Export limit exceeded: 421005 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (421005 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-72096 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: dm-verity: make error counter atomic The error counter "v->corrupted_errs" was not atomic, thus it could be subject to race conditions. The call to dm_audit_log_target("max-corrupted-errors") may be skipped due to the races. | ||||
| CVE-2026-72088 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: scsi: hpsa: Fix DMA mapping leak on IOACCEL2 reset path If phys_disk->in_reset is set, the function returns directly without undoing the resources acquired for the command. Add the missing error cleanup by unmapping the IOACCEL2 SG chain block when needed, unmapping the SCSI command, and dropping the outstanding IOACCEL command count before returning. | ||||
| CVE-2026-72087 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Fix memory leak in lpfc_sli4_driver_resource_setup() The memory allocated for mboxq using mempool_alloc() is not freed in some of the early exit error paths. Fix that by moving the mempool_free() call to an earlier point after last use. | ||||
| CVE-2026-72086 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: scsi: xen: scsiback: Free the command tag on the TMR submit-failure path scsiback_device_action() obtains a command tag in scsiback_get_pend_req() and submits a task-management request with target_submit_tmr(). When target_submit_tmr() fails it returns < 0 and scsiback jumps to the err: label, which sends a response but frees nothing, leaking the tag. Impact: a pvSCSI guest can leak the command tags of a LUN's session, stopping the LUN, by issuing VSCSIIF_ACT_SCSI_ABORT or RESET requests whenever target_submit_tmr() fails. transport_generic_free_cmd() cannot be used here. By the time target_submit_tmr() returns an error it has already run __target_init_cmd() (so se_cmd->cmd_kref is one, not zero), and on its target_get_sess_cmd() error path it has freed se_cmd->se_tmr_req via core_tmr_release_req() while leaving SCF_SCSI_TMR_CDB set and the pointer dangling. Letting the command release run target_free_cmd_mem() would then double-free se_tmr_req. Use the same helper, which returns just the tag, on this path too. | ||||
| CVE-2026-72073 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: mmc: vub300: fix use-after-free on probe failure The vub300 driver lifetime-manages its controller state using vub300->kref, with vub300_delete() freeing the mmc host when the last reference is dropped. The probe error path after the inactivity timer has been armed still bypasses that lifetime rule, however, and falls through to mmc_free_host() directly if mmc_add_host() fails. The race window is between arming the inactivity timer and reaching the probe error unwind after mmc_add_host() fails: probe thread timer/workqueue ------------ --------------- kref_init(&vub300->kref) ref = 1 kref_get(&vub300->kref) ref = 2, timer ref add_timer(inactivity_timer) fires after one second | | race window |<----------------------------------------------------> | mmc_add_host(mmc) inactivity timer fires vub300_queue_dead_work() kref_get() ref = 3 queue_work(deadwork) mmc_add_host() fails timer_delete_sync() mmc_free_host(mmc) frees vub300 deadwork runs use-after-free The inactivity timeout is one second, so this would require mmc_add_host() to both fail and take more than one second to do so. This is unlikely to happen in practice, but the error path is still wrong. timer_delete_sync() only waits for the timer callback itself. It does not flush deadwork that the callback may already have queued. As a result, queued deadwork can still hold a kref while the probe error path directly frees the backing mmc host, including the vub300 storage. Fix this by using the same lifetime mechanism as disconnect. Clear vub300->interface so that the timer callback and any queued deadwork return early and drop their references, then drop the initial probe reference and return without falling through to err_free_host. | ||||
| CVE-2026-72070 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: libertas_tf: fix use-after-free in lbtf_free_adapter() lbtf_free_adapter() calls timer_delete(&priv->command_timer), which does not wait for a running command_timer_fn() callback. lbtf_free_adapter() runs on the teardown path right before ieee80211_free_hw() frees priv, both in lbtf_remove_card() and in the probe error path. command_timer is armed by mod_timer() in lbtf_cmd() whenever a firmware command is sent. command_timer_fn() dereferences priv. If a command times out as the device is removed, command_timer_fn() runs concurrently with teardown and dereferences priv after it has been freed. This is the same use-after-free that commit 03cc8f90d053 ("wifi: libertas: fix use-after-free in lbs_free_adapter()") fixed in the sibling libertas driver. The libertas_tf variant has the identical pattern and was left unchanged. Use timer_delete_sync() so any in-flight callback completes before priv is freed. | ||||
