Filtered by vendor Linux
Subscriptions
Total
15909 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2024-35819 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: soc: fsl: qbman: Use raw spinlock for cgr_lock smp_call_function always runs its callback in hard IRQ context, even on PREEMPT_RT, where spinlocks can sleep. So we need to use a raw spinlock for cgr_lock to ensure we aren't waiting on a sleeping task. Although this bug has existed for a while, it was not apparent until commit ef2a8d5478b9 ("net: dpaa: Adjust queue depth on rate change") which invokes smp_call_function_single via qman_update_cgr_safe every time a link goes up or down. | ||||
| CVE-2024-35822 | 3 Debian, Linux, Redhat | 3 Debian Linux, Linux Kernel, Enterprise Linux | 2025-12-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: usb: udc: remove warning when queue disabled ep It is possible trigger below warning message from mass storage function, WARNING: CPU: 6 PID: 3839 at drivers/usb/gadget/udc/core.c:294 usb_ep_queue+0x7c/0x104 pc : usb_ep_queue+0x7c/0x104 lr : fsg_main_thread+0x494/0x1b3c Root cause is mass storage function try to queue request from main thread, but other thread may already disable ep when function disable. As there is no function failure in the driver, in order to avoid effort to fix warning, change WARN_ON_ONCE() in usb_ep_queue() to pr_debug(). | ||||
| CVE-2024-35825 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: usb: gadget: ncm: Fix handling of zero block length packets While connecting to a Linux host with CDC_NCM_NTB_DEF_SIZE_TX set to 65536, it has been observed that we receive short packets, which come at interval of 5-10 seconds sometimes and have block length zero but still contain 1-2 valid datagrams present. According to the NCM spec: "If wBlockLength = 0x0000, the block is terminated by a short packet. In this case, the USB transfer must still be shorter than dwNtbInMaxSize or dwNtbOutMaxSize. If exactly dwNtbInMaxSize or dwNtbOutMaxSize bytes are sent, and the size is a multiple of wMaxPacketSize for the given pipe, then no ZLP shall be sent. wBlockLength= 0x0000 must be used with extreme care, because of the possibility that the host and device may get out of sync, and because of test issues. wBlockLength = 0x0000 allows the sender to reduce latency by starting to send a very large NTB, and then shortening it when the sender discovers that there’s not sufficient data to justify sending a large NTB" However, there is a potential issue with the current implementation, as it checks for the occurrence of multiple NTBs in a single giveback by verifying if the leftover bytes to be processed is zero or not. If the block length reads zero, we would process the same NTB infintely because the leftover bytes is never zero and it leads to a crash. Fix this by bailing out if block length reads zero. | ||||
| CVE-2024-35830 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: media: tc358743: register v4l2 async device only after successful setup Ensure the device has been setup correctly before registering the v4l2 async device, thus allowing userspace to access. | ||||
| CVE-2024-35837 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net: mvpp2: clear BM pool before initialization Register value persist after booting the kernel using kexec which results in kernel panic. Thus clear the BM pool registers before initialisation to fix the issue. | ||||
