| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/sysfs: Add lockdown checks to legacy I/O and memory handlers
Currently, the legacy I/O and memory sysfs handlers do not check
security_locked_down(LOCKDOWN_PCI_ACCESS), leaving the legacy_io and
legacy_mem files unprotected when the kernel is locked down.
Commit eb627e17727e ("PCI: Lock down BAR access when the kernel is locked
down") added the check to pci_write_config(), pci_mmap_resource(), and
pci_write_resource_io() to prevent userspace from programming DMA-capable
hardware that could be used to modify kernel code, but did not cover the
legacy handlers.
As a result, root can still write arbitrary I/O ports and map the legacy
I/O and memory spaces while the kernel is locked down, which is the same
capability the lockdown is meant to remove.
Add the same check to pci_write_legacy_io(), pci_mmap_legacy_mem(), and
pci_mmap_legacy_io().
These generic handlers cover both architectures that define HAVE_PCI_LEGACY
(such as Alpha and PowerPC).
[bhelgaas: add Link] |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: cancel reset and rc work on device unregister
Both drivers cancelled dump_work on unregister but left reset_work and
rc_work to be flushed only by destroy_workqueue() in mt76_free_device(),
which runs after the hw is unregistered and the hardware stopped. A
reset_work that fires in that window calls ieee80211_restart_hw() and
re-arms mac_work on an unregistered hw, and rc_work touches station state
being torn down. Cancel both up front, alongside dump_work. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: bound TLV walk in mt7996_mcu_get_chip_config
The response TLV loop advanced by tlv->len without a minimum, so a
theoretical firmware response containing a zero-length TLV could spin
forever, hanging the CPU during device probe.
The u32 payload was also read without bounds checking.
Reject a short fixed field, stop on a TLV whose length underruns the
header or overruns the skb. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: fix RXDMAD_C buffer recycling race
The RXDMAD_C buffers come from the RRO data queues' page pools, which are
bound to a different NAPI, so the direct page-pool recycle used here could
race the owning NAPI; take the non-direct path as is already done for WED
RX queues. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: fix RX data queuing of RRO 3.0
For RRO 3.0, RX data released from a RRO data queue should be put to
the indicator queue. The frames are processed and completed in the
context of the indicator queue NAPI, which only polls skbs queued on
the MT_RXQ_RRO_IND list; frames queued under the data queue id are
left sitting on that list until the data queue NAPI happens to run,
stalling and reordering RX data. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt76x02: do not WARN on invalid rx descriptor length
The MPDU length in the rx descriptor comes from the hardware. In
monitor mode with the fcsfail filter enabled, the hardware passes up
corrupted frames, and a corrupted frame can report a length larger
than the received buffer. The bounds check correctly discards such
frames, but its WARN_ON_ONCE wrapper means any over-the-air garbage
frame taints the kernel, and panics it on the first such frame when
panic_on_warn is set.
Drop the WARN and discard the frame silently, matching what
commit c2d4c8723dbf ("mt76x2: remove some harmless WARN_ONs in tx
status and rx path") did for the neighboring rx and tx status paths.
Observed immediately on rx with an MT7612U in fcsfail monitor mode
on a busy channel. |
| In the Linux kernel, the following vulnerability has been resolved:
iomap: release the folio batch on iomap callback failures
A sashiko review of an unrelated patch points out that the folio
batch mechanism used for iomap zero range fails to release the batch
in a couple error scenarios. If either calls to ->iomap_end() or
->iomap_begin() fail, the direct return paths bypass the batch
cleanup.
The ->iomap_end() case is not a practical issue at the moment
because there is no user of the mechanism that returns an error from
this path. The ->iomap_begin() case is theoretically possible
because XFS can invoke the fill helper and error out at various
points thereafter. This subtly complicates things because XFS does
not transfer iomap_flags to the iomap data structure in the error
path.
To deal with both of these issues, first make sure to invoke the
cleanup helper in the error path for either fs callback. Second,
update the helper to clear the flag unconditionally and release the
batch so long as it is populated. This more clearly delineates the
purpose of the flag to control the I/O path and not necessarily the
status of the fbatch, so add a comment around this as well. |
| In the Linux kernel, the following vulnerability has been resolved:
i3c: dw: avoid shift-out-of-bounds when DAA assigns no devices
On an empty bus ENTDAA assigns nothing, so cmd->rx_len (the count
of addresses left unassigned) equals master->maxdevs.
