| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
serial: 8250_of: clear stuck empty-FIFO RX-timeout on LPC32xx
The NXP LPC32xx UART (PORT_LPC3220) can latch an RX character-timeout
interrupt while the RX FIFO is empty: IIR reports UART_IIR_RX_TIMEOUT
(0x0c) but LSR.DR is clear. A character timeout is only cleared by
reading RHR, but serial8250_rx_chars() reads RHR only when LSR.DR is
set, so nothing ever clears the condition. The interrupt is
level-triggered and re-fires immediately, so on a single-core ARM926
the resulting interrupt storm livelocks the CPU.
It is reproducible when userspace repeatedly opens the front-panel port
(ttyS1): serial8250_do_set_termios() re-enables interrupts on unlock and
the handler then spins forever with iir=0xcc lsr=0x60 ier=0x05, tripping
the soft-lockup detector in serial8250_handle_irq_locked().
LPC32xx has no dedicated 8250 glue driver, it's driven by the generic
8250_of. Add a hardware specific handle_irq for PORT_LPC3220, wired up
in of_platform_serial_setup() the same way fsl8250_handle_irq is
installed. The handler follows dw8250_handle_irq(): on an RX timeout
with an empty FIFO (LSR.DR and LSR.BI clear) it does one throwaway RHR
read to clear the condition, then calls serial8250_handle_irq_locked().
No real received data is ever discarded, and it is a no-op on healthy
UARTs which never report a timeout with DR clear.
This is the same class of bug already worked around in other 8250 drivers;
see commit 424d79183af0 ("serial: 8250_dw: Avoid "too much work" from bogus rx timeout interrupt")
which reports the identical iir=0xcc/lsr=0x60. See also
UART_RX_TIMEOUT_QUIRK in 8250_omap, and the note in 8250_bcm7271. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: amba-pl011: cancel RS485 hrtimers after freeing IRQ
The RS485 trigger hrtimers are embedded in the devm-managed port and can
fire after it is freed. The IRQ handler can arm a timer, so free the IRQ
first and then cancel both timers.
Complete the RS485 stop without arming a timer, and cancel the timers
in remove() for the suspend-then-unbind path, where shutdown is not
called.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB read in rtw_get_wpa_ie()
rtw_get_wpa_ie() reads bytes at fixed offsets into a vendor-specific
information element without checking that the element is long enough,
causing an out-of-bounds read for a short trailing IE.
The function locates a vendor-specific IE (EID 221) with rtw_get_ie()
and then compares a 4-byte OUI+type at pbuf + 2 and reads a 2-byte
version word at pbuf + 6. Those accesses require the IE body to be at
least 6 bytes, but rtw_get_ie() only guarantees that the element fits
within the buffer; it does not enforce a minimum body length. A
vendor-specific IE whose length byte is 0 to 5, placed at the end of
the buffer, therefore makes these reads run past the end of the IE and
past the end of the buffer itself.
The buffer holds information elements taken from received management
frames and from the IE blob passed to rtw_cfg80211_set_wpa_ie(), which
is kmemdup'd to its exact length, so the read can run off the end of
the allocation.
The sibling helpers rtw_get_sec_ie(), rtw_get_wapi_ie() and
rtw_get_wps_ie() in this file already reject too-short vendor-specific
IEs before their OUI memcmp(); rtw_get_wpa_ie() was never brought in
line with them, and needs a minimum of 6 rather than 4 bytes because
of the version word. Add the missing length check. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB read in WMM_param_handler()
WMM_param_handler() copies a fixed-size WMM parameter element out of a
received information element without checking that the element is long
enough, causing an out-of-bounds read for a short WMM IE.
The handler reads sizeof(struct WMM_para_element) (18) bytes at
pIE->data + 6, so it requires pIE->length to be at least 24
(WLAN_WMM_LEN), but it never validates the length. Two of its three
callers reach it after matching only the WMM OUI: OnAssocRsp() in
rtw_mlme_ext.c matches a 6-byte OUI, and join_cmd_hdl() matches a
4-byte OUI, before calling the handler. A vendor-specific IE carrying
the WMM OUI but a length between 6 and 23, placed in an association
response or in the IE blob handed to join_cmd_hdl(), passes the OUI
check and then makes the memcmp() and memcpy() at pIE->data + 6 read
past the end of the element. OnAssocRsp() parses a frame received from
the AP, so this is reachable from a remote peer.