| CVE-2025-38066 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: dm cache: prevent BUG_ON by blocking retries on failed device resumes A cache device failing to resume due to mapping errors should not be retried, as the failure leaves a partially initialized policy object. Repeating the resume operation risks triggering BUG_ON when reloading cache mappings into the incomplete policy object. Reproduce steps: 1. create a cache metadata consisting of 512 or more cache blocks, with some mappings stored in the first array block of the mapping array. Here we use cache_restore v1.0 to build the metadata. cat <<EOF >> cmeta.xml <superblock uuid="" block_size="128" nr_cache_blocks="512" \ policy="smq" hint_width="4"> <mappings> <mapping cache_block="0" origin_block="0" dirty="false"/> </mappings> </superblock> EOF dmsetup create cmeta --table "0 8192 linear /dev/sdc 0" cache_restore -i cmeta.xml -o /dev/mapper/cmeta --metadata-version=2 dmsetup remove cmeta 2. wipe the second array block of the mapping array to simulate data degradations. mapping_root=$(dd if=/dev/sdc bs=1c count=8 skip=192 \ 2>/dev/null | hexdump -e '1/8 "%u\n"') ablock=$(dd if=/dev/sdc bs=1c count=8 skip=$((4096*mapping_root+2056)) \ 2>/dev/null | hexdump -e '1/8 "%u\n"') dd if=/dev/zero of=/dev/sdc bs=4k count=1 seek=$ablock 3. try bringing up the cache device. The resume is expected to fail due to the broken array block. dmsetup create cmeta --table "0 8192 linear /dev/sdc 0" dmsetup create cdata --table "0 65536 linear /dev/sdc 8192" dmsetup create corig --table "0 524288 linear /dev/sdc 262144" dmsetup create cache --notable dmsetup load cache --table "0 524288 cache /dev/mapper/cmeta \ /dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 writethrough smq 0" dmsetup resume cache 4. try resuming the cache again. An unexpected BUG_ON is triggered while loading cache mappings. dmsetup resume cache Kernel logs: (snip) ------------[ cut here ]------------ kernel BUG at drivers/md/dm-cache-policy-smq.c:752! Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI CPU: 0 UID: 0 PID: 332 Comm: dmsetup Not tainted 6.13.4 #3 RIP: 0010:smq_load_mapping+0x3e5/0x570 Fix by disallowing resume operations for devices that failed the initial attempt. | ||||
| CVE-2025-38065 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: orangefs: Do not truncate file size 'len' is used to store the result of i_size_read(), so making 'len' a size_t results in truncation to 4GiB on 32-bit systems. | ||||
| CVE-2025-38063 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: dm: fix unconditional IO throttle caused by REQ_PREFLUSH When a bio with REQ_PREFLUSH is submitted to dm, __send_empty_flush() generates a flush_bio with REQ_OP_WRITE | REQ_PREFLUSH | REQ_SYNC, which causes the flush_bio to be throttled by wbt_wait(). An example from v5.4, similar problem also exists in upstream: crash> bt 2091206 PID: 2091206 TASK: ffff2050df92a300 CPU: 109 COMMAND: "kworker/u260:0" #0 [ffff800084a2f7f0] __switch_to at ffff80004008aeb8 #1 [ffff800084a2f820] __schedule at ffff800040bfa0c4 #2 [ffff800084a2f880] schedule at ffff800040bfa4b4 #3 [ffff800084a2f8a0] io_schedule at ffff800040bfa9c4 #4 [ffff800084a2f8c0] rq_qos_wait at ffff8000405925bc #5 [ffff800084a2f940] wbt_wait at ffff8000405bb3a0 #6 [ffff800084a2f9a0] __rq_qos_throttle at ffff800040592254 #7 [ffff800084a2f9c0] blk_mq_make_request at ffff80004057cf38 #8 [ffff800084a2fa60] generic_make_request at ffff800040570138 #9 [ffff800084a2fae0] submit_bio at ffff8000405703b4 #10 [ffff800084a2fb50] xlog_write_iclog at ffff800001280834 [xfs] #11 [ffff800084a2fbb0] xlog_sync at ffff800001280c3c [xfs] #12 [ffff800084a2fbf0] xlog_state_release_iclog at ffff800001280df4 [xfs] #13 [ffff800084a2fc10] xlog_write at ffff80000128203c [xfs] #14 [ffff800084a2fcd0] xlog_cil_push at ffff8000012846dc [xfs] #15 [ffff800084a2fda0] xlog_cil_push_work at