| CVE-2026-72068 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: posix-cpu-timers: Use u64 multiplication in update_rlimit_cpu() update_rlimit_cpu() converts the RLIMIT_CPU value to nanoseconds with u64 nsecs = rlim_new * NSEC_PER_SEC; On 32-bit kernels both rlim_new (unsigned long) and NSEC_PER_SEC (1000000000L) are 32-bit, so the multiplication is performed in unsigned long and truncated for rlim_new > 4 seconds before being widened to u64. The same file already casts to u64 for the matching computation in check_process_timers(): u64 softns = (u64)soft * NSEC_PER_SEC; As a result, the truncated value is installed into the CPUCLOCK_PROF expiry cache (nextevt), causing the process CPU timer to be programmed to fire prematurely for any RLIMIT_CPU soft limit >= 5 seconds. The actual SIGXCPU/SIGKILL decision in check_process_timers() already casts to u64 and is therefore correct, so limit enforcement is not broken; only the expiry-cache programming is wrong. Apply the same cast here so both paths convert rlim_cur identically. 64-bit kernels are unaffected. | ||||
| CVE-2026-72063 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: gpio: tegra: do not call pinctrl for GPIO direction tegra_gpio_direction_input() and tegra_gpio_direction_output() already program the GPIO controller direction registers directly. The additional pinctrl_gpio_direction_input/output() calls do not add a Tegra pinctrl operation, because the Tegra pinmux ops provide GPIO request/free handling but no gpio_set_direction hook. The extra call still enters the pinctrl core and takes pctldev->mutex. Shared GPIO users can call the direction path while holding their per-line spinlock, so this otherwise redundant pinctrl direction call can sleep in an atomic context. This was found by our static analysis tool and then confirmed by manual review of tegra_gpio_probe(), the Tegra GPIO direction callbacks and the Tegra pinctrl ops. The reviewed path has a default non-sleeping struct gpio_chip while the direction callback still enters the pinctrl mutex path. A directed runtime validation kept the same non-sleeping chip registration and drove: gpio_shared_proxy_direction_output() gpiod_direction_output_raw_commit() tegra_gpio_direction_output() pinctrl_gpio_direction_output() Lockdep reported a sleep-in-atomic warning with the shared GPIO spinlock held and pinctrl_get_device_gpio_range() plus tegra_gpio_direction_output() on the stack. Do not mark the whole chip as can_sleep to paper over this: can_sleep describes whether get()/set() may sleep, and Tegra value access is MMIO. Remove the redundant pinctrl direction calls and keep pinctrl involvement in the existing request/free path. | ||||
| CVE-2026-72056 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net: ena: clean up XDP TX queues when regular TX setup fails create_queues_with_size_backoff() creates XDP TX queues before setting up the regular TX path. If the subsequent allocation or creation of regular TX queues fails, the error handling paths omit the teardown of the XDP TX queues, leading to a resource leak. Fix this by explicitly destroying the XDP TX queue subset at the two missing failure points. The bug was first flagged by an experimental analysis tool we are developing for kernel memory-management bugs while analyzing v6.13-rc1. The tool is still under development and is not yet publicly available. Manual inspection confirms that the bug is still present in v7.1-rc7. An x86_64 allyesconfig build showed no new warnings. As we do not have an ENA device to test with, no runtime testing was able to be performed. | ||||
| CVE-2026-72040 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ipmi: fix refcount leak in i_ipmi_request() When a caller provides a `supplied_recv` message to i_ipmi_request(), the function increments the user's `nr_msgs` reference count. If an error occurs later, the out_err cleanup path only frees the recv_msg if the function allocated it itself (i.e., !supplied_recv). In the supplied_recv case the cleanup is skipped, leaving the reference count elevated. The caller ipmi_request_supply_msgs() does not release the supplied_recv on error, so the reference is permanently leaked. Fix this by explicitly reverting the reference count operations when a supplied recv_msg with a valid user pointer is present in the error path: decrement nr_msgs and drop the user's kref. | ||||
| CVE-2026-72039 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: bnx2x: fix potential memory leak in bnx2x_alloc_mem_bp() If the allocation of fp[i].tpa_info fails, the error path will not free the struct bnx2x_fastpath allocated earlier, as it is not linked to the bp structure yet. Fix that by linking it immediately after allocation. | ||||
| CVE-2026-72030 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ata: libata-core: Reject an invalid concurrent positioning ranges count ata_dev_config_cpr() takes the number of range descriptors from buf[0] of the concurrent positioning ranges log (up to 255), which the device reports independently of the log size in the GPL directory. The count is then walked at a fixed 32-byte stride in two places with no bound: the log read here, and the INQUIRY VPD page B9h emitter, which writes one descriptor per range into the fixed 2048-byte ata_scsi_rbuf. A device reporting a count larger than its own log overflows the read buffer (up to 7704 bytes past a 512-byte slab), and a count above 62 overflows the response buffer on the emit side. Bound the count once, on probe, against both the log the device returned and the number of descriptors the VPD B9h response buffer can hold (ATA_DEV_MAX_CPR, derived from the rbuf size). Reject an out-of-range count with a warning; this keeps the emitter in bounds with no separate change there. | ||||
