| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: timer: Set lower bound of start tick time
Currently ALSA timer doesn't have the lower limit of the start tick
time, and it allows a very small size, e.g. 1 tick with 1ns resolution
for hrtimer. Such a situation may lead to an unexpected RCU stall,
where the callback repeatedly queuing the expire update, as reported
by fuzzer.
This patch introduces a sanity check of the timer start tick time, so
that the system returns an error when a too small start size is set.
As of this patch, the lower limit is hard-coded to 100us, which is
small enough but can still work somehow. |
| In the Linux kernel, the following vulnerability has been resolved:
firewire: ohci: mask bus reset interrupts between ISR and bottom half
In the FireWire OHCI interrupt handler, if a bus reset interrupt has
occurred, mask bus reset interrupts until bus_reset_work has serviced and
cleared the interrupt.
Normally, we always leave bus reset interrupts masked. We infer the bus
reset from the self-ID interrupt that happens shortly thereafter. A
scenario where we unmask bus reset interrupts was introduced in 2008 in
a007bb857e0b26f5d8b73c2ff90782d9c0972620: If
OHCI_PARAM_DEBUG_BUSRESETS (8) is set in the debug parameter bitmask, we
will unmask bus reset interrupts so we can log them.
irq_handler logs the bus reset interrupt. However, we can't clear the bus
reset event flag in irq_handler, because we won't service the event until
later. irq_handler exits with the event flag still set. If the
corresponding interrupt is still unmasked, the first bus reset will
usually freeze the system due to irq_handler being called again each
time it exits. This freeze can be reproduced by loading firewire_ohci
with "modprobe firewire_ohci debug=-1" (to enable all debugging output).
Apparently there are also some cases where bus_reset_work will get called
soon enough to clear the event, and operation will continue normally.
This freeze was first reported a few months after a007bb85 was committed,
but until now it was never fixed. The debug level could safely be set
to -1 through sysfs after the module was loaded, but this would be
ineffectual in logging bus reset interrupts since they were only
unmasked during initialization.
irq_handler will now leave the event flag set but mask bus reset
interrupts, so irq_handler won't be called again and there will be no
freeze. If OHCI_PARAM_DEBUG_BUSRESETS is enabled, bus_reset_work will
unmask the interrupt after servicing the event, so future interrupts
will be caught as desired.
As a side effect to this change, OHCI_PARAM_DEBUG_BUSRESETS can now be
enabled through sysfs in addition to during initial module loading.
However, when enabled through sysfs, logging of bus reset interrupts will
be effective only starting with the second bus reset, after
bus_reset_work has executed. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPI: CPPC: Use access_width over bit_width for system memory accesses
To align with ACPI 6.3+, since bit_width can be any 8-bit value, it
cannot be depended on to be always on a clean 8b boundary. This was
uncovered on the Cobalt 100 platform.
SError Interrupt on CPU26, code 0xbe000011 -- SError
CPU: 26 PID: 1510 Comm: systemd-udevd Not tainted 5.15.2.1-13 #1
Hardware name: MICROSOFT CORPORATION, BIOS MICROSOFT CORPORATION
pstate: 62400009 (nZCv daif +PAN -UAO +TCO -DIT -SSBS BTYPE=--)
pc : cppc_get_perf_caps+0xec/0x410
lr : cppc_get_perf_caps+0xe8/0x410
sp : ffff8000155ab730
x29: ffff8000155ab730 x28: ffff0080139d0038 x27: ffff0080139d0078
x26: 0000000000000000 x25: ffff0080139d0058 x24: 00000000ffffffff
x23: ffff0080139d0298 x22: ffff0080139d0278 x21: 0000000000000000
x20: ffff00802b251910 x19: ffff0080139d0000 x18: ffffffffffffffff
x17: 0000000000000000 x16: ffffdc7e111bad04 x15: ffff00802b251008
x14: ffffffffffffffff x13: ffff013f1fd63300 x12: 0000000000000006
x11: ffffdc7e128f4420 x10: 0000000000000000 x9 : ffffdc7e111badec
x8 : ffff00802b251980 x7 : 0000000000000000 x6 : ffff0080139d0028
x5 : 0000000000000000 x4 : ffff0080139d0018 x3 : 00000000ffffffff
x2 : 0000000000000008 x1 : ffff8000155ab7a0 x0 : 0000000000000000
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 26 PID: 1510 Comm: systemd-udevd Not tainted