ffff800001284a2c [xfs] #16 [ffff800084a2fdb0] process_one_work at ffff800040111d08 #17 [ffff800084a2fe00] worker_thread at ffff8000401121cc #18 [ffff800084a2fe70] kthread at ffff800040118de4 After commit 2def2845cc33 ("xfs: don't allow log IO to be throttled"), the metadata submitted by xlog_write_iclog() should not be throttled. But due to the existence of the dm layer, throttling flush_bio indirectly causes the metadata bio to be throttled. Fix this by conditionally adding REQ_IDLE to flush_bio.bi_opf, which makes wbt_should_throttle() return false to avoid wbt_wait(). | ||||
| CVE-2025-38001 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net_sched: hfsc: Address reentrant enqueue adding class to eltree twice Savino says: "We are writing to report that this recent patch (141d34391abbb315d68556b7c67ad97885407547) [1] can be bypassed, and a UAF can still occur when HFSC is utilized with NETEM. The patch only checks the cl->cl_nactive field to determine whether it is the first insertion or not [2], but this field is only incremented by init_vf [3]. By using HFSC_RSC (which uses init_ed) [4], it is possible to bypass the check and insert the class twice in the eltree. Under normal conditions, this would lead to an infinite loop in hfsc_dequeue for the reasons we already explained in this report [5]. However, if TBF is added as root qdisc and it is configured with a very low rate, it can be utilized to prevent packets from being dequeued. This behavior can be exploited to perform subsequent insertions in the HFSC eltree and cause a UAF." To fix both the UAF and the infinite loop, with netem as an hfsc child, check explicitly in hfsc_enqueue whether the class is already in the eltree whenever the HFSC_RSC flag is set. [1] https://web.git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=141d34391abbb315d68556b7c67ad97885407547 [2] https://elixir.bootlin.com/linux/v6.15-rc5/source/net/sched/sch_hfsc.c#L1572 [3] https://elixir.bootlin.com/linux/v6.15-rc5/source/net/sched/sch_hfsc.c#L677 [4] https://elixir.bootlin.com/linux/v6.15-rc5/source/net/sched/sch_hfsc.c#L1574 [5] https://lore.kernel.org/netdev/8DuRWwfqjoRDLDmBMlIfbrsZg9Gx50DHJc1ilxsEBNe2D6NMoigR_eIRIG0LOjMc3r10nUUZtArXx4oZBIdUfZQrwjcQhdinnMis_0G7VEk=@willsroot.io/T/#u | ||||
| CVE-2025-38074 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: vhost-scsi: protect vq->log_used with vq->mutex The vhost-scsi completion path may access vq->log_base when vq->log_used is already set to false. vhost-thread QEMU-thread vhost_scsi_complete_cmd_work() -> vhost_add_used() -> vhost_add_used_n() if (unlikely(vq->log_used)) QEMU disables vq->log_used via VHOST_SET_VRING_ADDR. mutex_lock(&vq->mutex); vq->log_used = false now! mutex_unlock(&vq->mutex); QEMU gfree(vq->log_base) log_used() -> log_write(vq->log_base) Assuming the VMM is QEMU. The vq->log_base is from QEMU userpace and can be reclaimed via gfree(). As a result, this causes invalid memory writes to QEMU userspace. The control queue path has the same issue. | ||||
| CVE-2025-38072 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: libnvdimm/labels: Fix divide error in nd_label_data_init() If a faulty CXL memory device returns a broken zero LSA size in its memory device information (Identify Memory Device (Opcode 4000h), CXL spec. 3.1, 8.2.9.9.1.1), a divide error occurs in the libnvdimm driver: Oops: divide error: 0000 [#1] PREEMPT SMP NOPTI RIP: 0010:nd_label_data_init+0x10e/0x800 [libnvdimm] Code and flow: 1) CXL Command 4000h returns LSA size = 0 2) config_size is assigned to zero LSA size (CXL pmem driver): drivers/cxl/pmem.c: .config_size = mds->lsa_size, 3) max_xfer is set to zero (nvdimm driver): drivers/nvdimm/label.c: max_xfer = min_t(size_t, ndd->nsarea.max_xfer, config_size); 4) A subsequent DIV_ROUND_UP() causes a division by zero: drivers/nvdimm/label.c: /* Make our initial read size a multiple of max_xfer size */ drivers/nvdimm/label.c: read_size = min(DIV_ROUND_UP(read_size, max_xfer) * max_xfer, drivers/nvdimm/label.c- config_size); Fix this by checking the config size parameter by extending an existing check. | ||||