| CVE-2026-72015 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: fs/resctrl: Fix double-add of pseudo-locked region's RMID to free list A pseudo-locked group's RMID is freed when it is created. On unmount rmdir_all_sub() unconditionally frees all RMID of all groups, resulting in a double-free of the pseudo-locked group's RMID. The consequence of this is that the original free results in the pseudo-locked group's RMID being added to the rmid_free_lru linked list and the second free then attempts to add the same RMID entry to the rmid_free_lru again. Do not double-free a pseudo-locked group's RMID. | ||||
| CVE-2026-72010 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: cgroup/cpuset: rebind mm mempolicy to effective_mems, not mems_allowed Creating a child cpuset where cpuset.mems is never set leads to a div/0 when a VMA mempolicy with MPOL_F_RELATIVE_NODES rebinds in response to a CPU hotplug event. Reproduction steps: 1) Create a cgroup w/ cpuset controls (do not set cpuset.mems) 2) Move the task into the child cpuset 3) Create a VMA mempolicy for that task with MPOL_F_RELATIVE_NODES 4) unplug and hotplug a cpu echo 0 > /sys/devices/system/cpu/cpu1/online echo 1 > /sys/devices/system/cpu/cpu1/online 5) mempolicy rebind does a div/0 in mpol_relative_nodemask on the call to __nodes_fold() The cpuset code passes (cs->mems_allowed) which is not guaranteed to have nodes to the rebind routine. Use cs->effective_mems instead, which is guaranteed to have a non-empty nodemask once we reach that code path. [ david: add a comment, slightly rephrase description ] | ||||
| CVE-2026-72004 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: fix memory leak in ieee80211_register_hw() If kmemdup() fails while copying supported band structures, the error path jumps to fail_rate. This skips rate_control_deinitialize() and leaks the initialized local->rate_ctrl. Fix this by adding a fail_band label that shares the rate-control cleanup path before falling through to the remaining teardown. The bug was first flagged by an experimental analysis tool we are developing for kernel memory-management bugs while analyzing v6.13-rc1. The tool is still under development and is not yet publicly available. Manual inspection confirms that the bug is still present in v7.1-rc7. An x86_64 allyesconfig build showed no new warnings. As we do not have a suitable mac80211 device/driver combination to test with, no runtime testing was able to be performed. | ||||
| CVE-2026-68480 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 8.8 High |
| In the Linux kernel, the following vulnerability has been resolved: x86/bugs: Make Safe-RET robust against interrupt injection An attacker injecting interrupts while the Safe-RET mitigation executes on machines affected by SRSO can neutralize the safe return sequence, potentially leading to data leakage through speculative execution. Fixup register state as if the Safe-RET sequence executed successfully by "emulating" it, in a manner of speaking, and avoid executing a RET instruction after returning from the interrupt. | ||||
| CVE-2026-68475 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: reset: sunxi: fix memory region leak on ioremap failure In sunxi_reset_init(), when ioremap() fails, the memory region obtained via request_mem_region() is not released, leading to a resource leak. Add an err_mem_region label to properly release the memory region before freeing the data structure. | ||||
| CVE-2026-68469 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: fix permanently busy scans after multiple roam iterations In order for the firmware to sleep, the driver has to confirm a previously received sleep request. The normal sequence of evets goes like this: EVENT_SLEEP -> adapter->ps_state = PS_STATE_PRE_SLEEP -> sleep-confirm -> SLEEP -> EVENT_AWAKE -> AWAKE. Before sending the sleep-confirm command, the driver must make sure there are no commands either running or waiting to be completed. mwifiex_ret_802_11_associate() unconditionally sets ps_state = PS_STATE_AWAKE when it processes the association command response, outside of the normal powersave management flow. If EVENT_SLEEP arrives while the association command is in flight, ps_state is PRE_SLEEP when the association command response is parsed, and the forced AWAKE overwrites it. The deferred sleep-confirm is never sent. A subsequent scan_start command is correctly acknowledged, but the firmware doesn't generate scan_result events. The scan request never finishes, and additional requests from userspace fail with -EBUSY. After testing on both IW412 and W8997, I could only trigger the bug on the IW412 and observed