This is stemming from a strlen() call in hidinput_allocate(). __compiletime_strlen() is implemented in terms of __builtin_object_size(), then does an array access to check for NUL-termination. A quirk of __builtin_object_size() is that for strings whose values are runtime dependent, __builtin_object_size(str, 1 or 0) returns the maximum size of possible values when those sizes are determinable at compile time. Example: static const char *v = "FOO BAR"; static const char *y = "FOO BA"; unsigned long x (int z) { // Returns 8, which is: // max(__builtin_object_size(v, 1), __builtin_object_size(y, 1)) return __builtin_object_size(z ? v : y, 1); } So when FORTIFY_SOURCE is enabled, the current implementation of __compiletime_strlen() will try to access beyond the end of y at runtime using the size of v. Mixed with UBSAN_LOCAL_BOUNDS we get a fault. hidinput_allocate() has a local C string whose value is control flow dependent on a switch statement, so __builtin_object_size(str, 1) evaluates to the maximum string length, making all other cases fault on the last character check. hidinput_allocate() could be cleaned up to avoid runtime calls to strlen() since the local variable can only have literal values, so there's no benefit to trying to fortify the strlen call site there. Perform a __builtin_constant_p() check against index 0 earlier in the macro to filter out the control-flow-dependant case. Add a KUnit test for checking the expected behavioral characteristics of FORTIFY_SOURCE internals. | ||||
| CVE-2023-54043 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: iommufd: Do not add the same hwpt to the ioas->hwpt_list twice The hwpt is added to the hwpt_list only during its creation, it is never added again. This hunk is some missed leftover from rework. Adding it twice will corrupt the linked list in some cases. It effects HWPT specific attachment, which is something the test suite cannot cover until we can create a legitimate struct device with a non-system iommu "driver" (ie we need the bus removed from the iommu code) | ||||
| CVE-2025-68319 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: netconsole: Acquire su_mutex before navigating configs hierarchy There is a race between operations that iterate over the userdata cg_children list and concurrent add/remove of userdata items through configfs. The update_userdata() function iterates over the nt->userdata_group.cg_children list, and count_extradata_entries() also iterates over this same list to count nodes. Quoting from Documentation/filesystems/configfs.rst: > A subsystem can navigate the cg_children list and the ci_parent pointer > to see the tree created by the subsystem. This can race with configfs' > management of the hierarchy, so configfs uses the subsystem mutex to > protect modifications. Whenever a subsystem wants to navigate the > hierarchy, it must do so under the protection of the subsystem > mutex. Without proper locking, if a userdata item is added or removed concurrently while these functions are iterating, the list can be accessed in an inconsistent state. For example, the list_for_each() loop can reach a node that is being removed from the list by list_del_init() which sets the nodes' .next pointer to point to itself, so the loop will never end (or reach the WARN_ON_ONCE in update_userdata() ). Fix this by holding the configfs subsystem mutex (su_mutex) during all operations that iterate over cg_children. This includes: - userdatum_value_store() which calls update_userdata() to iterate over cg_children - All sysdata_*_enabled_store() functions which call count_extradata_entries() to iterate over cg_children The su_mutex must be acquired before dynamic_netconsole_mutex to avoid potential lock ordering issues, as configfs operations may already hold su_mutex when calling into our code. | ||||