| CVE-2025-38071 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: x86/mm: Check return value from memblock_phys_alloc_range() At least with CONFIG_PHYSICAL_START=0x100000, if there is < 4 MiB of contiguous free memory available at this point, the kernel will crash and burn because memblock_phys_alloc_range() returns 0 on failure, which leads memblock_phys_free() to throw the first 4 MiB of physical memory to the wolves. At a minimum it should fail gracefully with a meaningful diagnostic, but in fact everything seems to work fine without the weird reserve allocation. | ||||
| CVE-2025-38068 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: crypto: lzo - Fix compression buffer overrun Unlike the decompression code, the compression code in LZO never checked for output overruns. It instead assumes that the caller always provides enough buffer space, disregarding the buffer length provided by the caller. Add a safe compression interface that checks for the end of buffer before each write. Use the safe interface in crypto/lzo. | ||||
| CVE-2025-38067 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: rseq: Fix segfault on registration when rseq_cs is non-zero The rseq_cs field is documented as being set to 0 by user-space prior to registration, however this is not currently enforced by the kernel. This can result in a segfault on return to user-space if the value stored in the rseq_cs field doesn't point to a valid struct rseq_cs. The correct solution to this would be to fail the rseq registration when the rseq_cs field is non-zero. However, some older versions of glibc will reuse the rseq area of previous threads without clearing the rseq_cs field and will also terminate the process if the rseq registration fails in a secondary thread. This wasn't caught in testing because in this case the leftover rseq_cs does point to a valid struct rseq_cs. What we can do is clear the rseq_cs field on registration when it's non-zero which will prevent segfaults on registration and won't break the glibc versions that reuse rseq areas on thread creation. | ||||
| CVE-2025-38120 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_set_pipapo_avx2: fix initial map fill If the first field doesn't cover the entire start map, then we must zero out the remainder, else we leak those bits into the next match round map. The early fix was incomplete and did only fix up the generic C implementation. A followup patch adds a test case to nft_concat_range.sh. | ||||
| CVE-2025-38118 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: MGMT: Fix UAF on mgmt_remove_adv_monitor_complete This reworks MGMT_OP_REMOVE_ADV_MONITOR to not use mgmt_pending_add to avoid crashes like bellow: ================================================================== BUG: KASAN: slab-use-after-free in mgmt_remove_adv_monitor_complete+0xe5/0x540 net/bluetooth/mgmt.c:5406 Read of size 8 at addr ffff88801c53f318 by task kworker/u5:5/5341 CPU: 0 UID: 0 PID: 5341 Comm: kworker/u5:5 Not tainted 6.15.0-syzkaller-10402-g4cb6c8af8591 #0 PREEMPT(full) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:408 [inline] print_report+0xd2/0x2b0 mm/kasan/report.c:521 kasan_report+0x118/0x150 mm/kasan/report.c:634 