| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: Fix memory leak after mt76_connac_mcu_alloc_sta_req()
mt76_connac_mcu_alloc_sta_req() allocates an skb which is expected to
be freed eventually by mt76_mcu_skb_send_msg(). However, currently if
an intermediate function fails before sending, the allocated skb is
leaked.
Specifically, mt76_connac_mcu_sta_wed_update() and
mt76_connac_mcu_sta_key_tlv() may fail, leading to an immediate memory
leak in the error path.
Fix this by explicitly freeing the skb in these error paths.
Commit 7c0f63fe37a5 ("wifi: mt76: mt7996: fix memory leak on
mt7996_mcu_sta_key_tlv error") made a similar change.
Compile tested only. Issue found using a prototype static analysis tool
and code review. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921: fix potential deadlock in mt7921_roc_abort_sync
roc_abort_sync() can deadlock with roc_work(). roc_work() holds
dev->mt76.mutex, while cancel_work_sync() waits for roc_work()
to finish. If the caller already owns the same mutex, both
sides block and no progress is possible.
This deadlock can occur during station removal when
mt76_sta_state() -> mt76_sta_remove() -> mt7921_mac_sta_remove() ->
mt7921_roc_abort_sync() invokes cancel_work_sync() while
roc_work() is still running and holding dev->mt76.mutex.
This avoids the mutex deadlock and preserves exactly-once
work ownership. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: fix deadlock in remain-on-channel
mt76_remain_on_channel() and mt76_roc_complete() call mt76_set_channel()
while already holding dev->mutex. Since mt76_set_channel() also acquires
dev->mutex, this results in a deadlock.
Use __mt76_set_channel() instead of mt76_set_channel().
Add cancel_delayed_work_sync() for mac_work before acquiring the mutex
in mt76_remain_on_channel() to prevent a secondary deadlock with the
mac_work workqueue. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Switch CONFIG_CFI_CLANG to CONFIG_CFI
This was renamed in commit 23ef9d439769 ("kcfi: Rename CONFIG_CFI_CLANG
to CONFIG_CFI") as it is now a compiler-agnostic option. Using the wrong
name results in the code getting compiled out. Meaning the CFI failures
for btf_dtor_kfunc_t would still trigger. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: fix use-after-free bugs in mt7915_mac_dump_work()
When the mt7915 pci chip is detaching, the mt7915_crash_data is
released in mt7915_coredump_unregister(). However, the work item
dump_work may still be running or pending, leading to UAF bugs
when the already freed crash_data is dereferenced again in
mt7915_mac_dump_work().
The race condition can occur as follows:
CPU 0 (removal path) | CPU 1 (workqueue)
mt7915_pci_remove() | mt7915_sys_recovery_set()
mt7915_unregister_device() | mt7915_reset()
mt7915_coredump_unregister() | queue_work()
vfree(dev->coredump.crash_data) | mt7915_mac_dump_work()
| crash_data-> // UAF
Fix this by ensuring dump_work is properly canceled before
the crash_data is deallocated. Add cancel_work_sync() in
mt7915_unregister_device() to synchronize with any pending
or executing dump work. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: fix use-after-free bugs in mt7996_mac_dump_work()
When the mt7996 pci chip is detaching, the mt7996_crash_data is
released in mt7996_coredump_unregister(). However, the work item
dump_work may still be running or pending, leading to UAF bugs
when the already freed crash_data is dereferenced again in
mt7996_mac_dump_work().