5.15.2.1-13 #1
Hardware name: MICROSOFT CORPORATION, BIOS MICROSOFT CORPORATION
Call trace:
dump_backtrace+0x0/0x1e0
show_stack+0x24/0x30
dump_stack_lvl+0x8c/0xb8
dump_stack+0x18/0x34
panic+0x16c/0x384
add_taint+0x0/0xc0
arm64_serror_panic+0x7c/0x90
arm64_is_fatal_ras_serror+0x34/0xa4
do_serror+0x50/0x6c
el1h_64_error_handler+0x40/0x74
el1h_64_error+0x7c/0x80
cppc_get_perf_caps+0xec/0x410
cppc_cpufreq_cpu_init+0x74/0x400 [cppc_cpufreq]
cpufreq_online+0x2dc/0xa30
cpufreq_add_dev+0xc0/0xd4
subsys_interface_register+0x134/0x14c
cpufreq_register_driver+0x1b0/0x354
cppc_cpufreq_init+0x1a8/0x1000 [cppc_cpufreq]
do_one_initcall+0x50/0x250
do_init_module+0x60/0x27c
load_module+0x2300/0x2570
__do_sys_finit_module+0xa8/0x114
__arm64_sys_finit_module+0x2c/0x3c
invoke_syscall+0x78/0x100
el0_svc_common.constprop.0+0x180/0x1a0
do_el0_svc+0x84/0xa0
el0_svc+0x2c/0xc0
el0t_64_sync_handler+0xa4/0x12c
el0t_64_sync+0x1a4/0x1a8
Instead, use access_width to determine the size and use the offset and
width to shift and mask the bits to read/write out. Make sure to add a
check for system memory since pcc redefines the access_width to
subspace id.
If access_width is not set, then fall back to using bit_width.
[ rjw: Subject and changelog edits, comment adjustments ] |
| In the Linux kernel, the following vulnerability has been resolved:
dyndbg: fix old BUG_ON in >control parser
Fix a BUG_ON from 2009. Even if it looks "unreachable" (I didn't
really look), lets make sure by removing it, doing pr_err and return
-EINVAL instead. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: udc: remove warning when queue disabled ep
It is possible trigger below warning message from mass storage function,
WARNING: CPU: 6 PID: 3839 at drivers/usb/gadget/udc/core.c:294 usb_ep_queue+0x7c/0x104
pc : usb_ep_queue+0x7c/0x104
lr : fsg_main_thread+0x494/0x1b3c
Root cause is mass storage function try to queue request from main thread,
but other thread may already disable ep when function disable.
As there is no function failure in the driver, in order to avoid effort
to fix warning, change WARN_ON_ONCE() in usb_ep_queue() to pr_debug(). |
| In the Linux kernel, the following vulnerability has been resolved:
x86/efistub: Call mixed mode boot services on the firmware's stack
Normally, the EFI stub calls into the EFI boot services using the stack
that was live when the stub was entered. According to the UEFI spec,
this stack needs to be at least 128k in size - this might seem large but
all asynchronous processing and event handling in EFI runs from the same
stack and so quite a lot of space may be used in practice.
In mixed mode, the situation is a bit different: the bootloader calls
the 32-bit EFI stub entry point, which calls the decompressor's 32-bit
entry point, where the boot stack is set up, using a fixed allocation
of 16k. This stack is still in use when the EFI stub is started in
64-bit mode, and so all calls back into the EFI firmware will be using
the decompressor's limited boot stack.
Due to the placement of the boot stack right after the boot heap, any
stack overruns have gone unnoticed. However, commit
5c4feadb0011983b ("x86/decompressor: Move global symbol references to C code")
moved the definition of the boot heap into C code, and now the boot
stack is placed right at the base of BSS, where any overruns will
corrupt the end of the .data section.
While it would be possible to work around this by increasing the size of
the boot stack, doing so would affect all x86 systems, and mixed mode
systems are a tiny (and shrinking) fraction of the x86 installed base.
So instead, record the firmware stack pointer value when entering from
the 32-bit firmware, and switch to this stack every time a EFI boot
service call is made. |
| In the Linux kernel, the following vulnerability has been resolved:
block: Fix WARNING in _copy_from_iter
Syzkaller reports a warning in _copy_from_iter because an
iov_iter is supposedly used in the wrong direction. The reason
is that syzcaller managed to generate a request with
a transfer direction of SG_DXFER_TO_FROM_DEV. This instructs
the kernel to copy user buffers into the kernel, read into
the copied buffers and then copy the data back to user space.
Thus the iovec is used in both directions.