The remaining caller in rtw_wlan_util.c already guards the handler with
"pIE->length == WLAN_WMM_LEN". Move the equivalent check into the
handler itself so every caller is covered; the sibling IE handlers in
the same parsing loop (HT_caps_handler(), HT_info_handler(),
ERP_IE_handler()) likewise bound their accesses by pIE->length. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix missing shared-key auth challenge length check
The WEP shared-key authentication handler uses the challenge-text
element's attacker-controlled length without checking it against the
fixed 128-byte chg_txt buffer.
In OnAuthClient() the length from rtw_get_ie() - up to 255 - is used
to perform memcpy() into the 128-byte pmlmeinfo->chg_txt, so a
malicious AP sending a malformed WLAN_EID_CHALLENGE element can
overflow/underfill chg_txt by up to 127 bytes. It is reachable over the
air, before association, during shared-key authentication. In the case
of an overflow, the driver can write out of bounds. In the case of an
underfill, the driver can echo stale buffer memory.
The challenge text is defined to be exactly 128 octets, which is
already provided as the WLAN_AUTH_CHALLENGE_LEN define; require the
element to be exactly that length before use. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: validate monitor transmit frame lengths
rtw_cfg80211_monitor_if_xmit_entry() removes the radiotap header and
then reads the 802.11 frame control field without checking that a base
802.11 header remains.
The data path also pulls the calculated 802.11, QoS and SNAP header
span before confirming that the skb contains it. A truncated frame can
therefore cause out-of-bounds reads or leave insufficient data for the
Ethernet address writes.
Reject frames that do not contain the base 802.11 header and data
frames that do not contain their complete calculated header span. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: fastrpc: Remove buffer from list prior to unmap operation
fastrpc_req_munmap_impl() is called to unmap any buffer. The buffer is
getting removed from the list after it is unmapped from DSP. This can
create potential race conditions if multiple threads invoke unmap
concurrently, where one thread may remove the entry from the list while
another thread's unmap operation is still ongoing.
Fix this by removing the buffer entry from the list before calling the
unmap operation. If the unmap fails, the entry is re-added to the list
so that userspace can retry the unmap, or alternatively, the buffer
will be cleaned up during device release when the DSP process is torn
down and all DSP-side mappings are freed along with remaining buffers
in the list. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: fastrpc: take fl->lock when moving mmaps on interrupted invoke
When an invoke is interrupted by a signal,
wait_for_completion_interruptible() returns -ERESTARTSYS and
fastrpc_internal_invoke() moves every buffer from fl->mmaps onto
cctx->invoke_interrupted_mmaps. This list_del()/list_add_tail() walk
runs without holding fl->lock, the lock that serialises fl->mmaps in
fastrpc_req_mmap() and fastrpc_req_munmap() everywhere else.
Take fl->lock around the move, matching every other fl->mmaps accessor. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/lru_sort: error out for >10000 active_mem_bp
damos_quota_score() can trigger division by zero if the target value is
zero. DAMON_LRU_SORT lets users set the target value for the hot memory
scheme via active_mem_bp parameter. It avoids setting it as the target
value if the parameter value is zero. However, it also sets the cold
memory scheme with a target value that is calculated as '10000 -
active_mem_bp + 2'. Hence, if a user sets active_mem_bp 10002, the cold
memory scheme's quota goal target value can be zero. As a result,
division by zero can be triggered. Fix by returning an error when the
user tries to start DAMON with >10000 active_mem_bp parameter value.
It makes no sense to set active_mem_bp with 10002. It also requires
module parameters write permission to reproduce the issue. That said, the
consequence is quite bad.
One reliable way to reproduce the issue is like below:
# cd /sys/module/damon_lru_sort/parameters
# echo 1000 > wmarks_high
# echo 995 > wmarks_mid
# echo 0 > wmarks_low
# echo 10002 > active_mem_bp
# echo Y > enabled
# dmesg -w
[...]
[ 597.421247] Oops: divide error: 0000 [#1] SMP NOPTI
[ 597.428848] RIP: 0010:damos_quota_score+0x6f/0x480
This issue was discovered [1] by Sashiko. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/ops-common: putback folios on invalid migrate nid
damon_pa_migrate() and damos_va_migrate() isolate folios into a local list
and then call damon_migrate_pages(). When target_nid is invalid
(including the scheme default NUMA_NO_NODE / -1), damon_migrate_pages()
returns early without putting the folios back to the LRU.