mgmt_remove_adv_monitor_complete+0xe5/0x540 net/bluetooth/mgmt.c:5406 hci_cmd_sync_work+0x261/0x3a0 net/bluetooth/hci_sync.c:334 process_one_work kernel/workqueue.c:3238 [inline] process_scheduled_works+0xade/0x17b0 kernel/workqueue.c:3321 worker_thread+0x8a0/0xda0 kernel/workqueue.c:3402 kthread+0x711/0x8a0 kernel/kthread.c:464 ret_from_fork+0x3fc/0x770 arch/x86/kernel/process.c:148 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 </TASK> Allocated by task 5987: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3e/0x80 mm/kasan/common.c:68 poison_kmalloc_redzone mm/kasan/common.c:377 [inline] __kasan_kmalloc+0x93/0xb0 mm/kasan/common.c:394 kasan_kmalloc include/linux/kasan.h:260 [inline] __kmalloc_cache_noprof+0x230/0x3d0 mm/slub.c:4358 kmalloc_noprof include/linux/slab.h:905 [inline] kzalloc_noprof include/linux/slab.h:1039 [inline] mgmt_pending_new+0x65/0x240 net/bluetooth/mgmt_util.c:252 mgmt_pending_add+0x34/0x120 net/bluetooth/mgmt_util.c:279 remove_adv_monitor+0x103/0x1b0 net/bluetooth/mgmt.c:5454 hci_mgmt_cmd+0x9c9/0xef0 net/bluetooth/hci_sock.c:1719 hci_sock_sendmsg+0x6ca/0xef0 net/bluetooth/hci_sock.c:1839 sock_sendmsg_nosec net/socket.c:712 [inline] __sock_sendmsg+0x219/0x270 net/socket.c:727 sock_write_iter+0x258/0x330 net/socket.c:1131 new_sync_write fs/read_write.c:593 [inline] vfs_write+0x548/0xa90 fs/read_write.c:686 ksys_write+0x145/0x250 fs/read_write.c:738 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f Freed by task 5989: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3e/0x80 mm/kasan/common.c:68 kasan_save_free_info+0x46/0x50 mm/kasan/generic.c:576 poison_slab_object mm/kasan/common.c:247 [inline] __kasan_slab_free+0x62/0x70 mm/kasan/common.c:264 kasan_slab_free include/linux/kasan.h:233 [inline] slab_free_hook mm/slub.c:2380 [inline] slab_free mm/slub.c:4642 [inline] kfree+0x18e/0x440 mm/slub.c:4841 mgmt_pending_foreach+0xc9/0x120 net/bluetooth/mgmt_util.c:242 mgmt_index_removed+0x10d/0x2f0 net/bluetooth/mgmt.c:9366 hci_sock_bind+0xbe9/0x1000 net/bluetooth/hci_sock.c:1314 __sys_bind_socket net/socket.c:1810 [inline] __sys_bind+0x2c3/0x3e0 net/socket.c:1841 __do_sys_bind net/socket.c:1846 [inline] __se_sys_bind net/socket.c:1844 [inline] __x64_sys_bind+0x7a/0x90 net/socket.c:1844 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f | ||||
| CVE-2025-38113 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ACPI: CPPC: Fix NULL pointer dereference when nosmp is used With nosmp in cmdline, other CPUs are not brought up, leaving their cpc_desc_ptr NULL. CPU0's iteration via for_each_possible_cpu() dereferences these NULL pointers, causing panic. Panic backtrace: [ 0.401123] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000b8 ... [ 0.403255] [<ffffffff809a5818>] cppc_allow_fast_switch+0x6a/0xd4 ... Kernel panic - not syncing: Attempted to kill init! [ rjw: New subject ] | ||||
| CVE-2025-38052 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: net/tipc: fix slab-use-after-free Read in tipc_aead_encrypt_done Syzbot reported a slab-use-after-free with the following call trace: ================================================================== BUG: KASAN: slab-use-after-free in tipc_aead_encrypt_done+0x4bd/0x510 net/tipc/crypto.c:840 Read of size 8 at addr ffff88807a733000 by task kworker/1:0/25 Call Trace: kasan_report+0xd9/0x110 mm/kasan/report.c:601 tipc_aead_encrypt_done+0x4bd/0x510 net/tipc/crypto.c:840 crypto_request_complete include/crypto/algapi.h:266 aead_request_complete include/crypto/internal/aead.h:85 cryptd_aead_crypt+0x3b8/0x750 crypto/cryptd.c:772 crypto_request_complete include/crypto/algapi.h:266 cryptd_queue_worker+0x131/0x200 