Detect this situation in the block layer and construct a new
iterator with the correct direction for the copy-in. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/aio: Restrict kiocb_set_cancel_fn() to I/O submitted via libaio
If kiocb_set_cancel_fn() is called for I/O submitted via io_uring, the
following kernel warning appears:
WARNING: CPU: 3 PID: 368 at fs/aio.c:598 kiocb_set_cancel_fn+0x9c/0xa8
Call trace:
kiocb_set_cancel_fn+0x9c/0xa8
ffs_epfile_read_iter+0x144/0x1d0
io_read+0x19c/0x498
io_issue_sqe+0x118/0x27c
io_submit_sqes+0x25c/0x5fc
__arm64_sys_io_uring_enter+0x104/0xab0
invoke_syscall+0x58/0x11c
el0_svc_common+0xb4/0xf4
do_el0_svc+0x2c/0xb0
el0_svc+0x2c/0xa4
el0t_64_sync_handler+0x68/0xb4
el0t_64_sync+0x1a4/0x1a8
Fix this by setting the IOCB_AIO_RW flag for read and write I/O that is
submitted by libaio. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPICA: Avoid undefined behavior: applying zero offset to null pointer
ACPICA commit 770653e3ba67c30a629ca7d12e352d83c2541b1e
Before this change we see the following UBSAN stack trace in Fuchsia:
#0 0x000021e4213b3302 in acpi_ds_init_aml_walk(struct acpi_walk_state*, union acpi_parse_object*, struct acpi_namespace_node*, u8*, u32, struct acpi_evaluate_info*, u8) ../../third_party/acpica/source/components/dispatcher/dswstate.c:682 <platform-bus-x86.so>+0x233302
#1.2 0x000020d0f660777f in ubsan_get_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:41 <libclang_rt.asan.so>+0x3d77f
#1.1 0x000020d0f660777f in maybe_print_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:51 <libclang_rt.asan.so>+0x3d77f
#1 0x000020d0f660777f in ~scoped_report() compiler-rt/lib/ubsan/ubsan_diag.cpp:387 <libclang_rt.asan.so>+0x3d77f
#2 0x000020d0f660b96d in handlepointer_overflow_impl() compiler-rt/lib/ubsan/ubsan_handlers.cpp:809 <libclang_rt.asan.so>+0x4196d
#3 0x000020d0f660b50d in compiler-rt/lib/ubsan/ubsan_handlers.cpp:815 <libclang_rt.asan.so>+0x4150d
#4 0x000021e4213b3302 in acpi_ds_init_aml_walk(struct acpi_walk_state*, union acpi_parse_object*, struct acpi_namespace_node*, u8*, u32, struct acpi_evaluate_info*, u8) ../../third_party/acpica/source/components/dispatcher/dswstate.c:682 <platform-bus-x86.so>+0x233302
#5 0x000021e4213e2369 in acpi_ds_call_control_method(struct acpi_thread_state*, struct acpi_walk_state*, union acpi_parse_object*) ../../third_party/acpica/source/components/dispatcher/dsmethod.c:605 <platform-bus-x86.so>+0x262369
#6 0x000021e421437fac in acpi_ps_parse_aml(struct acpi_walk_state*) ../../third_party/acpica/source/components/parser/psparse.c:550 <platform-bus-x86.so>+0x2b7fac
#7 0x000021e4214464d2 in acpi_ps_execute_method(struct acpi_evaluate_info*) ../../third_party/acpica/source/components/parser/psxface.c:244 <platform-bus-x86.so>+0x2c64d2
#8 0x000021e4213aa052 in acpi_ns_evaluate(struct acpi_evaluate_info*) ../../third_party/acpica/source/components/namespace/nseval.c:250 <platform-bus-x86.so>+0x22a052
#9 0x000021e421413dd8 in acpi_ns_init_one_device(acpi_handle, u32, void*, void**) ../../third_party/acpica/source/components/namespace/nsinit.c:735 <platform-bus-x86.so>+0x293dd8
#10 0x000021e421429e98 in acpi_ns_walk_namespace(acpi_object_type, acpi_handle, u32, u32, acpi_walk_callback, acpi_walk_callback, void*, void**) ../../third_party/acpica/source/components/namespace/nswalk.c:298 <platform-bus-x86.so>+0x2a9e98
#11 0x000021e4214131ac in acpi_ns_initialize_devices(u32) ../../third_party/acpica/source/components/namespace/nsinit.c:268 <platform-bus-x86.so>+0x2931ac
#12 0x000021e42147c40d in acpi_initialize_objects(u32) ../../third_party/acpica/source/components/utilities/utxfinit.c:304 <platform-bus-x86.so>+0x2fc40d
#13 0x000021e42126d603 in acpi::acpi_impl::initialize_acpi(acpi::acpi_impl*) ../../src/devices/board/lib/acpi/acpi-impl.cc:224 <platform-bus-x86.so>+0xed603