Callers then discard the list head while those folios remain isolated with
an extra reference taken by folio_isolate_lru(). The pages stay off the
LRU for as long as the mapping exists (anon active+inactive counts drop
while RSS does not), and the leftover references can pin the pages after
the mapping is gone.
Put the folios back on the invalid-nid path so ignored migration requests
still return them to the LRU. |
| In the Linux kernel, the following vulnerability has been resolved:
samples/damon/mtier: error out for zero quota goal target values
Patch series "mm/damon: avoid division by zero from damos_quota_score()".
DAMON_SAMPLE_MTIER and DAMON_LRU_SORT allow the user to trigger division
by zero in damos_quota_score(). Avoid it by adding parameters validation
checks.
This patch (of 2):
damos_quota_score() can trigger division by zero if the target_value is
zero. DAMON_SAMPLE_MTIER lets users set the target_value via
node0_mem_{used,free}_bp parameters. It doesn't guard zero value case,
though. As a result, users can trigger division by zero. Fix the issue
by returning an error when the user tries to start DAMON with zero
node0_mem_{used,free}_bp parameter values.
DAMON_SAMPLE_MTIER is just a sample module, but the consequence is quite
bad. Also the zero node0_mem_free_bp parameter might look like a
reasonable setup to some users. Hence, the issue might really happen in
the real world.
One reliable way to reproduce the issue is like below:
# cd /sys/module/damon_sample_mtier/parameters
# echo 4096 > node0_start_addr
# echo 8192 > node0_end_addr
# echo 8192 > node1_start_addr
# echo 81920 > node1_end_addr
# echo 0 > node0_mem_free_bp
# echo Y > enabled
# dmesg -w
[...]
[18792.235916] Oops: divide error: 0000 [#1] SMP NOPTI
[...]
[18792.242787] RIP: 0010:damos_quota_score+0x6f/0x480
[...]
This issue was discovered [1] by Sashiko. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb: Fix UAF at delayed release of MIDI2 EPs
The recent fix for UAF in ump_to_endpoint() caused another UAF because
it tries to dereference the UMP endpoint object, but this might be
executed at a delayed context where the endpoint has been already
released.
Add private_free to clear the associated data for avoiding the further
dereference for delayed releases. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usx2y: bound the hwdep mmap fault offset
snd_us428ctls_vm_fault() turns the faulting page offset into a kernel
address with no bound of any kind:
offset = vmf->pgoff << PAGE_SHIFT;
vaddr = (char *)(...)->us428ctls_sharedmem + offset;
page = virt_to_page(vaddr);
get_page(page);
vmf->page = page;
return 0;
snd_us428ctls_mmap() checks only the length of the mapping, never the
offset, and us428ctls_sharedmem is a single page from
alloc_pages_exact(). For a character device file_mmap_size_max()
returns ULONG_MAX, so the mm layer imposes no ceiling either. Every page
offset above zero resolves to a struct page outside the object, and the
handler installs it into the caller's address space read-write; the vma
is not marked read-only.
The caller picks the page frame with a single mmap() argument and gets
read-write access to a page of kernel memory it does not own; an offset
that lands in an unpopulated vmemmap region oopses instead.
A process that can open the hwdep node of an attached US-X2Y reaches
this after loading the FPGA image through the same node; no capability
check is involved.
On 7.2.0-rc5 (arm64), mmap() with a large offset:
Unable to handle kernel paging request at virtual address fffffdffc45d5ac8
pc : snd_us428ctls_vm_fault+0x68/0x140 [snd_usb_usx2y]
Call trace:
snd_us428ctls_vm_fault+0x68/0x140 [snd_usb_usx2y]
__do_fault
__handle_mm_fault
handle_mm_fault
el0_da
Reject any offset outside the shared region. The pcm hwdep handler in
usx2yhwdeppcm.c computes its address the same way and needs the same
bound.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: FCP: fix OOB write in fcp_meter_ctl_get()
fcp_ioctl_set_meter_map() bounds the user-supplied Level Meter map size
by the driver's own limit of 255
if (map.map_size < 1 || map.map_size > 255 ||
map.meter_slots < 1 || map.meter_slots > 255)
return -EINVAL;
and passes it to fcp_add_new_ctl() as the control's channel count, where
it is stored as elem->channels.
