| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: Prevent client use-after-free during blocked-lock reaping
A bare lock owner -- its only remaining reference a blocked lock on
nn->blocked_locks_lru -- holds a raw pointer to its nfs4_client but
no reference keeping the client alive. When the per-net laundromat
reaps such a lock, freeing the nbl drops the owner reference
held through flc_owner, and the final nfs4_put_stateowner()
takes the client's cl_lock. Because the laundromat detaches the
nbl first, __destroy_client() no longer finds it, so a concurrent
force_expire_client() can free the client before nfs4_put_stateowner()
runs, dereferencing cl_lock in freed memory.
Pin the client with cl_rpc_users before dropping
nn->blocked_locks_lock, and skip clients already expiring, whose
blocked locks __destroy_client() frees while holding an owner
reference. Take nn->client_lock outside nn->blocked_locks_lock.
Every other site holds nn->blocked_locks_lock as a leaf, acquiring
no further lock, so placing nn->client_lock outside it cannot form
a lock-order cycle. |
| In the Linux kernel, the following vulnerability has been resolved:
media: usbtv: keep device alive while ALSA card exists
The ALSA PCM callbacks store the driver state in pcm->private_data. An
open PCM file can outlive USB disconnect because usbtv_audio_free() uses
snd_card_free_when_closed(). The disconnect path can then drop the V4L2
device reference and free struct usbtv before ALSA releases the substream,
so a later close dereferences freed memory in snd_usbtv_pcm_close().
Take a V4L2 device reference for the ALSA card and drop it from the card
private_free callback. This keeps struct usbtv valid until ALSA has closed
the remaining files and freed the card. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: dwc3: clear forceRM when issuing EndTransfer
The forceRM bit of the DEPCMD register controls the behavior of the
EndTransfer command used to stop an active transfer. Older DWC3
programming guide revisions recommended setting forceRM=1 when
issuing EndTransfer. Newer programming guide revisions recommend
issuing EndTransfer with forceRM cleared.
With forceRM=1 on DWC_usb31 v2.00a and v2.10a controllers, a transfer
aborted through the ep_dequeue path was observed to remain active
after EndTransfer completion. A subsequent StartTransfer issued on the
same endpoint triggered writes associated with the aborted transfer.
This resulted in an SMMU fault because the transfer buffer had already
been unmapped during EndTransfer command-completion cleanup.
Using forceRM=0 eliminates the issue. Although older DWC3 programming
guide revisions recommended setting forceRM=1, no issues are known
from using forceRM=0. Clear forceRM when issuing EndTransfer to provide
consistent EndTransfer behavior and align with newer programming guide
recommendations. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: qcom-pmic-typec: disable cc_debounce_dwork on stop
cc_debounce_dwork is queued from the set_cc() and start_toggling()
callbacks, which run from TCPM's kthread worker. port_stop() returns
before tcpm_unregister_port() destroys that worker. Flushing the worker
during unregister may therefore run a callback which queues the delayed
work after port_stop() has returned.
The delayed work can then run after devres has freed pmic_typec_port.
Use disable_delayed_work_sync() in port_stop() to cancel a pending
instance and prevent the TCPM callbacks from queueing another one.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: qcom-pmic: cancel reset_work on stop
pdphy_stop() disables IRQs but leaves reset_work pending. If the IRQ
handler schedules it just before disable_irq(), the work runs after
remove() frees the struct via devm.
Call cancel_work_sync() after disabling IRQs to close the window.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: ucsi: displayport: Fix OOB altmode array index
The UCSI displayport driver indexes the connector's port altmode array
with the GET_CURRENT_CAM response after checking it is not 0xff. The
port altmode array is UCSI_MAX_ALTMODES elements long. If the PPM
returns an invalid GET_CURRENT_CAM response above UCSI_MAX_ALTMODES and
not equal to 0xff, the kernel may crash with an array index OOB error.
Update the UCSI displayport driver to verify the current cam is less
than UCSI_MAX_ALTMODES before accessing the port altmode array. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_midi2: fix use-after-free in string attribute show path
f_midi2_opts_str_show() takes the string lock internally, but its
callers dereference the opts->info.<field> pointer before calling it,
outside the lock. This races with f_midi2_opts_str_store(), which
frees the old string under opts->lock when the attribute is written
concurrently, the show path can read a pointer that gets freed
before the lock inside str_show() is even taken.