The race condition can occur as follows:
CPU 0 (removal path) | CPU 1 (workqueue)
mt7996_pci_remove() | mt7996_sys_recovery_set()
mt7996_unregister_device() | mt7996_reset()
mt7996_coredump_unregister() | queue_work()
vfree(dev->coredump.crash_data) | mt7996_mac_dump_work()
| crash_data-> // UAF
Fix this by ensuring dump_work is properly canceled before
the crash_data is deallocated. Add cancel_work_sync() in
mt7996_unregister_device() to synchronize with any pending
or executing dump work. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Use RCU-safe iteration in dev_map_redirect_multi() SKB path
The DEVMAP_HASH branch in dev_map_redirect_multi() uses
hlist_for_each_entry_safe() to iterate hash buckets, but this function
runs under RCU protection (called from xdp_do_generic_redirect_map()
in softirq context). Concurrent writers (__dev_map_hash_update_elem,
dev_map_hash_delete_elem) modify the list using RCU primitives
(hlist_add_head_rcu, hlist_del_rcu).
hlist_for_each_entry_safe() performs plain pointer dereferences without
rcu_dereference(), missing the acquire barrier needed to pair with
writers' rcu_assign_pointer(). On weakly-ordered architectures (ARM64,
POWER), a reader can observe a partially-constructed node. It also
defeats CONFIG_PROVE_RCU lockdep validation and KCSAN data-race
detection.
Replace with hlist_for_each_entry_rcu() using rcu_read_lock_bh_held()
as the lockdep condition, consistent with the rcu_dereference_check()
used in the DEVMAP (non-hash) branch of the same functions. Also fix
the same incorrect lockdep_is_held(&dtab->index_lock) condition in
dev_map_enqueue_multi(), where the lock is not held either. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix abuse of kprobe_write_ctx via freplace
uprobe programs are allowed to modify struct pt_regs.
Since the actual program type of uprobe is KPROBE, it can be abused to
modify struct pt_regs via kprobe+freplace when the kprobe attaches to
kernel functions.
For example,
SEC("?kprobe")
int kprobe(struct pt_regs *regs)
{
return 0;
}
SEC("?freplace")
int freplace_kprobe(struct pt_regs *regs)
{
regs->di = 0;
return 0;
}
freplace_kprobe prog will attach to kprobe prog.
kprobe prog will attach to a kernel function.
Without this patch, when the kernel function runs, its first arg will
always be set as 0 via the freplace_kprobe prog.
To fix the abuse of kprobe_write_ctx=true via kprobe+freplace, disallow
attaching freplace programs on kprobe programs with different
kprobe_write_ctx values. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix stale offload->prog pointer after constant blinding
When a dev-bound-only BPF program (BPF_F_XDP_DEV_BOUND_ONLY) undergoes
JIT compilation with constant blinding enabled (bpf_jit_harden >= 2),
bpf_jit_blind_constants() clones the program. The original prog is then
freed in bpf_jit_prog_release_other(), which updates aux->prog to point
to the surviving clone, but fails to update offload->prog.
This leaves offload->prog pointing to the freed original program. When
the network namespace is subsequently destroyed, cleanup_net() triggers
bpf_dev_bound_netdev_unregister(), which iterates ondev->progs and calls
__bpf_prog_offload_destroy(offload->prog). Accessing the freed prog
causes a page fault:
BUG: unable to handle page fault for address: ffffc900085f1038
Workqueue: netns cleanup_net
RIP: 0010:__bpf_prog_offload_destroy+0xc/0x80
Call Trace:
__bpf_offload_dev_netdev_unregister+0x257/0x350
bpf_dev_bound_netdev_unregister+0x4a/0x90
unregister_netdevice_many_notify+0x2a2/0x660
...
cleanup_net+0x21a/0x320
The test sequence that triggers this reliably is:
1. Set net.core.bpf_jit_harden=2 (echo 2 > /proc/sys/net/core/bpf_jit_harden)
2. Run xdp_metadata selftest, which creates a dev-bound-only XDP
program on a veth inside a netns (./test_progs -t xdp_metadata)
3. cleanup_net -> page fault in __bpf_prog_offload_destroy
Dev-bound-only programs are unique in that they have an offload structure
but go through the normal JIT path instead of bpf_prog_offload_compile().
This means they are subject to constant blinding's prog clone-and-replace,
while also having offload->prog that must stay in sync.
