| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: do not leak an hci_conn when a second LE connect is rejected
create_le_conn_complete() decides whether the failed connection is
still pending by comparing it against hci_lookup_le_connect(), which
returns the first LE connection in BT_CONNECT. That is the same
connection only while at most one is pending.
Two can be pending. Connections created on the passive scan path sit
in BT_CONNECT with HCI_CONN_SCANNING set and are invisible to
hci_lookup_le_connect() until hci_le_create_conn_sync() clears the
flag when their command is issued, so the -EBUSY guard in
hci_connect_le() does not prevent a second connection from being
queued while the first is still on the scan path. Whenever two
connections are in BT_CONNECT at once, the lookup may return one
connection while create_le_conn_complete() is reporting the failure
of the other; the early exit then drops the error and hci_conn_failed()
never runs on the connection that failed.
The controller also rejects a second HCI_OP_LE_CREATE_CONN issued
while another connection creation is still outstanding, per Core Spec
Vol 4, Part E. The spec calls for Command Disallowed there; the
bcm43438 observed here answers with an LMP/LL error code instead,
which bt_to_errno() maps to the -EPROTO (-71) in the log below.
The leaked connection stays in BT_CONNECT forever, and because
hci_connect_le() refuses to dial while hci_lookup_le_connect() finds
anything, every subsequent attempt to reach any peer fails with
-EBUSY and no command reaches the controller at all.
Seen on a bcm43438 with two BLE peers polled on the same interval
(state 5 is BT_CONNECT; both handles are UNSET ones, allocated from
the ida above HCI_CONN_HANDLE_MAX):
Bluetooth: hci1: Opcode 0x2013 failed: -71
# hcitool con
< LE 14:9C:EF:03:68:81 handle 3840 state 5 lm CENTRAL
< LE C4:D3:6A:8C:B5:38 handle 3841 state 5 lm CENTRAL
A btmon capture across the next ten minutes of connect attempts
contains no HCI_OP_LE_CREATE_CONN at all; outgoing LE connections
do not recover until the adapter is reset. With this change the same
scenario fails the rejected connection cleanly and further connects
to both peers go through.
Ask about the connection itself instead of about the device. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: fix race l2cap_sock_cleanup_listen() vs. put_chan
For L2CAP sockets without owning sk->sk_socket, reading
l2cap_pi(sk)->chan may race against concurrent l2cap_sock_kill() ->
l2cap_sock_put_chan(). This excludes simultaneous proto_ops callbacks,
but access in l2cap_sock_cleanup_listen() has unsafe lockless read.
[Task 1] [Task 2 (hdev->workqueue)]
l2cap_sock_release(parent) l2cap_disconn_cfm
l2cap_sock_cleanup_listen l2cap_conn_del
bt_accept_dequeue l2cap_chan_del
lock_sock(sk) l2cap_sock_teardown_cb
bt_accept_unlink
bt_sk(sk)->parent = NULL
release_sock(sk) ----------------> lock_sock(sk)
parent = /* NULL */
lock_sock(sk) <--------------------- release_sock(sk)
sock_set_flag(sk, SOCK_ZAPPED)
l2cap_sock_close_cb
l2cap_sock_kill(sk)
l2cap_sock_put_chan
chan = READ l2cap_pi(sk)->chan l2cap_pi(sk)->chan = NULL
l2cap_chan_hold_unless_zero l2cap_put_chan(chan)
kref_get_unless_zero(&chan->ref)
Task 1 may observe NULL which causes null-ptr-deref.
Fix the race by taking lock_sock() in l2cap_sock_kill() to
synchronize with l2cap_sock_cleanup_listen(). hold_unless_zero() is not
needed here, l2cap_pi(sk)->chan owns reference if it is non-NULL.