Every control read writes into struct snd_ctl_elem_value, whose integer
array is declared long value[128], so the limit is 128, not 255.
fcp_meter_ctl_get() stores one 64-bit word per channel into that array
with no bound of its own:
for (i = 0; i < elem->channels; i++) {
int idx = private->meter_level_map[i];
int value = idx < 0 ? 0 : le32_to_cpu(resp[idx]);
ucontrol->value.integer.value[i] = value;
}
snd_ctl_elem_read_user() serves that object from
memdup_user(_control, sizeof(*control)), 1224 bytes on LP64 out of
kmalloc-2048. offsetof(struct snd_ctl_elem_value, value) is 72, so
element i is written at byte 72 + 8 * i and element 144 already lands
past the allocation. At map_size 255 the last store ends at byte 2112,
888 bytes past the object and 64 bytes into the adjacent slab object.
The stored words come from the device and meter_level_map[] selects
which word lands in which slot, so extent and contents are both
controlled.
The core does not catch this. snd_ctl_check_elem_info() is reached only
from __snd_ctl_elem_info(), which snd_ctl_elem_read() calls under
CONFIG_SND_CTL_DEBUG; without that option snd_ctl_skip_validation() is a
compile-time true. __snd_ctl_add_replace() validates kcontrol->count and
never inspects elem->channels.
Installing an oversized map needs CAP_SYS_RAWIO, but the control outlives
the hwdep descriptor that created it, so the out-of-bounds stores are
issued by any process able to read controls on /dev/snd/controlC0.
KASAN on 7.2.0-rc5 (arm64), triggered by an unprivileged control read:
BUG: KASAN: slab-out-of-bounds in fcp_meter_ctl_get
Write of size 8 at addr ffff000017af04c8 by task fcp_trigger/185
__asan_store8
fcp_meter_ctl_get
snd_ctl_elem_read
snd_ctl_ioctl
Allocated by task 185:
memdup_user
snd_ctl_ioctl
The buggy address is located 0 bytes to the right of
allocated 1224-byte region [ffff000017af0000, ffff000017af04c8)
Bound the map size by the ABI limit rather than by 255, and bound the
store loop at the sink so it cannot run past the value array whatever
elem->channels holds.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: us144mkii: re-anchor capture URBs on resubmission
capture_urb_complete() resubmits each capture URB without anchoring it:
usb_get_urb(urb);
ret = usb_submit_urb(urb, GFP_ATOMIC);
Anchoring is a property of a submission, not of the URB. The giveback
path calls usb_unanchor_urb() before urb->complete(), so an URB
resubmitted from its own completion handler is off the anchor. The
capture URBs are anchored once, at stream start, so from the first
completion onward tascam->capture_anchor is empty.
tascam_free_urbs(), tascam_disconnect(), tascam_suspend() and the
stop-work path all call usb_kill_anchored_urbs(&tascam->capture_anchor)
to reap the capture URBs before anything is freed. With the anchor empty
those calls return immediately and the URBs stay queued on the host
controller.
tascam_free_urbs() then returns the capture transfer buffers with
usb_free_coherent(), and snd_card_free() releases the snd_card
allocation that embeds tascam (card->private_data). The controller
completes the queued URBs afterwards, writing device-supplied data into
the freed transfer buffer, and capture_urb_complete() dereferences the
freed driver object.
KASAN on 7.2.0-rc5 (arm64):
BUG: KASAN: slab-use-after-free in dummy_timer
Write of size 512 at addr ffff000015b62000
__asan_memcpy
dummy_timer
hrtimer_run_softirq
Allocated by task 64:
usb_alloc_coherent
tascam_alloc_urbs
tascam_probe
Freed by task 170:
usb_free_coherent
tascam_free_urbs
tascam_disconnect
usb_unbind_interface
BUG: KASAN: slab-use-after-free in capture_urb_complete
Read of size 4 at addr ffff0000170ee878
Freed by task 170:
release_card_device
snd_card_free
tascam_disconnect
Restore the usb_anchor_urb() between the reference count bump and the
resubmission. That also makes the handler's usb_unanchor_urb() failure
arm meaningful again and restores usb_kill_anchored_urbs() as a barrier
on the disconnect, suspend and stop-work paths.
The anchoring was removed on the premise that the URB is already anchored
from the initial submission, which does not hold once the first giveback
has run.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> |
| In the Linux kernel, the following vulnerability has been resolved:
drm/v3d: Serialize the scheduler timeout handlers
V3D exposes several independent hardware queues (BIN, RENDER, TFU and
CSD) but has only a single, global reset. A timeout on any one queue
therefore has to stop, reset and restart the schedulers of every other
queue as well. That makes concurrent timeout handlers unsafe.
