| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: dwc: ep: Flush cached MSI write before unmapping the iATU
The MSI-X path already flushes any posted MSI-X write before tearing down
its iATU mapping. That was added by commit c22533c66cca ("PCI: dwc: ep:
Flush MSI-X write before unmapping its ATU entry") to make sure the write
reaches the Root Complex before the outbound window that translates it
disappears.
The MSI path has the same problem but no equivalent flush. When the
Endpoint driver caches an MSI target address and later observes that the
Root Complex has changed it, dw_pcie_ep_raise_msi_irq() unmaps the existing
iATU entry and reprograms it for the new address. Between the last MSI
writel() and the unmap there may still be a posted write sitting in the
fabric, and unmapping the iATU entry can drop or misroute that write.
Fix this by reading back from the mapped MSI window before the unmap. The
readback drains any posted MSI writes through the same iATU entry that
mapped them, which is the same logic the MSI-X path uses.
[mani: commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: ptrace: Keep 'orig_x0' in-sync with x0 on syscall entry
Commit e057b9477232 ("arm64: syscall: Ensure saved x0 is kept in-sync
with tracer updates") attempted to resolve a long-standing issue with
syscall entry tracing, where a tracer is able to manipulate the first
syscall argument without being subjected to seccomp or audit checking.
Unfortunately, that fix was incomplete [1], as it failed to update
'orig_x0' between a tracer updating x0 during a seccomp ptrace exit
(SECCOMP_RET_TRACE) and the seccomp filter being re-evaluated.
Rather than add hooks to the core seccomp code, instead move the
synchronisation code into the ptrace GPR and syscall setting code so
that 'orig_x0' is kept up to date with x0 whenever we're stopped on the
syscall entry path. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt792x: fix use-after-free in mt76_rx_poll_complete
A use-after-free issue occurs in mt76_rx_poll_complete due to a race
condition. The STA has already been removed, but the rx_status still
had a pointer to the wcid in the STA.
Set the links' wcid pointers to be NULL for a MLD in
mt7925_sta_pre_rcu_remove()
BUG: KASAN: invalid-access in mt76_rx_poll_complete+0x280/0x470
Call trace:
dump_backtrace+0xec/0x128
show_stack+0x18/0x28
dump_stack_lvl+0x40/0xc8
print_report+0x1b8/0x710
kasan_report+0xe0/0x144
do_bad_area+0x120/0x260
do_tag_check_fault+0x20/0x34
do_mem_abort+0x54/0xa8
el1_abort+0x3c/0x5c
el1h_64_sync_handler+0x40/0xcc
el1h_64_sync+0x7c/0x80
mt76_rx_poll_complete+0x280/0x470
mt76_dma_rx_poll+0x114/0x51c
mt792x_poll_rx+0x60/0xf8
napi_threaded_poll_loop+0xe0/0x450
napi_threaded_poll+0x80/0x9c
kthread+0x11c/0x158
ret_from_fork+0x10/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
swiotlb: Preserve allocation virtual address for dynamic pools
swiotlb_alloc_tlb() can allocate from the DMA atomic pool when a decrypted
pool is needed from atomic context. With CONFIG_DMA_DIRECT_REMAP, the
atomic pool is backed by remapped virtual addresses, which are not the same
as the direct-map addresses returned by phys_to_virt().
swiotlb_init_io_tlb_pool() currently reconstructs the pool virtual address
from the physical start address. For atomic-pool backed allocations this
stores the wrong address in pool->vaddr. Later, swiotlb_free_tlb() passes
that address to dma_free_from_pool(), which will fail to recognize the
chunk
Pass the virtual address returned by the allocation path into
swiotlb_init_io_tlb_pool(), and store that address in pool->vaddr. This
keeps the pool free path using the same virtual address as the allocator. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/dma: Check atomic pool allocation result directly
The non-blocking, non-coherent allocation path uses dma_alloc_from_pool(),
which returns the allocated page and fills cpu_addr only on success.
Do not rely on cpu_addr to detect allocation failure in this path. Check
the returned page directly before using it for the IOMMU mapping. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/tegra241-cmdqv: Require exactly one Stream ID for a vSID
tegra241_vintf_init_vsid() maps a guest vSID to a single physical Stream ID
taken from master->streams[0], and only warns when the device does not have
exactly one stream. A device with several streams gets only its first one
mapped, so a guest vSID invalidation cannot reach the others' ATC and IOTLB
entries; a device with none makes master->streams a ZERO_SIZE_PTR, read out
of bounds.