Clarify code comments vs. locking. |
| Rsyslog is a rocket-fast system for log processing. From 8.2110.0 until 8.2604.0, the optional imhttp module's parse_auth_header function in contrib/imhttp/imhttp.c allocates a zero-byte heap buffer with calloc(0, len) when an HTTP Basic Authorization value exceeds its fixed work buffer, then passes that pointer to apr_base64_decode. An unauthenticated remote attacker can send an oversized encoded credential to an imhttp endpoint configured for Basic Authentication, causing decoded data to overwrite adjacent heap memory before credential validation. Deployments that do not install, load, and use imhttp with Basic Authentication are not affected. The demonstrated impact is a process crash that interrupts log collection, and code execution has not been demonstrated. This issue is fixed in version 8.2604.0. |
| Rsyslog is a rocket-fast system for log processing. From 7.5.4 until 8.2606.0, the optional mmpstrucdata plugin's parseSD_PARAM function in plugins/mmpstrucdata/mmpstrucdata.c stores RFC5424 parameter values in a fixed pVal[32 * 1024] stack buffer and calls parsePARAM_VALUE without supplying the destination size. A remote unauthenticated attacker whose crafted RFC5424 message reaches an action using mmpstrucdata can provide a structured-data parameter larger than that buffer when MaxMessageSize permits it, causing an attacker-controlled stack overwrite. Deployments that do not install and use the plugin, or whose effective message-size limit remains below the required threshold, are not affected by this issue. The demonstrated impact is a crash and interruption of log collection; code execution is not demonstrated. This issue is fixed in version 8.2606.0. |
| zot is a container image and artifact registry based on the Open Container Initiative Distribution Specification. Prior to 2.1.18, the bearer authentication handler in pkg/api/authn.go maps every HTTP method other than GET and HEAD to the push action, so DELETE requests are not checked for the distinct delete permission. Bearer-authenticated requests also bypass the fine-grained DistSpecAuthzHandler path in pkg/api/authz.go, while DeleteManifest and DeleteBlob perform no independent delete-permission check. A remote attacker with a bearer token limited to pull and push actions can therefore delete manifests and blobs within the token's repository scope, making images unavailable and allowing repository history to be altered despite the token lacking delete authorization. This issue is fixed in version 2.1.18. |
| Paymenter is a free and open-source webshop solution for management of hosting services. Prior to 1.5.7, app/Livewire/Services/Upgrade.php::doUpgrade() relies on Service::upgradable to check for a pending service upgrade and later executes $credit->increment('amount', abs($price)) without DB::transaction or lockForUpdate() spanning those operations. An authenticated customer with an active downgradable service can submit concurrent downgrade requests that each observe no pending upgrade, create separate upgrade records, and increment the same account credit balance, producing multiple spendable refunds for one downgrade. This issue is fixed in version 1.5.7. |
| SysReptor is a fully customizable pentest reporting platform. Prior to 2026.58, installations that enable password reset by email while configuring ALLOWED_HOSTS with a wildcard accept an attacker-controlled Host header when generating a password reset link. An unauthenticated attacker can request a reset email whose link points to an attacker-controlled system, and a victim who follows that link can disclose the reset token, allowing the attacker to reset the victim's password and take over the account. Exploitation also requires a configured email gateway and an email address for the victim, while some reverse proxy configurations may reject the hostile Host header. This issue is fixed in version 2026.58. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: validate banner payload length
When parsing the Ceph messenger v2 protocol banner, the `payload_len` field
is decoded from the banner prefix. If a client sends a banner with a
`payload_len` of 0, the kernel sets up a 0-length socket read. This
violates an invariant in the state machine, triggering a warning in
`populate_in_iter()`:
------------[ cut here ]------------
!iov_iter_count(&con->v2.in_iter)
WARNING: net/ceph/messenger_v2.c:3129 at populate_in_iter
net/ceph/messenger_v2.c:3129 [inline], CPU#1: kworker/1:3/5070
WARNING: net/ceph/messenger_v2.c:3129 at ceph_con_v2_try_read+0x6634/0x6810
net/ceph/messenger_v2.c:3159, CPU#1: kworker/1:3/5070
...
Call Trace:
<TASK>
ceph_con_workfn+0x1f5/0x14a0 net/ceph/messenger.c:1575
process_one_work kernel/workqueue.c:3322 [inline]
process_scheduled_works+0xa8e/0x14e0 kernel/workqueue.c:3405
worker_thread+0xa47/0xfb0 kernel/workqueue.c:3486
kthread+0x388/0x470 kernel/kthread.c:436
ret_from_fork+0x514/0xb70 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK>
According to the msgr2 protocol specification, the banner payload is
expected to contain at least two 64-bit integers (`server_feat` and
`server_req_feat`). Therefore, `payload_len` must be at least 16 bytes.