`reset_lock` was never able to make them safe, as a driver-side lock can
only cover the driver's &drm_sched_backend_ops.timedout_job callback.
The scheduler handles the timed out job and its pending list around that
callback, outside of the driver's control, so a global reset triggered
by one queue can still interfere with another queue that is in the
middle of handling a timeout of its own.
Consequently, if a reset happens in the CSD queue while a CL-intensive
application is running, the global reset stops and restarts the CL
queue's scheduler while that queue is handling a timeout of its own. As
drm_sched_stop() and drm_sched_start() subtract and add the credits of
every job sitting on the pending list of the scheduler they are called
on, and as the CL queue's handler concurrently takes its job off that
same list and puts it back, the stop and the start no longer see the
same set of jobs. The CL queue is left with more credits in flight than
its limit:
[ 327.302739] ------------[ cut here ]------------
[ 327.302744] WARNING: CPU: 2 PID: 43 at drivers/gpu/drm/scheduler/sched_main.c:102 drm_sched_run_job_work+0x238/0x4d0 [gpu_sched]
[ 327.302884] CPU: 2 UID: 0 PID: 43 Comm: kworker/u16:1 Not tainted 6.18.39-v8-16k+ #3 PREEMPT
[ 327.302889] Hardware name: Raspberry Pi 5 Model B Rev 1.0 (DT)
[ 327.302893] Workqueue: v3d_bin drm_sched_run_job_work [gpu_sched]
[ 327.302984] Call trace:
[ 327.302987] drm_sched_run_job_work+0x238/0x4d0 [gpu_sched] (P)
[ 327.302997] process_scheduled_works+0x180/0x3d0
[ 327.303010] worker_thread+0x268/0x3e8
[ 327.303016] kthread+0x140/0x250
[ 327.303022] ret_from_fork+0x10/0x20
[ 327.303031] ---[ end trace 0000000000000000 ]---
From that point on, the credit count of the CL queue is broken, causing
a complete GPU hang and UI freeze.
The DRM scheduler already provides a mechanism to serialize the timeout
handlers of different schedulers: an ordered workqueue passed as
drm_sched_init()'s @timeout_wq parameter. By default, each scheduler
queues its timeout work on the system workqueue, which runs the handlers
concurrently. Give all of the queues a shared ordered workqueue instead,
as recommended by the DRM scheduler documentation for hardware that has
distinct queues but resets globally. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/core: Fix group leader use-after-free after sibling detach
perf_group_detach() handles leader and sibling detach differently. When the
group leader is detached, all siblings are promoted to singleton events and
their group_leader pointer is reset to themselves. When a sibling is
detached, it is removed from the leader's sibling_list, but its
group_leader pointer is left pointing at the old leader.
That is harmless when the sibling is being closed and freed immediately, as
in the DETACH_DEAD path. It is not safe when the sibling is detached but
kept alive, such as during CPU hotplug with DETACH_GROUP. In that case the
sibling is removed from the context, while its file descriptor can still
keep it alive.
A typical failing sequence is:
- A group contains leader L and sibling S.
- CPU hot-unplug detaches S with DETACH_GROUP, removing it from
L->sibling_list but leaving S->group_leader == L.
- L is later closed and freed.
- A PERF_IOC_FLAG_GROUP ioctl on S follows S->group_leader and
dereferences the freed leader.
This was reproduced by running the perf event fuzzer, CPU hotplug, and a
stress workload concurrently:
Unable to handle kernel paging request at virtual address 006b6b6b6b6b6cdb
CPU: 2 PID: 12489 Comm: perf_fuzzer 6.18.7 PREEMPT
pc : perf_ioctl+0x34c/0xc68
x20: ffffff89a3fa2c70 x8 : 6b6b6b6b6b6b6b6b
Code: 943c4a0e 340047a0 f9404a94 f9411e88 (f940b908)
Call trace:
perf_ioctl+0x34c/0xc68 (P)
__arm64_sys_ioctl+0xa0/0xf4
invoke_syscall+0x58/0xe4
el0_svc_common+0xa8/0xdc
do_el0_svc+0x1c/0x28
el0_svc+0x40/0xc0
el0t_64_sync_handler+0x68/0xdc
el0t_64_sync+0x1c4/0x1c8
The fault happened in perf_ioctl(), where perf_event_for_each() follows
the stale group_leader pointer and perf_event_for_each_child() then
dereferences the freed leader's context.