Fix this by updating offload->prog in bpf_jit_prog_release_other(),
alongside the existing aux->prog update. Both are back-pointers to
the prog that must be kept in sync when the prog is replaced. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: Fix error pointer dereference
The function brcmf_chip_add_core() can return an error pointer and is
not checked. Add checks for error pointer.
Detected by Smatch:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:1010 brcmf_chip_recognition() error:
'core' dereferencing possible ERR_PTR()
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:1013 brcmf_chip_recognition() error:
'core' dereferencing possible ERR_PTR()
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:1016 brcmf_chip_recognition() error:
'core' dereferencing possible ERR_PTR()
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:1019 brcmf_chip_recognition() error:
'core' dereferencing possible ERR_PTR()
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:1022 brcmf_chip_recognition() error:
'core' dereferencing possible ERR_PTR()
[add missing wifi: prefix] |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix linked reg delta tracking when src_reg == dst_reg
Consider the case of rX += rX where src_reg and dst_reg are pointers to
the same bpf_reg_state in adjust_reg_min_max_vals(). The latter first
modifies the dst_reg in-place, and later in the delta tracking, the
subsequent is_reg_const(src_reg)/reg_const_value(src_reg) reads the
post-{add,sub} value instead of the original source.
This is problematic since it sets an incorrect delta, which sync_linked_regs()
then propagates to linked registers, thus creating a verifier-vs-runtime
mismatch. Fix it by just skipping this corner case. |
| In the Linux kernel, the following vulnerability has been resolved:
net: pull headers in qdisc_pkt_len_segs_init()
Most ndo_start_xmit() methods expects headers of gso packets
to be already in skb->head.
net/core/tso.c users are particularly at risk, because tso_build_hdr()
does a memcpy(hdr, skb->data, hdr_len);
qdisc_pkt_len_segs_init() already does a dissection of gso packets.
Use pskb_may_pull() instead of skb_header_pointer() to make
sure drivers do not have to reimplement this.
Some malicious packets could be fed, detect them so that we can
drop them sooner with a new SKB_DROP_REASON_SKB_BAD_GSO drop_reason. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix ld_{abs,ind} failure path analysis in subprogs
Usage of ld_{abs,ind} instructions got extended into subprogs some time
ago via commit 09b28d76eac4 ("bpf: Add abnormal return checks."). These
are only allowed in subprograms when the latter are BTF annotated and
have scalar return types.
The code generator in bpf_gen_ld_abs() has an abnormal exit path (r0=0 +
exit) from legacy cBPF times. While the enforcement is on scalar return
types, the verifier must also simulate the path of abnormal exit if the
packet data load via ld_{abs,ind} failed.
This is currently not the case. Fix it by having the verifier simulate
both success and failure paths, and extend it in similar ways as we do
for tail calls. The success path (r0=unknown, continue to next insn) is
pushed onto stack for later validation and the r0=0 and return to the
caller is done on the fall-through side. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix use-after-free in offloaded map/prog info fill
When querying info for an offloaded BPF map or program,
bpf_map_offload_info_fill_ns() and bpf_prog_offload_info_fill_ns()
obtain the network namespace with get_net(dev_net(offmap->netdev)).
However, the associated netdev's netns may be racing with teardown
during netns destruction. If the netns refcount has already reached 0,
get_net() performs a refcount_t increment on 0, triggering:
refcount_t: addition on 0; use-after-free.
Although rtnl_lock and bpf_devs_lock ensure the netdev pointer remains
valid, they cannot prevent the netns refcount from reaching zero.