Change f_midi2_opts_str_show() to take a pointer to the string field,
matching the existing pattern in f_midi2_opts_str_store(), and
dereference it only after the lock is held. Update all three callers
(iface_name, block name, and the EP string option macro) accordingly. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB read / stack overflow in rtw_get_wps_attr()
rtw_get_wps_attr() walks WPS attributes inside a WPS IE taken from
a wireless management frame. For each candidate attribute it only
checks that the fixed 4-byte attribute header (2-byte ID + 2-byte
length) fits inside the IE:
if (attr_ptr + 4 > wps_ie + wps_ielen)
break;
u16 attr_id = get_unaligned_be16(attr_ptr);
u16 attr_data_len = get_unaligned_be16(attr_ptr + 2);
u16 attr_len = attr_data_len + 4;
attr_data_len (and therefore attr_len) is read directly from the
wire and is never checked against the remaining bytes in the IE
before being used as the size of:
memcpy(buf_attr, attr_ptr, attr_len);
Since attr_len is fully attacker controlled (0 to 65535+4), this is
both a heap OOB read of wps_ie, and, more seriously, a stack buffer
overflow at several call sites where buf_attr is a single-byte
stack variable, e.g. rtw_get_wps_attr_content()'s callers passing
WPS_ATTR_SELECTED_REGISTRAR into a stack "u8 sr"/"u8
selected_registrar" (drivers/staging/rtl8723bs/os_dep/ioctl_cfg80211.c,
drivers/staging/rtl8723bs/core/rtw_mlme_ext.c). A crafted WPS IE in a
beacon or probe response processed during scanning can therefore
smash the stack of the parsing thread.
rtw_get_wps_attr_content() itself has no independent length check
and simply trusts the attr_len it gets back from rtw_get_wps_attr(),
so fixing the bound here also fixes that caller.
The "attr_ptr + 4 > wps_ie + wps_ielen" header check above was added
by commit 1463ca3ec6601 ("staging: rtl8723bs: fix OOB reads in
rtw_get_sec_ie(), rtw_get_wapi_ie(), and rtw_get_wps_attr()"), which
bounded the fixed header but never extended the check to cover the
variable-length attribute data that follows it. Add that missing
check before attr_len is used as a memcpy() length or accepted as a
match. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB read in rtw_action_frame_parse()
rtw_action_frame_parse() takes a frame_len parameter but never
actually checks it before indexing into the frame body:
const u8 *frame_body = frame + sizeof(struct ieee80211_hdr_3addr);
...
c = frame_body[0];
...
a = frame_body[1];
frame_body already points 24 bytes (sizeof(struct
ieee80211_hdr_3addr)) into frame, so reading frame_body[0] and
frame_body[1] requires frame_len >= 26. A management action frame
shorter than that (e.g. exactly 24 bytes, the minimum a malicious
peer can send) causes a 1-2 byte out-of-bounds read.
This is reachable from rtw_cfg80211_monitor_if_xmit_entry() and
cfg80211_rtw_mgmt_tx() in ioctl_cfg80211.c, both of which pass
attacker/user-influenced frame buffers and lengths straight through.
Add the missing length check before frame_body is dereferenced. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB read in rtw_restruct_wmm_ie()
rtw_restruct_wmm_ie() scans in_ie for a WMM IE with:
while (i < in_len) {
...
if (i + 5 < in_len && in_ie[i] == 0xDD && ...) {
...
break;
}
i += (in_ie[i + 1] + 2); /* to the next IE element */
}
When the "i + 5 < in_len" match check fails simply because i is
within 5 bytes of the end of the buffer (i.e. no WMM IE was found
near the tail of in_ie), execution falls through to
"i += (in_ie[i + 1] + 2)", which reads in_ie[i + 1]. If i == in_len
- 1 at that point, this is a 1-byte out-of-bounds read of an
attacker-influenced IE buffer built from association/scan data.
Commit a75281626fc8f ("staging: rtl8723bs: fix potential
out-of-bounds read in rtw_restruct_wmm_ie") added the "i + 5 <
in_len" guard to the match condition itself, but did not add an
equivalent guard before the fallthrough advance, so the same class
of OOB read remained reachable through the non-matching path.
Add an explicit bounds check before advancing to the next IE. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Have show_event_filters/triggers files take trace array ref
The newly added files show_event_filters and show_event_triggers that show
all filters or triggers that are set within the trace array do not take a
reference for the trace array it is showing. Without taking a reference,
the trace_array may be freed via "rmdir" while a task is reading one of
theses files. Those files iterate all the events within an instance
(trace_array) and nothing prevents that instance from being freed while
its data is being read. This causes a use-after-free crash.
Have the open of both those files take the trace_array reference via the
trace_array_get() that prevents the trace_array from being freed while the
files are opened. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Take trace_array reference when opening options file
The options files do not take the trace_array reference for the options
they represent. This could cause a use-after-free kernel crash if one of
these files is opened by one task and another task removes the instance
that the option is for. Because it doesn't take a reference upon opening,
it will not stop the removal which will free the options descriptor that
is being used.