The GENMASK() index master->maxdevs - cmd->rx_len - 1 then becomes -1,
which trips up UBSAN. This happens every time on boot on a Gigabyte/AMD
server:
UBSAN: shift-out-of-bounds in drivers/i3c/master/dw-i3c-master.c:905:12
shift exponent 64 is too large for 64-bit type 'long unsigned int'
CPU: 7 UID: 0 PID: 963 Comm: (udev-worker) Not tainted 7.0.11-200.fc44.x86_64 #1 PREEMPT(lazy)
Hardware name: Giga Computing E163-Z34-AAH1-000/MZ33-DC1-000, BIOS R32_F45 04/01/2026
Call Trace:
<TASK>
dump_stack_lvl+0x5d/0x80
ubsan_epilogue+0x5/0x2b
__ubsan_handle_shift_out_of_bounds.cold+0xd7/0x1ab
dw_i3c_master_daa.cold+0x1b/0x96 [dw_i3c_master]
i3c_master_do_daa_ext.part.0+0x3e/0xf0 [i3c]
Skip the mask when no new device was assigned. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/dma: Check atomic pool allocation result directly
The non-blocking, non-coherent allocation path uses dma_alloc_from_pool(),
which returns the allocated page and fills cpu_addr only on success.
Do not rely on cpu_addr to detect allocation failure in this path. Check
the returned page directly before using it for the IOMMU mapping. |
| In the Linux kernel, the following vulnerability has been resolved:
md: scope memalloc_noio to allocation critical sections
Storing a memalloc_noio_save() token in mddev->noio_flags lets one task
save the token and another task restore it. With concurrent suspend sysfs
writes, task A can enter PF_MEMALLOC_NOIO, return to userspace still in
that scope, and later task B can restore A's saved token.
Avoid tying the token lifetime to mddev. Keep mddev_suspend() and
mddev_resume() only responsible for array suspension, and enter
PF_MEMALLOC_NOIO only in the MD paths that allocate memory after the array
has been suspended. Restore the token before resuming the array.
A reproducer repeatedly writes suspend_lo and suspend_hi from concurrent
workers and checks each worker's /proc/self/stat flags before and after the
sysfs write. |
| In the Linux kernel, the following vulnerability has been resolved:
md/bitmap: resume array on backlog_store() error path
backlog_store() suspends the array before checking whether a write-mostly
device exists. If no such device exists, the error path only unlocks
reconfig_mutex and leaves the array suspended, blocking subsequent I/O.
Use mddev_unlock_and_resume() to release both states. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: isp1704_charger: cancel work on remove
The USB notifier and initial VBUS detection can schedule isp->work. The
remove path unregisters the notifier and power supply, but does not wait
for queued or running work before tearing down the power supply state.
Cancel the work after unregistering the notifier. Do this before
unregistering the power supply.
This issue was found by a static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
block: fix dio leak on metadata mapping error
A failed integrity mapping holds a dio reference, so we need to go
through the full bio ending in case there were previously submitted
bio's in the sequence. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: qcom: scm: Fix NULL dereference in IRQ handler before __scm is published
In qcom_scm_probe(), devm_request_threaded_irq() is called before
smp_store_release(&__scm, scm). Two paths can dereference __scm before
it is published, both causing a NULL pointer dereference.
The IRQ handler receives scm via its data argument but passes only wq_ctx
to qcom_scm_waitq_wakeup() and qcom_scm_get_completion(), which then
dereference __scm directly. Thread scm through both functions so the IRQ
handler path never touches __scm.
Non-atomic SMC calls made during probe (e.g. from qcom_tzmem_init via
qcom_scm_shm_bridge_enable) can return WAITQ_SLEEP, causing
qcom_scm_wait_for_wq_completion() to run before __scm is published and
dereference it. Add platform_set_drvdata(pdev, scm) early in probe and
change qcom_scm_wait_for_wq_completion() to take the device pointer and
use dev_get_drvdata() to reach scm, removing any dependency on __scm. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix stride mismatch in mac_phy_caps_parse()
Currently, in ath11k_wmi_tlv_mac_phy_caps_parse(), kcalloc() sizes the
mac_phy_caps buffer as tot_phy_id * len, where len is clamped to
min(firmware_len, sizeof(struct wmi_mac_phy_capabilities)). The subsequent
memcpy() destination advances by sizeof(full struct) per slot via C
pointer arithmetic, not by the clamped len. When firmware sends short
TLVs, the second and later slots are written past the end of the
allocation.
