In the Linux kernel, the following vulnerability has been resolved:
spi: spi-qpic-snand: write the feature value before executing SET_FEATURE
qcom_spi_send_cmdaddr() programs NAND_FLASH_CMD/NAND_EXEC_CMD and submits
the descriptors, which makes the controller execute the command
immediately. For SPINAND_SET_FEATURE the value to be written is only
placed into NAND_FLASH_FEATURES afterwards, by qcom_spi_io_op(), in a
second submission - so the chip is programmed with whatever that register
happened to hold from a previous operation, and the intended value is only
applied by the *next* SET_FEATURE.
Measured on a TP-Link Archer AX55 v1 (IPQ5018, ESMT F50L1G41LB): writing
0x40 to the configuration register (0xb0) leaves the chip at 0x00, and the
subsequent write of 0x00 leaves it at 0x40 - every write lands one
operation late.
This stayed unnoticed until v6.18 added SPI-NAND OTP support together
with OTP entries for ESMT chips. spinand_otp_rw() enables OTP mode,
reads, and disables it again, and mtd_otp_nvmem_add() does this during
MTD registration. With the off-by-one, the "disable" write actually
applies the previously requested value, so CFG_OTP_ENABLE ends up set:
the chip stays in OTP mode, every subsequent array read returns the OTP
area instead of the array (UBI reports an empty device) and all writes
fail with -EIO because the OTP area is write protected. On this board
that makes the whole flash unusable and the device unbootable.
Write the feature value into NAND_FLASH_FEATURES as part of the same
transaction, before NAND_EXEC_CMD. While at it, copy only the bytes the
operation actually carries - the previous code dereferenced a 4-byte
pointer on a one-byte buffer (spinand->scratchbuf).
With this patch the flash contents read back bit-identical to a
known-good dump of the same board taken under the vendor firmware
(md5-verified across partitions), and writes work.
spi: spi-qpic-snand: write the feature value before executing SET_FEATURE
qcom_spi_send_cmdaddr() programs NAND_FLASH_CMD/NAND_EXEC_CMD and submits
the descriptors, which makes the controller execute the command
immediately. For SPINAND_SET_FEATURE the value to be written is only
placed into NAND_FLASH_FEATURES afterwards, by qcom_spi_io_op(), in a
second submission - so the chip is programmed with whatever that register
happened to hold from a previous operation, and the intended value is only
applied by the *next* SET_FEATURE.
Measured on a TP-Link Archer AX55 v1 (IPQ5018, ESMT F50L1G41LB): writing
0x40 to the configuration register (0xb0) leaves the chip at 0x00, and the
subsequent write of 0x00 leaves it at 0x40 - every write lands one
operation late.
This stayed unnoticed until v6.18 added SPI-NAND OTP support together
with OTP entries for ESMT chips. spinand_otp_rw() enables OTP mode,
reads, and disables it again, and mtd_otp_nvmem_add() does this during
MTD registration. With the off-by-one, the "disable" write actually
applies the previously requested value, so CFG_OTP_ENABLE ends up set:
the chip stays in OTP mode, every subsequent array read returns the OTP
area instead of the array (UBI reports an empty device) and all writes
fail with -EIO because the OTP area is write protected. On this board
that makes the whole flash unusable and the device unbootable.
Write the feature value into NAND_FLASH_FEATURES as part of the same
transaction, before NAND_EXEC_CMD. While at it, copy only the bytes the
operation actually carries - the previous code dereferenced a 4-byte
pointer on a one-byte buffer (spinand->scratchbuf).
With this patch the flash contents read back bit-identical to a
known-good dump of the same board taken under the vendor firmware
(md5-verified across partitions), and writes work.
Default status is the baseline for the product, each version can override it (e.g. patched versions marked unaffected).
| Vendor | Product | Default status | Versions | ||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Linux | Linux | unaffected |
|
||||||||||||||||||
| Linux | Linux | affected |
|
No data.
No data.
OpenCVE Enrichment is a feature of OpenCVE that uses AI to automatically link vendors and products to CVEs. Learn more on GitHub.
No data.
Advisories
No advisories yet.
Fixes
Solution
No solution given by the vendor.
Workaround
No workaround given by the vendor.
References
History
Fri, 28 Aug 2026 11:45:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| Weaknesses | CWE-119 CWE-125 CWE-482 |
Fri, 28 Aug 2026 07:30:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| Description | In the Linux kernel, the following vulnerability has been resolved: spi: spi-qpic-snand: write the feature value before executing SET_FEATURE qcom_spi_send_cmdaddr() programs NAND_FLASH_CMD/NAND_EXEC_CMD and submits the descriptors, which makes the controller execute the command immediately. For SPINAND_SET_FEATURE the value to be written is only placed into NAND_FLASH_FEATURES afterwards, by qcom_spi_io_op(), in a second submission - so the chip is programmed with whatever that register happened to hold from a previous operation, and the intended value is only applied by the *next* SET_FEATURE. Measured on a TP-Link Archer AX55 v1 (IPQ5018, ESMT F50L1G41LB): writing 0x40 to the configuration register (0xb0) leaves the chip at 0x00, and the subsequent write of 0x00 leaves it at 0x40 - every write lands one operation late. This stayed unnoticed until v6.18 added SPI-NAND OTP support together with OTP entries for ESMT chips. spinand_otp_rw() enables OTP mode, reads, and disables it again, and mtd_otp_nvmem_add() does this during MTD registration. With the off-by-one, the "disable" write actually applies the previously requested value, so CFG_OTP_ENABLE ends up set: the chip stays in OTP mode, every subsequent array read returns the OTP area instead of the array (UBI reports an empty device) and all writes fail with -EIO because the OTP area is write protected. On this board that makes the whole flash unusable and the device unbootable. Write the feature value into NAND_FLASH_FEATURES as part of the same transaction, before NAND_EXEC_CMD. While at it, copy only the bytes the operation actually carries - the previous code dereferenced a 4-byte pointer on a one-byte buffer (spinand->scratchbuf). With this patch the flash contents read back bit-identical to a known-good dump of the same board taken under the vendor firmware (md5-verified across partitions), and writes work. | |
| Title | spi: spi-qpic-snand: write the feature value before executing SET_FEATURE | |
| First Time appeared |
Linux
Linux linux Kernel |
|
| CPEs | cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:* | |
| Vendors & Products |
Linux
Linux linux Kernel |
|
| References |
|
Projects
Sign in to view the affected projects.
MITRE
Status: PUBLISHED
Assigner: Linux
Published:
Updated: 2026-08-28T06:53:11.243Z
Reserved: 2026-08-26T14:34:25.788Z
Link: CVE-2026-80712
Vulnrichment
No data.
NVD
Status : Received
Published: 2026-08-28T08:16:56.850
Modified: 2026-08-28T08:16:56.850
Link: CVE-2026-80712
Redhat
No data.
OpenCVE Enrichment
Updated: 2026-08-28T11:30:06Z