As the options are somewhat dynamic in their creation at boot up, each
file represents a flag in the trace_array. The trace_array has an array of
indexes to represent each of these flags that is stored in the
trace_flags_index array. The address of the index array element is used to
pass to the inode->i_private pointer. Then that element is read which
holds the index (which represents the flag) and then the index is used to
calculate the trace_array descriptor from its trace_flags_index array.
One issue is that the index element can not be referenced until the
trace_array's reference is taken. To handle this, create a new helper
function called: trace_array_options_get() that will iterate all the
existing trace_arrays in the ftrace_trace_arrays list (under the
trace_types_lock), and compare the passed in address of the index element
with the entire array of the trace_array's trace_flags_index array.
If it matches, then up the corresponding trace_array's reference and
return. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: Fix DMA mapping ownership on partial map failure
If RX mapping fails after TX mapping succeeds, __spi_map_msg() unmaps
TX but leaves tx_sg_mapped set. If TX mapping fails on a later
transfer, mappings created for earlier transfers remain active.
In both cases, cur_{tx,rx}_dma_dev have not yet been updated because they
are assigned only after every transfer has been mapped. The subsequent
spi_unmap_msg() may therefore unmap the TX mapping again or release
earlier mappings using a NULL or stale device. Using a NULL device can
trigger an oops. An empty SG table does not prevent the NULL dereference
because dma_unmap_sg_attrs() accesses the device before checking the
entry count.
Publish both mapping devices before mapping starts and unwind all
failures through __spi_unmap_msg(). This clears the mapping flags and
releases each mapping once with the device that created it.
Publishing the devices before the loop also refreshes them when no
transfer needs mapping. No mapping flag is set in that case, so current
users do not use the pointers as mapping owners. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: iscsi: Reserve a terminator byte for the login payload
iscsi_target_check_login_request() rejects a login PDU whose
DataSegmentLength exceeds MAX_KEY_VALUE_PAIRS, but the test is '>' and
login->req_buf is allocated with exactly MAX_KEY_VALUE_PAIRS
bytes. Since iscsit_get_login_rx() receives payload_length + padding
bytes, where
padding = ((-payload_length) & 3);
any payload_length from 8189 to 8192 fills the whole 8192 byte
buffer. The write stays in bounds, but no byte is left for a NUL
terminator.
The buffer is subsequently consumed as a C string. In the CHAP path
chap_check_algorithm() calls kstrdup(a_str), and extract_param() calls
strstr(in_buf, pattern) followed by strlen_semi(), none of which take a
length. convert_null_to_semi() additionally rewrites every embedded NUL
to ';', so even a payload made of well formed NUL separated key=value
records is left without a terminator. These walk past the end of the
object into adjacent slab memory. It is reachable by an unauthenticated
initiator against a portal configured for CHAP; when authentication is
not required iscsi_login_zero_tsih_s2() rewrites AuthMethod to None and
the CHAP path is never entered.
Allocate one extra byte. kzalloc() zeroes it and nothing ever writes to
it, as every writer copies to offset 0 for at most MAX_KEY_VALUE_PAIRS
bytes, so the buffer is always terminated. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: bsg: Cap io_uring sense copy to max_response_len
Completion copied scmd->sense_len to the user response buffer without
honoring max_response_len. After a valid sense, the midlayer sets
sense_len to the real length (up to SCSI_SENSE_BUFFERSIZE), so a smaller
user buffer was overrun. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: bsg: Fix TOCTOU in io_uring passthrough command setup
scsi_bsg_uring_cmd() reads bsg_uring_cmd from the shared mmap'd SQE.
Userspace can change a field after we check it and before we use it.
request_len is the sharp case: it can grow past sizeof(scmd->cmnd) after
the bound check and overflow scmd->cmnd in copy_from_user().
READ_ONCE() the SQE fields we check or use into locals before use. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: megaraid_sas: Limit NVMe request size to the PRP chain frame
megasas_make_prp_nvme() builds a command's PRP list in cmd->sg_frame, a
DMA pool buffer of instance->max_chain_frame_sz bytes, spending one
entry per NVMe page of the transfer plus one per page of the buffer for
the chain pointer. The loop runs until the transfer is described and
never checks the buffer bound.
max_hw_sectors comes straight from the MDTS the firmware reports for the
drive. On drives with a large MDTS the only thing keeping the list
inside the buffer was the block layer default of 1280 KiB, which needs
320 entries, which fit into a 4 KiB frame as that holds 512. But since
commit 9b8b84879d4a ("block: Increase BLK_DEF_MAX_SECTORS_CAP") that
default is 4 MiB, and such a transfer needs 1025 entries, so the list
runs a full page past the end of the frame:
sd 1:0:1:0: [sdb] tag#630 page boundary ptr_sgl: 0x00000000ba62d13f
BUG: unable to handle page fault for address: ff663bcb81e7c000
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
RIP: 0010:megasas_build_and_issue_cmd_fusion+0xeaa/0x1870 [megaraid_sas]
If the page after the frame happens to be mapped, the overrun does not
fault but silently corrupts the neighbouring pool entry, which is
another in-flight command's PRP list.