Reject the mapping with -EOPNOTSUPP if master->num_streams is not one. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/tegra241-cmdqv: Don't fall back to a freed smmu after devm_krealloc()
__tegra241_cmdqv_probe() uses devm_krealloc() to grow @smmu into the larger
tegra241_cmdqv, which frees the original @smmu once it relocates. A failure
after that returned NULL, and the caller then dereferenced the freed @smmu
on its fallback path.
Return an int and take @smmu by reference instead, then update *smmu to the
reallocated pointer after devm_krealloc() succeeds, so the caller and its
fallback path both use the live @smmu rather than the freed original. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/tegra241-cmdqv: Synchronize the error ISR against VINTF (de)init
A user VINTF is torn down by tegra241_cmdqv_deinit_vintf(), which runs from
the destroy callback and from the init-failure unwind in the alloc handler.
It clears the cmdqv->vintfs[] slot and lets the iommufd core free it, but
nothing serializes that against the error interrupt: tegra241_cmdqv_isr()
reads cmdqv->vintfs[idx] and dereferences the vintf. A concurrent error can
make the ISR read a slot mid-clear (a NULL deref) or use a vintf which is
about to be freed (a use-after-free).
deinit_vintf() also returns idx to the IDA before clearing the slot, so a
concurrent create that reuses idx can publish its new vintf into the slot,
only for this teardown to erase it again with the stale NULL store.
On the other end, tegra241_cmdqv_init_vintf() publishes a new vintf with a
plain store to the cmdqv->vintfs[] slot, and the ISR dereferences fields of
a published vintf such as vintf->base. A plain store gives no ordering on a
weakly-ordered CPU, and a stale VINTF_ERR_MAP bit on a reused idx can make
the ISR pick a vintf the moment it is published, before its fields are set
or tegra241_vintf_hw_init() runs.
The cmdqv->vintfs[0] slot stays NULL until tegra241_cmdqv_init_structures()
first creates VINTF0, so the slot 0 read needs the same NULL check.
Publish every slot with an smp_store_release(), and read each slot in the
ISR with an smp_load_acquire() under a NULL check, so the ISR always sees
a fully built vintf or NULL. Also make deinit_vintf() clear the slot, and
synchronize_irq() prior to returning idx to the IDA, so no vintf is freed
under a running handler and no reused idx is clobbered. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx5: Fix integer overflow of user QP buffer size
set_user_buf_size() computes the QP buffer size by left-shifting the
user-supplied rq.wqe_cnt and rq.wqe_shift values as signed integers.
A sufficiently large rq.wqe_cnt causes signed integer overflow, which
is undefined behavior, and yields a small or negative buf_size, causing
ib_umem_get() to map a buffer smaller than the hardware will actually
write into.
Replace the shifts and addition with check_shl_overflow() and
check_add_overflow(), rejecting invalid user inputs.
Moreover, guard the identical shift computing qp->sq.offset in
_create_user_qp() before set_user_buf_size() is reached. |
| In the Linux kernel, the following vulnerability has been resolved:
thermal: intel: int3400: clean up ODVP on probe failures
evaluate_odvp() creates per-ODVP sysfs files before the thermal zone
and later probe resources are registered. The current unwind path only
calls cleanup_odvp() from the late sysfs failure path, so failures after
evaluate_odvp() but before that label, including
thermal_tripless_zone_device_register() failures, leave the ODVP files
and storage behind.
Move the ODVP cleanup to the common ART/TRT unwind path so every failure
after evaluate_odvp() releases the ODVP state. Also clear the cached
ODVP pointers in cleanup_odvp(), because evaluate_odvp() can already call
it for partial setup failures while probe continues. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/core: Fix potential use after free in ib_destroy_cq_user()
When accessing a CQ via the netlink path the only synchronization
mechanism for the said CQ is rdma_restrack_get().
Currently, rdma_restrack_del() is invoked at the end of
ib_destroy_cq_user(), which is too late, since by that point
vendor-specific resources associated with the CQ might already be
freed. This can leave a short window where the CQ remains accessible
through restrack, leading to a potential use-after-free.
Fix this by moving the rdma_restrack_begin_del() call to the start of
ib_destroy_cq_user(), ensuring that the CQ is removed from restrack
before its internal resources are released. This guarantees that no new
users hold references to a CQ that is in the process of destruction.