Fix the use-after-free by promoting the detached sibling to a singleton.
Also fix __event_disable() cgroup accounting and event state change. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix race between update_event_fields and, event_define_fields
The following sequence may leads race between event_define_fields()
and update_event_fields():
CPU0 (loads module A) CPU1 (loads module B)
=============================== ===============================
load_module(A) load_module(B)
notifier_call_chain notifier_call_chain
trace_module_notify trace_module_notify
mutex_lock(&event_mutex) trace_event_update_all()
trace_module_add_events(A) down_write(&trace_event_sem)
__register_event(call_A)
__add_event_to_tracers(call_A)
event_define_fields(call_A)
for each f: list_for_each_entry(field,
list_add(&f->link, &class->fields, link)
&class->fields) field = class->fields->next;
Where access to the class->fields is not protected by the event_mutex in
trace_event_update_all().
This produces the following panic:
Unable to handle kernel access ... at virtual address 0000000000000018
pc : update_event_fields+0xf8/0x368
Call trace:
update_event_fields+0xf8/0x368
trace_event_update_all+0x7c/0x2b4
trace_module_notify+0x4c/0x1dc
notifier_call_chain+0x84/0x168
blocking_notifier_call_chain_robust+0x64/0xd4
load_module+0x10c8/0x123c
__arm64_sys_finit_module+0x230/0x31c
Fix by taking event_mutex in trace_event_update_all() before
trace_event_sem. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: bitblit: bound-check glyph index in bit_cursor()
bit_cursor() fetches the glyph under the cursor with
c = scr_readw(vc_pos);
src = vc_font.data + ((c & charmask) * w * height);
where charmask is 0x1ff when vc_hi_font_mask is set. The screen buffer
value comes directly from scr_readw() and may be larger than the current
font's glyph count.
Syzkaller triggers this via vcs_write(). The Call Trace shows
vcs_write() in vc_screen.c writing an arbitrary 16-bit value with
writev() to /dev/vcsa, which vcs_write_buf() in vc_screen.c stores via
vcs_scr_writew() without checking charcount. The stored value is later
read in bit_cursor() in bitblit.c.
When the font is changed from a font with 512 glyphs to a font with
256 glyphs, the screen buffer can retain characters with the high
bit set from the previous mode, which could also produce the same
out-of-bounds access.
BUG: KASAN: global-out-of-bounds in soft_cursor+0x378/0x6bc drivers/video/fbdev/core/softcursor.c:70
Read of size 16 at addr ffff800086c57970
Call Trace:
soft_cursor+0x378/0x6bc drivers/video/fbdev/core/softcursor.c:70
bit_cursor+0xa90/0x1108 drivers/video/fbdev/core/bitblit.c:365
fbcon_cursor+0x344/0x498 drivers/video/fbdev/core/fbcon.c:1427
hide_cursor+0xdc/0x2d0 drivers/tty/vt/vt.c:883
update_region+0x100/0x18c drivers/tty/vt/vt.c:669
vcs_write+0x8ec/0xaf0 drivers/tty/vt/vc_screen.c:685
bit_putcs_aligned() and bit_putcs_unaligned() already clamp the glyph
index to vc_font.charcount. Apply the same clamp in bit_cursor() after
extracting the attribute and masking, before indexing fontdata.
The fix completes the bounds checking started in commit 18c4ef4e765a
("fbdev: bitblit: bound-check glyph index in bit_putcs*"), which missed
the cursor path.
This change should be safe because the clamp reuses the existing
contract from fbcon: charcount is maintained under console_lock in
con_font_set() and fbcon_font_set(), and hi_font_mask is cleared when
switching from 512 to 256 glyphs. When stale screen data with high bits
remains after a font switch, or when vcs_write() stores an arbitrary
value, clamping the index to 0 prevents the out-of-bounds read without
changing cursor semantics — the same fallback bit_putcs uses. |
| In the Linux kernel, the following vulnerability has been resolved:
ring-buffer: Prevent subbuf order change when resizing is disabled
Because ring_buffer_subbuf_order_set() frees buffer pages, we can't
allow it when resizing is disabled. A non-consuming reader is at risk of
use-after-free (rb_advance_iter()).
Return -EBUSY on resize_disabled, matching ring_buffer_resize()
behaviour. |