Fix this by adding a check in `process_banner_prefix()` to reject a
`payload_len` smaller than 16 bytes. This prevents the 0-length read and
correctly aborts the connection with a protocol error. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: sfq: clamp quantum to avoid signed overflow soft lockup
sfq_init() sets q->quantum = psched_mtu(qdisc_dev(sch)) (unsigned). A
device with a huge MTU (e.g. dummy with max_mtu == 0 accepting MTU
2147483634) makes psched_mtu() return 0x80000000, so slot->allot = INT_MIN
and INT_MIN + INT_MIN toggles between INT_MIN and 0 forever, spinning
sfq_dequeue() under the qdisc lock.
Clamp the quantum to [256, 1 << 20] so the refill loop terminates. The
lower bound also covers q->quantum == 0 (psched_mtu() returning 0),
which spins sfq_dequeue() identically. sfq_change() already rejects a
negative quantum, so only the init path was exposed.
Conditions to recreate the bug: a device whose MTU (plus
hard_header_len) wraps psched_mtu() into the sign bit (e.g. a dummy
device with max_mtu == 0 accepting MTU 2147483634). Requires
CAP_NET_ADMIN in a user namespace. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: hhf: clamp quantum before hhf_change() to avoid overflow
hhf_init() sets q->quantum = psched_mtu(qdisc_dev(sch)) with no overflow
check. A device with a huge MTU (e.g. dummy with max_mtu == 0 accepting
MTU 2147483634) makes weight * quantum overflow the signed deficit in
hhf_dequeue(), spinning forever.
Clamp q->quantum before hhf_change() so both the opt and !opt paths see
a sane quantum. Without this, bare "tc qdisc add ... hhf" succeeds with
a clamped quantum but "tc qdisc add ... hhf limit 1000" (any option
present) fails with -EINVAL because hhf_change() re-validates the
unclamped default (sch_hhf.c:559). 256 matches fq_codel's floor and is
a sane minimum for a DRR quantum.
Conditions to recreate the bug: a device whose MTU (plus
hard_header_len) wraps psched_mtu() into the sign bit (e.g. a dummy
device with max_mtu == 0 accepting MTU 2147483634). Requires
CAP_NET_ADMIN in a user namespace. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: fq_pie: clamp default quantum to avoid signed overflow
fq_pie_init() sets q->quantum = psched_mtu(qdisc_dev(sch)) without
clamping. A device with a huge MTU (e.g. dummy with max_mtu == 0
accepting MTU 2147483634) makes psched_mtu() return 0x80000000, which
overflows the signed flow->deficit to INT_MIN in fq_pie_qdisc_dequeue(),
causing an infinite loop and soft lockup. Emulate fq_pie_policy which
is already bounded to [1, 1 << 20]; clamp the default to [256, 1 << 20].
256 matches fq_codel's floor and is a sane minimum for a DRR quantum.
Conditions to recreate the bug: a device whose MTU (plus
hard_header_len) wraps psched_mtu() into the sign bit (e.g. a dummy
device with max_mtu == 0 accepting MTU 2147483634). Requires
CAP_NET_ADMIN in a user namespace. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: fq: add overflow bounds to quantum and initial quantum
fq_init() computes quantum = 2 * psched_mtu() and initial_quantum = 10 *
psched_mtu() with no overflow check. A device with a huge MTU (e.g. dummy
with max_mtu == 0 accepting MTU 2147483634) makes psched_mtu() return
0x80000000; the 2 * and 10 * multiplications wrap to 0 in 32-bit
arithmetic, so q->quantum == 0. Then in fq_dequeue() the credit-refill
loop adds 0 to f->credit (which stays <= 0) and goto begin loops
forever under the qdisc lock, creating a soft lockup.
Clamp psched_mtu() to [1, 1 << 20] before multiplying so the product
cannot wrap, then cap the result at 1 << 20, matching the bound already
enforced on TCA_FQ_QUANTUM in fq_change().
Conditions to recreate the bug: a device whose MTU (plus
hard_header_len) is large enough that 2 * psched_mtu() wraps (e.g. a
dummy device with max_mtu == 0 accepting MTU 2147483634). Requires
CAP_NET_ADMIN in a user namespace. |
| In the Linux kernel, the following vulnerability has been resolved:
net: fix a resource leak in copy_net_ns() error handling path
Currently, preinit_net() does two things:
(1) call ns_common_init() which might fail
(2) initialize resources which does not fail
However, preinit_net() is returning early when (1) fails, and copy_net_ns()
is jumping to the dec_ucounts: label. As a result, resources allocated by
net_alloc() are leaking. We need to call key_remove_domain() and
net_passive_dec() in order to release resources allocated by net_alloc().