Add a simple check that avoids incrementing a pointer by zero, but
otherwise behaves as before. Note that our findings are against ACPICA
20221020, but the same code exists on master. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: zero i_disksize when initializing the bootloader inode
If the boot loader inode has never been used before, the
EXT4_IOC_SWAP_BOOT inode will initialize it, including setting the
i_size to 0. However, if the "never before used" boot loader has a
non-zero i_size, then i_disksize will be non-zero, and the
inconsistency between i_size and i_disksize can trigger a kernel
warning:
WARNING: CPU: 0 PID: 2580 at fs/ext4/file.c:319
CPU: 0 PID: 2580 Comm: bb Not tainted 6.3.0-rc1-00004-g703695902cfa
RIP: 0010:ext4_file_write_iter+0xbc7/0xd10
Call Trace:
vfs_write+0x3b1/0x5c0
ksys_write+0x77/0x160
__x64_sys_write+0x22/0x30
do_syscall_64+0x39/0x80
Reproducer:
1. create corrupted image and mount it:
mke2fs -t ext4 /tmp/foo.img 200
debugfs -wR "sif <5> size 25700" /tmp/foo.img
mount -t ext4 /tmp/foo.img /mnt
cd /mnt
echo 123 > file
2. Run the reproducer program:
posix_memalign(&buf, 1024, 1024)
fd = open("file", O_RDWR | O_DIRECT);
ioctl(fd, EXT4_IOC_SWAP_BOOT);
write(fd, buf, 1024);
Fix this by setting i_disksize as well as i_size to zero when
initiaizing the boot loader inode. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Perform lockless command completion in abort path
While adding and removing the controller, the following call trace was
observed:
WARNING: CPU: 3 PID: 623596 at kernel/dma/mapping.c:532 dma_free_attrs+0x33/0x50
CPU: 3 PID: 623596 Comm: sh Kdump: loaded Not tainted 5.14.0-96.el9.x86_64 #1
RIP: 0010:dma_free_attrs+0x33/0x50
Call Trace:
qla2x00_async_sns_sp_done+0x107/0x1b0 [qla2xxx]
qla2x00_abort_srb+0x8e/0x250 [qla2xxx]
? ql_dbg+0x70/0x100 [qla2xxx]
__qla2x00_abort_all_cmds+0x108/0x190 [qla2xxx]
qla2x00_abort_all_cmds+0x24/0x70 [qla2xxx]
qla2x00_abort_isp_cleanup+0x305/0x3e0 [qla2xxx]
qla2x00_remove_one+0x364/0x400 [qla2xxx]
pci_device_remove+0x36/0xa0
__device_release_driver+0x17a/0x230
device_release_driver+0x24/0x30
pci_stop_bus_device+0x68/0x90
pci_stop_and_remove_bus_device_locked+0x16/0x30
remove_store+0x75/0x90
kernfs_fop_write_iter+0x11c/0x1b0
new_sync_write+0x11f/0x1b0
vfs_write+0x1eb/0x280
ksys_write+0x5f/0xe0
do_syscall_64+0x5c/0x80
? do_user_addr_fault+0x1d8/0x680
? do_syscall_64+0x69/0x80
? exc_page_fault+0x62/0x140
? asm_exc_page_fault+0x8/0x30
entry_SYSCALL_64_after_hwframe+0x44/0xae
The command was completed in the abort path during driver unload with a
lock held, causing the warning in abort path. Hence complete the command
without any lock held. |
| In the Linux kernel, the following vulnerability has been resolved:
ca8210: fix mac_len negative array access
This patch fixes a buffer overflow access of skb->data if
ieee802154_hdr_peek_addrs() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
nilfs2: fix general protection fault in nilfs_btree_insert()
If nilfs2 reads a corrupted disk image and tries to reads a b-tree node
block by calling __nilfs_btree_get_block() against an invalid virtual
block address, it returns -ENOENT because conversion of the virtual block
address to a disk block address fails. However, this return value is the
same as the internal code that b-tree lookup routines return to indicate
that the block being searched does not exist, so functions that operate on
that b-tree may misbehave.
When nilfs_btree_insert() receives this spurious 'not found' code from
nilfs_btree_do_lookup(), it misunderstands that the 'not found' check was
successful and continues the insert operation using incomplete lookup path
data, causing the following crash:
general protection fault, probably for non-canonical address
0xdffffc0000000005: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f]
...