Cap max_hw_sectors at what the chain frame can describe, less one page
for transfers that do not start on a page boundary and so need one entry
more. This is the megaraid_sas counterpart of commit 04631f55afc5
("scsi: mpt3sas: Limit NVMe request size to 2 MiB"), but derives the
limit from max_chain_frame_sz rather than hardcoding it. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: pm8001: Use rollback index when freeing MSI-X vectors
pm8001_request_msix() unwinds previously registered handlers with
free_irq() when request_irq() fails. The rollback loop uses the failing
index i for every iteration instead of the already registered vector
index j.
That passes the wrong IRQ/dev_id pair to free_irq() and leaves the
earlier handlers installed. Use j for both pci_irq_vector() and the
matching irq_vector entry in the rollback loop. |
| In the Linux kernel, the following vulnerability has been resolved:
futex: Prevent rcuwait use-after-free during requeue PI
On PREEMPT_RT, FUTEX_CMP_REQUEUE_PI can trigger a KASAN report
(slab-out-of-bounds) in futex_requeue_pi_complete() invocation of
rcuwait_wake_up().
The futex_q used by futex_wait_requeue_pi() is allocated on the waiter's
stack. An early wakeup can race with a PI requeue as follows:
waiter requeue task
------ ------------
futex_wait_requeue_pi()
futex_do_wait()
schedule()
futex_requeue
futex_proxy_trylock_atomic()
futex_requeue_pi_prepare()
Q_REQUEUE_PI_NONE -> Q_REQUEUE_PI_IN_PROGRESS
* timeout/ signal wakes waiter *
futex_requeue_pi_wakeup_sync()
Q_REQUEUE_PI_IN_PROGRESS -> Q_REQUEUE_PI_WAIT
requeue_pi_wake_futex
futex_requeue_pi_complete()
cmpxchg Q_REQUEUE_PI_WAIT -> Q_REQUEUE_PI_LOCKED
rcuwait_wait_event()
if (atomic_read(&q->requeue_state) != Q_REQUEUE_PI_WAIT)
break /* no schedule() */
/* q.pi_state->owner == current */
futex_private_hash_put()
/* return from syscall */
rcuwait_wake_up(&q->requeue_wait)
/* q is gone */
futex_requeue_pi_complete() publishes Q_REQUEUE_PI_LOCKED before
calling rcuwait_wake_up(). The waiter observes this state in
rcuwait_wait_event() before invoking schedule() in rcuwait_wait_event().
Here, the waiter is free leave the syscall before requeue task can
complete the wake.
To address this race skip rcuwait_wake_up() in the Q_REQUEUE_PI_LOCKED
case.
This state is only published by requeue_pi_wake_futex(), which saves
q->task before futex_requeue_pi_complete() and wakes the waiter via
wake_up_state().
This wake is intended to wake the waiter from its futex_do_wait() sleep.
If the waiter is still sleeping there, it can not get into the
Q_REQUEUE_PI_WAIT state (and require this removed wake).
Should the waiter be woken up from futex_do_wait() by other means (as in
this example) and sleep in futex_requeue_pi_wakeup_sync() then the
wake_up_state() from requeue_pi_wake_futex() will wake it, too.
Should the waiter task terminate before wake_up_state() had a chance to
wake the task then the task pointer does not become invalid because the
futex_hash_bucket::lock is held and the task pointer is RCU protected.
[bigeasy: Updated comment and commit message] |
| In the Linux kernel, the following vulnerability has been resolved:
ftrace: Take trace_array reference before accessing its ftrace_ops
The trace instance files set_ftrace_filter and set_ftrace_notrace was
updated to work with specific trace instances (trace_arrays). The issue is
that when these files are opened, there is a small race window where it
will use the ftrace_ops from the inode->private pointer to get a reference
to the trace_array and then take its reference. The problem is that the
ftrace_ops itself could be freed. If the rmdir on the instance happens at
the same time the set_ftrace_filter file is opened, the rmdir could have
also freed the ftrace_ops and referencing it will cause a use-after-free
bug and crash the kernel.
Instead, pass in the trace_array as the file private data (NULL for the
top level instance), and then pass both the trace_array and the ftrace_ops
to the ftrace_regex_open() function. If the trace_array is NULL, then it
just uses the ftrace_ops without the need to take its reference (like
normal). If the ftrace_ops is NULL, that is only the case for the top
level instance and the global_ops can be used.
This allows the trace_array to have its reference incremented before
touching the ftrace_ops that could also be freed when the instance is. |