We cannot simply jump to the put_userns: label when preinit_net() failed,
for (2) is not yet done. But we can reorder (1) and (2), for there is no
dependency between (1) and (2). Therefore, this patch decouples (1) from
preinit_net() and changes preinit_net() back to a void function, and calls
ns_common_init() after preinit_net() succeeded. Then, we can jump to
immediately after ns_common_free() of the put_userns: label. |
| In the Linux kernel, the following vulnerability has been resolved:
octeontx2-af: fix cn20k mailbox lifetime on repeated rvu_mbox_init()
rvu_mbox_init() is called separately for AF-PF mailboxes during probe
and for AF-VF mailboxes when SR-IOV is enabled. Each call used to
allocate a new ng_rvu object, leaking the first allocation when the
pointer was overwritten on the second call.
Sharing one ng_rvu across both paths exposed several teardown bugs:
the error path freed all cn20k mailbox DMA and kfree()d ng_rvu even
when only the failing init type should be unwound, leaving live AF-PF
mailbox memory in use after an AF-VF init failure. mutex_init() was
also re-run on the AF-VF path while AF-PF mailbox handlers could still
hold rvu->mbox_lock. Probe and SR-IOV failure paths did not release
cn20k mailbox DMA either, since cleanup only happened in rvu_remove().
Allocate ng_rvu once with devm_kzalloc(), initialize mbox_lock in the
same block, unwind only the mailbox memory for the failing init type,
and free cn20k mailbox DMA from the probe and pci_enable_sriov()
error paths. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: process: Fix context switching MTE store-only tag check
SCTLR_EL1.TCSO0 is set when user opt-in for MTE store-only tag check
mode. However, it is not part of SCTLR_USER_MASK which imply that on
context switch we never clear SCTLR_EL1.TCSO0, so we are leaking that
setting into another task.
Fix that by including SCTLR_EL1_TCSO0_MASK into SCTLR_USER_MASK |
| In the Linux kernel, the following vulnerability has been resolved:
ptp: netc: fix period truncation and potential divide-by-zero in PEROUT
The max_period bound in net_timer_enable_perout() was computed as:
max_period = (u64)NETC_TMR_DEFAULT_FIPER + integral_period;
which exceeds U32_MAX when integral_period > 0 (e.g. 0x100000002 for
the default 333333333 Hz clock). A period_ns that passes this check but
exceeds U32_MAX is then silently truncated when stored into the u32
struct netc_pp::period field.
A truncated value of zero can reach netc_timer_set_perout_alarm(), where
the local u32 period variable would also be 0, causing a divide-by-zero
in roundup_u64(delta, period) whenever the stime < min_time branch is
taken (which always happens for a start time of {0, 0}).
Additionally, netc_timer_enable_periodic_pulse() and
netc_timer_enable_fiper() both compute:
fiper = pp->period - integral_period;
A zero pp->period results in an unsigned wraparound to 0xFFFFFFFD,
mis-programming the FIPER hardware register.
Fix all three issues by capping max_period at NETC_TMR_DEFAULT_FIPER
(0xFFFFFFFF). This ensures that any period_ns passing the range check
fits in a u32 without truncation, so the stored value is always valid
and non-zero. The accepted range is reduced by integral_period ns
(typically only a few nanoseconds), which is negligible in practice. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSv4/pnfs: key the data server cache on the NFS version
nfs4_pnfs_ds_add() keys the per-net data server cache on the multipath
address set alone, and struct nfs4_pnfs_ds records no version. That
suffices for the files layout driver, which always connects with version
4, but flexfiles takes its version tuple from GETDEVICEINFO per device,
and one address can legitimately serve both NFSv3 and NFSv4.
Two deviceids on one address with different ds_versions[0].version
therefore share a single nfs4_pnfs_ds, and whichever mirror connects
first pins ds_clp to its own version. The other one is handed that
client anyway, so it selects rpc_call_ops for a version the connection
does not speak, and the mismatched sequence-slot handling dereferences
NULL.