crypto/cryptd.c:181 process_one_work+0x9fb/0x1b60 kernel/workqueue.c:3231 Allocated by task 8355: kzalloc_noprof include/linux/slab.h:778 tipc_crypto_start+0xcc/0x9e0 net/tipc/crypto.c:1466 tipc_init_net+0x2dd/0x430 net/tipc/core.c:72 ops_init+0xb9/0x650 net/core/net_namespace.c:139 setup_net+0x435/0xb40 net/core/net_namespace.c:343 copy_net_ns+0x2f0/0x670 net/core/net_namespace.c:508 create_new_namespaces+0x3ea/0xb10 kernel/nsproxy.c:110 unshare_nsproxy_namespaces+0xc0/0x1f0 kernel/nsproxy.c:228 ksys_unshare+0x419/0x970 kernel/fork.c:3323 __do_sys_unshare kernel/fork.c:3394 Freed by task 63: kfree+0x12a/0x3b0 mm/slub.c:4557 tipc_crypto_stop+0x23c/0x500 net/tipc/crypto.c:1539 tipc_exit_net+0x8c/0x110 net/tipc/core.c:119 ops_exit_list+0xb0/0x180 net/core/net_namespace.c:173 cleanup_net+0x5b7/0xbf0 net/core/net_namespace.c:640 process_one_work+0x9fb/0x1b60 kernel/workqueue.c:3231 After freed the tipc_crypto tx by delete namespace, tipc_aead_encrypt_done may still visit it in cryptd_queue_worker workqueue. I reproduce this issue by: ip netns add ns1 ip link add veth1 type veth peer name veth2 ip link set veth1 netns ns1 ip netns exec ns1 tipc bearer enable media eth dev veth1 ip netns exec ns1 tipc node set key this_is_a_master_key master ip netns exec ns1 tipc bearer disable media eth dev veth1 ip netns del ns1 The key of reproduction is that, simd_aead_encrypt is interrupted, leading to crypto_simd_usable() return false. Thus, the cryptd_queue_worker is triggered, and the tipc_crypto tx will be visited. tipc_disc_timeout tipc_bearer_xmit_skb tipc_crypto_xmit tipc_aead_encrypt crypto_aead_encrypt // encrypt() simd_aead_encrypt // crypto_simd_usable() is false child = &ctx->cryptd_tfm->base; simd_aead_encrypt crypto_aead_encrypt // encrypt() cryptd_aead_encrypt_enqueue cryptd_aead_enqueue cryptd_enqueue_request // trigger cryptd_queue_worker queue_work_on(smp_processor_id(), cryptd_wq, &cpu_queue->work) Fix this by holding net reference count before encrypt. | ||||
| CVE-2025-38051 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: smb: client: Fix use-after-free in cifs_fill_dirent There is a race condition in the readdir concurrency process, which may access the rsp buffer after it has been released, triggering the following KASAN warning. ================================================================== BUG: KASAN: slab-use-after-free in cifs_fill_dirent+0xb03/0xb60 [cifs] Read of size 4 at addr ffff8880099b819c by task a.out/342975 CPU: 2 UID: 0 PID: 342975 Comm: a.out Not tainted 6.15.0-rc6+ #240 PREEMPT(full) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x53/0x70 print_report+0xce/0x640 kasan_report+0xb8/0xf0 cifs_fill_dirent+0xb03/0xb60 [cifs] cifs_readdir+0x12cb/0x3190 [cifs] iterate_dir+0x1a1/0x520 __x64_sys_getdents+0x134/0x220 do_syscall_64+0x4b/0x110 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f996f64b9f9 Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0d f7 c3 0c 00 f7 d8 64 89 8 RSP: 002b:00007f996f53de78 EFLAGS: 00000207 ORIG_RAX: 000000000000004e RAX: ffffffffffffffda RBX: 00007f996f53ecdc RCX: 00007f996f64b9f9 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003 RBP: 00007f996f53dea0 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000207 R12: ffffffffffffff88 R13: 0000000000000000 R14: 00007ffc8cd9a500 R15: 00007f996f51e000 </TASK> Allocated by task 408: kasan_save_stack+0x20/0x40 kasan_save_track+0x14/0x30 __kasan_slab_alloc+0x6e/0x70 kmem_cache_alloc_noprof+0x117/0x3d0 mempool_alloc_noprof+0xf2/0x2c0 cifs_buf_get+0x36/0x80 [cifs] allocate_buffers+0x1d2/0x330 [cifs] cifs_demultiplex_thread+0x22b/0x2690 [cifs] kthread+0x394/0x720 ret_from_fork+0x34/0x70 