Fix this by using maybe_get_net() instead of get_net(). maybe_get_net()
uses refcount_inc_not_zero() and returns NULL if the refcount is already
zero, which causes ns_get_path_cb() to fail and the caller to return
-ENOENT -- the correct behavior when the netns is being destroyed. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bcmgenet: fix off-by-one in bcmgenet_put_txcb
The write_ptr points to the next open tx_cb. We want to return the
tx_cb that gets rewinded, so we must rewind the pointer first then
return the tx_cb that it points to. That way the txcb can be correctly
cleaned up. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bcmgenet: fix leaking free_bds
While reclaiming the tx queue we fast forward the write pointer to
drop any data in flight. These dropped frames are not added back
to the pool of free bds. We also need to tell the netdev that we
are dropping said data. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bcmgenet: fix racing timeout handler
The bcmgenet_timeout handler tries to take down all tx queues when
a single queue times out. This is over zealous and causes many race
conditions with queues that are still chugging along. Instead lets
only restart the timed out queue. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: fix mm lifecycle in open-coded task_vma iterator
The open-coded task_vma iterator reads task->mm locklessly and acquires
mmap_read_trylock() but never calls mmget(). If the task exits
concurrently, the mm_struct can be freed as it is not
SLAB_TYPESAFE_BY_RCU, resulting in a use-after-free.
Safely read task->mm with a trylock on alloc_lock and acquire an mm
reference. Drop the reference via bpf_iter_mmput_async() in _destroy()
and error paths. bpf_iter_mmput_async() is a local wrapper around
mmput_async() with a fallback to mmput() on !CONFIG_MMU.
Reject irqs-disabled contexts (including NMI) up front. Operations used
by _next() and _destroy() (mmap_read_unlock, bpf_iter_mmput_async)
take spinlocks with IRQs disabled (pool->lock, pi_lock). Running from
NMI or from a tracepoint that fires with those locks held could
deadlock.
A trylock on alloc_lock is used instead of the blocking task_lock()
(get_task_mm) to avoid a deadlock when a softirq BPF program iterates
a task that already holds its alloc_lock on the same CPU. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: return VMA snapshot from task_vma iterator
Holding the per-VMA lock across the BPF program body creates a lock
ordering problem when helpers acquire locks that depend on mmap_lock:
vm_lock -> i_rwsem -> mmap_lock -> vm_lock
Snapshot the VMA under the per-VMA lock in _next() via memcpy(), then
drop the lock before returning. The BPF program accesses only the
snapshot.
The verifier only trusts vm_mm and vm_file pointers (see
BTF_TYPE_SAFE_TRUSTED_OR_NULL in verifier.c). vm_file is reference-
counted with get_file() under the lock and released via fput() on the
next iteration or in _destroy(). vm_mm is already correct because
lock_vma_under_rcu() verifies vma->vm_mm == mm. All other pointers
are left as-is by memcpy() since the verifier treats them as untrusted. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix RCU stall in bpf_fd_array_map_clear()
Add a missing cond_resched() in bpf_fd_array_map_clear() loop.
For PROG_ARRAY maps with many entries this loop calls
prog_array_map_poke_run() per entry which can be expensive, and
without yielding this can cause RCU stalls under load:
rcu: Stack dump where RCU GP kthread last ran:
CPU: 0 UID: 0 PID: 30932 Comm: kworker/0:2 Not tainted 6.14.0-13195-g967e8def1100 #2 PREEMPT(undef)
Workqueue: events prog_array_map_clear_deferred
RIP: 0010:write_comp_data+0x38/0x90 kernel/kcov.c:246
Call Trace:
<TASK>
prog_array_map_poke_run+0x77/0x380 kernel/bpf/arraymap.c:1096
__fd_array_map_delete_elem+0x197/0x310 kernel/bpf/arraymap.c:925
bpf_fd_array_map_clear kernel/bpf/arraymap.c:1000 [inline]
prog_array_map_clear_deferred+0x119/0x1b0 kernel/bpf/arraymap.c:1141
process_one_work+0x898/0x19d0 kernel/workqueue.c:3238
process_scheduled_works kernel/workqueue.c:3319 [inline]
worker_thread+0x770/0x10b0 kernel/workqueue.c:3400
kthread+0x465/0x880 kernel/kthread.c:464
ret_from_fork+0x4d/0x80 arch/x86/kernel/process.c:153
ret_from_fork_asm+0x19/0x30 arch/x86/entry/entry_64.S:245
</TASK> |