Add the version to the cache key so the two cannot alias, giving each
version its own nfs4_pnfs_ds and connection while both mirrors stay
usable. Only the major version is compared, since that is what selects
rpc_call_ops and rpc_ops; v4.0 and v4.1 keep sharing a client. The files
layout driver passes the 4 it already hardcodes at connect time. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: free stashed qentry before overwrite in REQ_ADD_LINK to ADD_LINK transition
When smc_llc_event_handler() transitions the local LLC flow from
SMC_LLC_FLOW_REQ_ADD_LINK to SMC_LLC_FLOW_ADD_LINK on arrival of an ADD_LINK
request, it calls smc_llc_flow_qentry_set() unconditionally:
if (lgr->llc_flow_lcl.type == SMC_LLC_FLOW_REQ_ADD_LINK) {
lgr->llc_flow_lcl.type = SMC_LLC_FLOW_ADD_LINK;
smc_llc_flow_qentry_set(&lgr->llc_flow_lcl, qentry);
...
}
A CONFIRM_LINK or ADD_LINK_CONT arriving while flow->type is
SMC_LLC_FLOW_REQ_ADD_LINK is stashed into flow->qentry via the
SMC_LLC_CONFIRM_LINK / SMC_LLC_ADD_LINK_CONT handler (which stores into
flow->qentry for any non-NONE flow type). When the subsequent ADD_LINK
arrives, the REQ_ADD_LINK branch overwrites flow->qentry with the new pointer
without first freeing the stashed allocation, leaking one kmalloc object.
The stashed entry has no consumer: smc_llc_wait() is only called from
llc_add_link_work, which is not yet scheduled while the flow type remains
REQ_ADD_LINK. No waiter is sleeping on llc_msg_waiter at this point.
It is safe to unconditionally free any stashed qentry before
the overwrite.
Call smc_llc_flow_qentry_del() before smc_llc_flow_qentry_set() in the
REQ_ADD_LINK branch. smc_llc_flow_qentry_del() already checks flow->qentry
before freeing, so the normal path where no entry is stashed is a no-op. |
| In the Linux kernel, the following vulnerability has been resolved:
vdpa/mlx5: fix wrong list iterated in add_direct_chain error path
In add_direct_chain(), newly allocated direct MR entries are added to
the local list 'tmp', which is spliced into mr->head only on success.
On the error path, the cleanup loop was incorrectly iterating over
mr->head instead of tmp.
Fix by iterating over 'tmp' in the err_alloc cleanup path. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: check for NULL root inode in fuse_fill_super_submount
fuse_iget() can return NULL when its inode allocation fails, but
fuse_fill_super_submount() passed the result straight to get_fuse_inode()
and decremented fi->nlookup without checking it:
root = fuse_iget(sb, parent_fi->nodeid, ...);
fi = get_fuse_inode(root);
fi->nlookup--;
Inside fuse_iget() the inode allocation can fail and return NULL. The
submount root takes the iget5_locked() path, whose alloc_inode() can fail
under memory pressure (the auto-submount branch can fail the same way in
new_inode() or fuse_alloc_submount_lookup()):
inode = iget5_locked(sb, nodeid, fuse_inode_eq, fuse_inode_set,
&nodeid);
if (!inode)
return NULL;
A NULL root makes get_fuse_inode() a container_of() on NULL and the
nlookup decrement a write to a bogus address, oopsing the mount. With
CONFIG_KASAN the following null pointer dereference is reported when the
root inode allocation of an auto-submount fails (e.g. under memory
pressure):
==================================================================
BUG: KASAN: null-ptr-deref in fuse_get_tree_submount+0x656/0x8b0
Read of size 8 at addr 00000000000002b0 by task ls/942
CPU: 0 PID: 942 Comm: ls Tainted: G W 6.6 #15
Call Trace:
<TASK>
fuse_get_tree_submount+0x656/0x8b0
vfs_get_tree+0x48/0x140
fc_mount+0x13/0x50
fuse_dentry_automount+0x7a/0xb0
__traverse_mounts+0xca/0x330
step_into+0x339/0xac0
path_lookupat+0xc5/0x2f0
filename_lookup+0x163/0x2a0
vfs_statx+0xd5/0x200
do_statx+0x83/0xd0
__x64_sys_statx+0xa0/0xc0
do_syscall_64+0x37/0x90
entry_SYSCALL_64_after_hwframe+0x78/0xe2
</TASK>
==================================================================
Return -ENOMEM instead; the caller tears down the partially built
superblock on error, matching the other error returns in this
function. |