the firmwares behave differently. On the IW412 the firmware still sends EVENT_SLEEP while the authentication / association process is ongoing. A W8997 under the same conditions seems to suppress power-save for the duration of the association, so PRE_SLEEP never coincided with the association response even after extended periods of testing using the loops described below (>12hours). On the IW412, the delay between commands that triggers an EVENT_SLEEP was empirically determined to be ~20ms. This delay can naturally occur when the driver is outputting debugging information (debug_mask = 0x00000037), in which situation the busy scans issue is repeatable while running "test 1)" as described below. If the delay between commands is less than ~20ms, the firmware stays awake and the issue was not reproducible running the same test. The host_mlme=false path also behaves differently. In this case, the entire authentication / association transaction is executed by one command (HostCmd_CMD_802_11_ASSOCIATE), and the firmware doesn't emit EVENT_SLEEP while the command is running. Remove the assignment so the ps_state is only manipulated in the paths that are related to powersave event handling and on the main workqueue for correct sleep confirmation. The following loop tests were performed (with debugging output enabled): 1) force roaming between two AP's, one 5GHz and one 2.4GHz, same SSID. Use wpa_cli to trigger the roaming behavior, sleep 2s between iterations. 2) force a disconnection to AP 1 and a connection to AP 2, test scan. Use wpa_cli to trigger the connection changes, sleep 2s between iterations. Each test ran in each device for at least 3 hours. | ||||
| CVE-2026-68456 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: usb: atm: ueagle-atm: wait for pre-firmware load in .disconnect() ueagle-atm uses the asynchronous request_firmware_nowait() in .probe(), but does not wait for its completion, not even in .disconnect(); so, if the device is unplugged meanwhile, its teardown runs concurrently with that. Even though this inconsistency is worth addressing on its own, it has also triggered several bug reports in syzbot over the years (some auto-closed) where the firmware sysfs fallback mechanism (CONFIG_FW_LOADER_USER_HELPER) creates a firmware subdirectory in the device directory during its removal, which might hit unexpected conditions in kernfs, apparently, depending at which point the add and remove operations raced. (See links.) The pattern is: usb ?-?: Direct firmware load for ueagle-atm/eagle?.fw failed with error -2 usb ?-?: Falling back to sysfs fallback for: ueagle-atm/eagle?.fw <ERROR> Call trace: ... kernfs_create_dir_ns sysfs_create_dir_ns create_dir kobject_add_internal kobject_add_varg kobject_add class_dir_create_and_add get_device_parent device_add fw_load_sysfs_fallback fw_load_from_user_helper firmware_fallback_sysfs _request_firmware request_firmware_work_func ... (Some variations are observed, after fw_load_sysfs_fallback(), e.g., [1].) While the kernfs side is being looked at, the ueagle-atm side can be fixed by waiting for the pre-firmware load in the .disconnect() handler. This change has a similar approach to previous work by Andrey Tsygunka [2] (wait_for_completion() in .disconnect()), but it is relatively different in design/implementation; using the Originally-by tag for credit assignment. This has been tested with: - synthetic reproducer to check the error path; - USB gadget (virtual device) to check the firmware upload path; - QEMU device emulator to check the device ID re-enumeration path; (The latter two were written by Claude; no other code/text in this commit.) Links (year first reported): 2025 https://syzbot.org/bug?extid=ce1e5a1b4e086b43e56d 2025 https://syzbot.org/bug?extid=9af8471255ac36e34fd4 2024 https://syzbot.org/bug?extid=306212936b13e520679d 2023 https://syzkaller.appspot.com/bug?extid=457452d30bcdda75ead2 2022 https://syzbot.org/bug?extid=782984d6f1701b526edb 2021 https://syzbot.org/bug?id=f3f221579f4ef7e9691281f3c6f56c05f83e8490 2021 https://syzbot.org/bug?id=84d86f0d71394829df6fc53daf6642c045983881 2021 https://syzbot.org/bug?id=3302dc1c0e2b9c94f2e8edb404eabc9267bc6f90 [1] https://syzkaller.appspot.com/bug?extid=457452d30bcdda75ead2 [2] https://lore.kernel.org/lkml/20250410093146.3776801-2-aitsygunka@yandex.ru/ | ||||
| CVE-2026-68450 | 1 Linux | 1 Linux Kernel | 2026-11-06 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: btrfs: free mapping node on duplicate reloc root insert __add_reloc_root() allocates a mapping_node before inserting it into rc->reloc_root_tree. If rb_simple_insert() finds an existing entry, it returns the existing rb_node and leaves the newly allocated node unlinked. The error path then returns -EEXIST without freeing the new node. Since the node was never inserted into reloc_root_tree, the later cleanup in put_reloc_control() cannot find it either. Free the newly allocated node before returning -EEXIST. The callers currently assert that -EEXIST should not happen, so this is a defensive cleanup for an unexpected duplicate insert path. If the path is ever reached, the local allocation should still be released. | ||||