The reader in ath11k_pull_mac_phy_cap_svc_ready_ext() also indexes the
buffer with full-struct pointer arithmetic, so the allocation must match
that stride.
Fix by using kzalloc_objs(), which derives the element size from the
pointer type, making allocation size and pointer stride provably
consistent regardless of what len the firmware provides.
Compile tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
media: stm32: dcmi: fix some error handling bugs in probe()
There are a few issues here:
1) After we assign:
chan = dma_request_chan(&pdev->dev, "tx");
Then the error paths need to clean up before returning. The first
error path does a direct return.
2) The error paths check "dcmi->mdma_chan" but that is not assigned
until later so it results in memory leaks. Test "mdma_chan"
instead.
3) The error handling calls dma_release_channel(dcmi->dma_chan) before
"dcmi->dma_chan" has been assigned which leads to a NULL pointer
dereference. Use the "chan" variable instead.
I also moved the call to dma_release_channel() after the call to
dma_release_channel() so it mirrors the allocation code better. |
| In the Linux kernel, the following vulnerability has been resolved:
ARM: 9481/2: breakpoint: CFI breakpoints only on demand
This removes the stub hw_breakpoint_cfi_handler() from ARM, making
it not steal breakpoint type 0x03 (ARM_ENTRY_CFI_BREAKPOINT) unless
CFI is actively used in the kernel.
When not instrumenting with CFI, or when a breakpoint is issued in
userspace, we fall through to return 1 from hw_breakpoint_pending()
"unhandled fault" so userspace can make use of this breakpoint.
Tested with LKDTM and this command line:
echo CFI_FORWARD_PROTO > /sys/kernel/debug/provoke-crash/DIRECT
still works as expected. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/erdma: Hold CQ references when processing EQ events
EQ handlers look up CQs from dev->cq_xa and invoke CQ completion or
error callbacks outside the xarray lock. erdma_destroy_cq() can erase the
CQ from the xarray and free its queue buffer and doorbell record while a
previously scheduled EQ handler is still using the CQ.
Add a CQ refcount and take a reference under the xarray lock with
refcount_inc_not_zero(). Remove the CQ from the xarray before dropping
the destroy-path reference, then wait for in-flight EQ users before
releasing CQ resources. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, cgroup: Fix invalid storage access after __cgroup_bpf_attach failed
A potential invalid storage access issue can occur after replacing a
cgroup bpf prog.
This occurs in the following scenario:
1. prog1 with storage is attached to a cgroup in multi-attach mode.
2. prog1 is replaced with prog2 using BPF_F_REPLACE in multi-attach
mode, but fails midway (e.g. in bpf_trampoline_link_cgroup_shim or
update_effective_progs).
3. A new prog3 is attached to the cgroup in multi-attach mode.
The reason is that __cgroup_bpf_attach overwrites pl->storage with the
new storage prior to attachment completion. When attachment fails
midway, the cleanup path calls bpf_cgroup_storages_free(new_storage) to
free the newly allocated storage, but fails to restore pl->storage back
to old_storage.
Consequently, the still-active prog1 holds invalid or dangling storage
pointers, leading to an invalid memory access when prog1 executes and
calls bpf_get_local_storage. Additionally, original pl->flags and
cgrp->bpf.flags[atype] are left unrestored.
Fix this by saving old_pl_flags, old_storage, and old_flags prior to the
update, and properly restoring all of them in the cleanup path on error. |
| In the Linux kernel, the following vulnerability has been resolved:
remoteproc: fix OOB read via signed offset in rsc_table_for_each_entry()
table->offset[i] is a u32 from firmware, but was stored into a signed
int. A crafted offset like 0xFFFFFFF0 becomes -16, placing hdr 16 bytes
before the table buffer. The subsequent avail check was bypassed
because the negative int was promoted to a large size_t in the
expression "table_sz - offset - sizeof(*hdr)", yielding a large positive
avail and letting the out-of-bounds hdr->type read proceed undetected.
Store the offset as u32 and validate it with unsigned comparisons before
any pointer arithmetic. |