ret_from_fork_asm+0x1a/0x30 Freed by task 342979: kasan_save_stack+0x20/0x40 kasan_save_track+0x14/0x30 kasan_save_free_info+0x3b/0x60 __kasan_slab_free+0x37/0x50 kmem_cache_free+0x2b8/0x500 cifs_buf_release+0x3c/0x70 [cifs] cifs_readdir+0x1c97/0x3190 [cifs] iterate_dir+0x1a1/0x520 __x64_sys_getdents64+0x134/0x220 do_syscall_64+0x4b/0x110 entry_SYSCALL_64_after_hwframe+0x76/0x7e The buggy address belongs to the object at ffff8880099b8000 which belongs to the cache cifs_request of size 16588 The buggy address is located 412 bytes inside of freed 16588-byte region [ffff8880099b8000, ffff8880099bc0cc) The buggy address belongs to the physical page: page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x99b8 head: order:3 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0 anon flags: 0x80000000000040(head|node=0|zone=1) page_type: f5(slab) raw: 0080000000000040 ffff888001e03400 0000000000000000 dead000000000001 raw: 0000000000000000 0000000000010001 00000000f5000000 0000000000000000 head: 0080000000000040 ffff888001e03400 0000000000000000 dead000000000001 head: 0000000000000000 0000000000010001 00000000f5000000 0000000000000000 head: 0080000000000003 ffffea0000266e01 00000000ffffffff 00000000ffffffff head: ffffffffffffffff 0000000000000000 00000000ffffffff 0000000000000008 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8880099b8080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8880099b8100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff8880099b8180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff8880099b8200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8880099b8280: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== POC is available in the link [1]. The problem triggering process is as follows: Process 1 Process 2 ----------------------------------- ---truncated--- | ||||
| CVE-2025-38048 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-12-17 | 4.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: virtio_ring: Fix data race by tagging event_triggered as racy for KCSAN syzbot reports a data-race when accessing the event_triggered, here is the simplified stack when the issue occurred: ================================================================== BUG: KCSAN: data-race in virtqueue_disable_cb / virtqueue_enable_cb_delayed write to 0xffff8881025bc452 of 1 bytes by task 3288 on cpu 0: virtqueue_enable_cb_delayed+0x42/0x3c0 drivers/virtio/virtio_ring.c:2653 start_xmit+0x230/0x1310 drivers/net/virtio_net.c:3264 __netdev_start_xmit include/linux/netdevice.h:5151 [inline] netdev_start_xmit include/linux/netdevice.h:5160 [inline] xmit_one net/core/dev.c:3800 [inline] read to 0xffff8881025bc452 of 1 bytes by interrupt on cpu 1: virtqueue_disable_cb_split drivers/virtio/virtio_ring.c:880 [inline] virtqueue_disable_cb+0x92/0x180 drivers/virtio/virtio_ring.c:2566 skb_xmit_done+0x5f/0x140 drivers/net/virtio_net.c:777 vring_interrupt+0x161/0x190 drivers/virtio/virtio_ring.c:2715 __handle_irq_event_percpu+0x95/0x490 kernel/irq/handle.c:158 handle_irq_event_percpu kernel/irq/handle.c:193 [inline] value changed: 0x01 -> 0x00 ================================================================== When the data race occurs, the function virtqueue_enable_cb_delayed() sets event_triggered to false, and virtqueue_disable_cb_split/packed() reads it as false due to the race condition. Since event_triggered is an unreliable hint used for optimization, this should only cause the driver temporarily suggest that the device not send an interrupt notification when the event index is used. Fix this KCSAN reported data-race issue by explicitly tagging the access as data_racy. | ||||