In addition, this change preserves the intended inverted order
between create and destroy routines: resources are added to
restrack at the end of successful creation, and hence shall be removed
from the restrack first thing during the destruction flow, which keeps
the lifecycle management consistent and predictable. |
| Exim before 4.100.1, when Proxy-Protocol is used with an attacker-controlled proxy, has an out-of-bounds write. |
| Exim before 4.100.1, when certain non-default TLS settings are used with GnuTLS, has a use-after-free. |
| Exim before 4.100.1, when Proxy-Protocol is used with an attacker-controlled proxy, allows attackers to read certain uninitialized data from stack memory. |
| Exim before 4.100.1 allows SMTP smuggling in which the received message does not match any sent message, and instead depends on crafted data sent after a rejection during DATA processing. |
| In the Linux kernel, the following vulnerability has been resolved:
hfsplus: validate thread record before delete key rebuild
hfsplus_delete_cat() is called with str == NULL when the last open
reference to an unlinked HFS+ hardlink backing inode is closed. In that
case, the function finds the catalog thread by CNID and rebuilds the
catalog key from thread.nodeName.
That reconstruction path reads thread.nodeName.length directly from the
catalog B-tree into fd.search_key and then copies length * 2 bytes into
fd.search_key->cat.name.unicode. It does not first check that the found
record is a thread record or that its size matches the thread name.
A corrupted image can therefore provide an oversized thread name length
and make hfs_bnode_read() write past the catalog search-key allocation.
Read the CNID record through hfsplus_brec_read_cat(), which bounds the
record read to sizeof(hfsplus_cat_entry) and verifies that a thread
record's size exactly matches nodeName.length. Together, these checks
ensure an accepted thread name fits HFSPLUS_MAX_STRLEN. Reject non-thread
records before building the delete key from the validated thread name.
Share the thread-record-type helper between hfsplus_find_cat() and
hfsplus_delete_cat(). |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_fs: Fix fence cleanup in ffs_dmabuf_transfer() error paths
The error paths for endpoint-disabled (ESHUTDOWN) and request-allocation
failure (ENOMEM) in ffs_dmabuf_transfer() jump to err_fence_put which
calls dma_fence_put() on the fence. However, at that point the fence has
only been kmalloc'd — dma_fence_init() has not been called yet, so the
refcount and the fence ops are uninitialized. Calling dma_fence_put() on
such an object leads to undefined behavior.
Use kfree() instead, since the fence is just a plain allocation at this
stage, and rename the label to err_fence_free to reflect the actual
cleanup action. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject writes through untrusted BTF pointers
check_ptr_to_btf_access() lets program-type btf_struct_access callbacks
validate writes before the default BTF access path rejects non-read
accesses. That bypasses the read-only policy for untrusted BTF pointers
created by helpers such as bpf_rdonly_cast().
Reject non-read accesses through PTR_UNTRUSTED BTF pointers at the
common entry point, before the callback branch to handle all cases. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/pm/powerplay: bounds-check voltage index in SMU7 lookup
vddInd and vddcInd fields from VBIOS-parsed tables are used to index into
voltage lookup tables without a bounds check. Return -EINVAL when any
index is out of range. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: core: quiesce input in hid_hw_stop() to prevent use-after-free
A driver's probe calls hid_device_io_start() to enable input delivery,
then fails at a later initialization step and unwinds via hid_hw_stop().
The unwind frees struct hidraw via hidraw_disconnect() while in-flight
HID reports may still be running on another CPU, dereferencing the
freed object through hidraw_report_event(). syzbot reports the
resulting use-after-free for the corsair-psu HID driver.
Edward Adam Davis posted a per-driver fix for corsair-psu that adds
an explicit hid_device_io_stop() before hid_hw_stop() in the probe
error path ("hwmon: prevent packets from going to driver for probe",
2026-04-28). Auditing the tree shows 15 drivers call
hid_device_io_start(); 7 also call hid_device_io_stop() and 8 do not:
drivers calling hid_device_io_start() without a matching
hid_device_io_stop() before hid_hw_stop():
drivers/hwmon/corsair-psu.c (fix posted by Edward)
drivers/hwmon/corsair-cpro.c
drivers/hwmon/nzxt-kraken3.c
drivers/hwmon/nzxt-smart2.c
drivers/hwmon/gigabyte_waterforce.c
drivers/hid/hid-logitech-dj.c
drivers/hid/hid-nintendo.c
drivers/hid/hid-mcp2221.c
Roughly half of all callers of the API are exposed. Centralize the
quiesce in hid_hw_stop() so callers do not have to remember the
matching stop: if a driver has left hdev->io_started true on entry,
call hid_device_io_stop() before hid_disconnect().
For the 7 drivers that already call hid_device_io_stop() correctly,
hdev->io_started is false on entry, the guard short-circuits, and
behavior is unchanged.
No Fixes: tag because the affected drivers gained their
hid_device_io_start() calls independently over years; the bug is a
class-wide API misuse rather than a regression from one commit. |