| CVE-2025-68305 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_sock: Prevent race in socket write iter and sock bind There is a potential race condition between sock bind and socket write iter. bind may free the same cmd via mgmt_pending before write iter sends the cmd, just as syzbot reported in UAF[1]. Here we use hci_dev_lock to synchronize the two, thereby avoiding the UAF mentioned in [1]. [1] syzbot reported: BUG: KASAN: slab-use-after-free in mgmt_pending_remove+0x3b/0x210 net/bluetooth/mgmt_util.c:316 Read of size 8 at addr ffff888077164818 by task syz.0.17/5989 Call Trace: mgmt_pending_remove+0x3b/0x210 net/bluetooth/mgmt_util.c:316 set_link_security+0x5c2/0x710 net/bluetooth/mgmt.c:1918 hci_mgmt_cmd+0x9c9/0xef0 net/bluetooth/hci_sock.c:1719 hci_sock_sendmsg+0x6ca/0xef0 net/bluetooth/hci_sock.c:1839 sock_sendmsg_nosec net/socket.c:727 [inline] __sock_sendmsg+0x21c/0x270 net/socket.c:742 sock_write_iter+0x279/0x360 net/socket.c:1195 Allocated by task 5989: mgmt_pending_add+0x35/0x140 net/bluetooth/mgmt_util.c:296 set_link_security+0x557/0x710 net/bluetooth/mgmt.c:1910 hci_mgmt_cmd+0x9c9/0xef0 net/bluetooth/hci_sock.c:1719 hci_sock_sendmsg+0x6ca/0xef0 net/bluetooth/hci_sock.c:1839 sock_sendmsg_nosec net/socket.c:727 [inline] __sock_sendmsg+0x21c/0x270 net/socket.c:742 sock_write_iter+0x279/0x360 net/socket.c:1195 Freed by task 5991: mgmt_pending_free net/bluetooth/mgmt_util.c:311 [inline] mgmt_pending_foreach+0x30d/0x380 net/bluetooth/mgmt_util.c:257 mgmt_index_removed+0x112/0x2f0 net/bluetooth/mgmt.c:9477 hci_sock_bind+0xbe9/0x1000 net/bluetooth/hci_sock.c:1314 | ||||
| CVE-2025-68304 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_core: lookup hci_conn on RX path on protocol side The hdev lock/lookup/unlock/use pattern in the packet RX path doesn't ensure hci_conn* is not concurrently modified/deleted. This locking appears to be leftover from before conn_hash started using RCU commit bf4c63252490b ("Bluetooth: convert conn hash to RCU") and not clear if it had purpose since then. Currently, there are code paths that delete hci_conn* from elsewhere than the ordered hdev->workqueue where the RX work runs in. E.g. commit 5af1f84ed13a ("Bluetooth: hci_sync: Fix UAF on hci_abort_conn_sync") introduced some of these, and there probably were a few others before it. It's better to do the locking so that even if these run concurrently no UAF is possible. Move the lookup of hci_conn and associated socket-specific conn to protocol recv handlers, and do them within a single critical section to cover hci_conn* usage and lookup. syzkaller has reported a crash that appears to be this issue: [Task hdev->workqueue] [Task 2] hci_disconnect_all_sync l2cap_recv_acldata(hcon) hci_conn_get(hcon) hci_abort_conn_sync(hcon) hci_dev_lock hci_dev_lock hci_conn_del(hcon) v-------------------------------- hci_dev_unlock hci_conn_put(hcon) conn = hcon->l2cap_data (UAF) | ||||
| CVE-2025-68299 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: afs: Fix delayed allocation of a cell's anonymous key The allocation of a cell's anonymous key is done in a background thread along with other cell setup such as doing a DNS upcall. In the reported bug, this is triggered by afs_parse_source() parsing the device name given to mount() and calling afs_lookup_cell() with the name of the cell. The normal key lookup then tries to use the key description on the anonymous authentication key as the reference for request_key() - but it may not yet be set and so an oops can happen. This has been made more likely to happen by the fix for dynamic lookup failure. Fix this by firstly allocating a reference name and attaching it to the afs_cell record when the record is created. It can share the memory allocation with the cell name (unfortunately it can't just overlap the cell name by prepending it with "afs@" as the cell name already has a '.' prepended for other purposes). This reference name is then passed to request_key(). Secondly, the anon key is now allocated on demand at the point a key is requested in afs_request_key() if it is not already allocated. A mutex is used to prevent multiple allocation for a cell. Thirdly, make afs_request_key_rcu() return NULL if the anonymous key isn't yet allocated (if we need it) and then the caller can return -ECHILD to drop out of RCU-mode and afs_request_key() can be called. Note that the anonymous key is kind of necessary to make the key lookup cache work as that doesn't currently cache a negative lookup, but it's probably worth some investigation to see if NULL can be used instead. | ||||
| CVE-2025-68298 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btusb: mediatek: Avoid btusb_mtk_claim_iso_intf() NULL deref In btusb_mtk_setup(), we set `btmtk_data->isopkt_intf` to: usb_ifnum_to_if(data->udev, MTK_ISO_IFNUM) That function can return NULL in some cases. Even when it returns NULL, though, we still go on to call btusb_mtk_claim_iso_intf(). As of commit e9087e828827 ("Bluetooth: btusb: mediatek: Add locks for usb_driver_claim_interface()"), calling btusb_mtk_claim_iso_intf() when `btmtk_data->isopkt_intf` is NULL will cause a crash because we'll end up passing a bad pointer to device_lock(). Prior to that commit we'd pass the NULL pointer directly to usb_driver_claim_interface() which would detect it and return an error, which was handled. Resolve the crash in btusb_mtk_claim_iso_intf() by adding a NULL check at the start of the function. This makes the code handle a NULL `btmtk_data->isopkt_intf` the same way it did before the problematic commit (just with a slight change to the error message printed). | ||||
| CVE-2025-68296 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: drm, fbcon, vga_switcheroo: Avoid race condition in fbcon setup Protect vga_switcheroo_client_fb_set() with console lock. Avoids OOB access in fbcon_remap_all(). Without holding the console lock the call races with switching outputs. VGA switcheroo calls fbcon_remap_all() when switching clients. The fbcon function uses struct fb_info.node, which is set by register_framebuffer(). As the fb-helper code currently sets up VGA switcheroo before registering the framebuffer, the value of node is -1 and therefore not a legal value. For example, fbcon uses the value within set_con2fb_map() [1] as an index into an array. Moving vga_switcheroo_client_fb_set() after register_framebuffer() can result in VGA switching that does not switch fbcon correctly. Therefore move vga_switcheroo_client_fb_set() under fbcon_fb_registered(), which already holds the console lock. Fbdev calls fbcon_fb_registered() from within register_framebuffer(). Serializes the helper with VGA switcheroo's call to fbcon_remap_all(). Although vga_switcheroo_client_fb_set() takes an instance of struct fb_info as parameter, it really only needs the contained fbcon state. Moving the call to fbcon initialization is therefore cleaner than before. Only amdgpu, i915, nouveau and radeon support vga_switcheroo. For all other drivers, this change does nothing. | ||||
| CVE-2025-68339 | 1 Linux | 1 Linux Kernel | 2026-04-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: atm/fore200e: Fix possible data race in fore200e_open() Protect access to fore200e->available_cell_rate with rate_mtx lock in the error handling path of fore200e_open() to prevent a data race. The field fore200e->available_cell_rate is a shared resource used to track available bandwidth. It is concurrently accessed by fore200e_open(), fore200e_close(), and fore200e_change_qos(). In fore200e_open(), the lock rate_mtx is correctly held when subtracting vcc->qos.txtp.max_pcr from available_cell_rate to reserve bandwidth. However, if the subsequent call to fore200e_activate_vcin() fails, the function restores the reserved bandwidth by adding back to available_cell_rate without holding the lock. This introduces a race condition because available_cell_rate is a global device resource shared across all VCCs. If the error path in fore200e_open() executes concurrently with operations like fore200e_close() or fore200e_change_qos() on other VCCs, a read-modify-write race occurs. Specifically, the error path reads the rate without the lock. If another CPU acquires the lock and modifies the rate (e.g., releasing bandwidth in fore200e_close()) between this read and the subsequent write, the error path will overwrite the concurrent update with a stale value. This results in incorrect bandwidth accounting. | ||||