RIP: 0010:nilfs_btree_get_nonroot_node fs/nilfs2/btree.c:418 [inline]
RIP: 0010:nilfs_btree_prepare_insert fs/nilfs2/btree.c:1077 [inline]
RIP: 0010:nilfs_btree_insert+0x6d3/0x1c10 fs/nilfs2/btree.c:1238
Code: bc 24 80 00 00 00 4c 89 f8 48 c1 e8 03 42 80 3c 28 00 74 08 4c 89
ff e8 4b 02 92 fe 4d 8b 3f 49 83 c7 28 4c 89 f8 48 c1 e8 03 <42> 80 3c
28 00 74 08 4c 89 ff e8 2e 02 92 fe 4d 8b 3f 49 83 c7 02
...
Call Trace:
<TASK>
nilfs_bmap_do_insert fs/nilfs2/bmap.c:121 [inline]
nilfs_bmap_insert+0x20d/0x360 fs/nilfs2/bmap.c:147
nilfs_get_block+0x414/0x8d0 fs/nilfs2/inode.c:101
__block_write_begin_int+0x54c/0x1a80 fs/buffer.c:1991
__block_write_begin fs/buffer.c:2041 [inline]
block_write_begin+0x93/0x1e0 fs/buffer.c:2102
nilfs_write_begin+0x9c/0x110 fs/nilfs2/inode.c:261
generic_perform_write+0x2e4/0x5e0 mm/filemap.c:3772
__generic_file_write_iter+0x176/0x400 mm/filemap.c:3900
generic_file_write_iter+0xab/0x310 mm/filemap.c:3932
call_write_iter include/linux/fs.h:2186 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x7dc/0xc50 fs/read_write.c:584
ksys_write+0x177/0x2a0 fs/read_write.c:637
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
...
</TASK>
This patch fixes the root cause of this problem by replacing the error
code that __nilfs_btree_get_block() returns on block address conversion
failure from -ENOENT to another internal code -EINVAL which means that the
b-tree metadata is corrupted.
By returning -EINVAL, it propagates without glitches, and for all relevant
b-tree operations, functions in the upper bmap layer output an error
message indicating corrupted b-tree metadata via
nilfs_bmap_convert_error(), and code -EIO will be eventually returned as
it should be. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Detect IP == ksym.end as part of BPF program
Now that bpf_throw kfunc is the first such call instruction that has
noreturn semantics within the verifier, this also kicks in dead code
elimination in unprecedented ways. For one, any instruction following
a bpf_throw call will never be marked as seen. Moreover, if a callchain
ends up throwing, any instructions after the call instruction to the
eventually throwing subprog in callers will also never be marked as
seen.
The tempting way to fix this would be to emit extra 'int3' instructions
which bump the jited_len of a program, and ensure that during runtime
when a program throws, we can discover its boundaries even if the call
instruction to bpf_throw (or to subprogs that always throw) is emitted
as the final instruction in the program.
An example of such a program would be this:
do_something():
...
r0 = 0
exit
foo():
r1 = 0
call bpf_throw
r0 = 0
exit
bar(cond):
if r1 != 0 goto pc+2
call do_something
exit
call foo
r0 = 0 // Never seen by verifier
exit //
main(ctx):
r1 = ...
call bar
r0 = 0
exit
Here, if we do end up throwing, the stacktrace would be the following:
bpf_throw
foo
bar
main
In bar, the final instruction emitted will be the call to foo, as such,
the return address will be the subsequent instruction (which the JIT
emits as int3 on x86). This will end up lying outside the jited_len of
the program, thus, when unwinding, we will fail to discover the return
address as belonging to any program and end up in a panic due to the
unreliable stack unwinding of BPF programs that we never expect.
To remedy this case, make bpf_prog_ksym_find treat IP == ksym.end as
part of the BPF program, so that is_bpf_text_address returns true when
such a case occurs, and we are able to unwind reliably when the final
instruction ends up being a call instruction. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: aqc111: check packet for fixup for true limit
If a device sends a packet that is inbetween 0
and sizeof(u64) the value passed to skb_trim()
as length will wrap around ending up as some very
large value.
The driver will then proceed to parse the header
located at that position, which will either oops or
process some random value.
The fix is to check against sizeof(u64) rather than
0, which the driver currently does. The issue exists
since the introduction of the driver. |
| In the Linux kernel, the following vulnerability has been resolved:
reiserfs: Avoid touching renamed directory if parent does not change
The VFS will not be locking moved directory if its parent does not
change. Change reiserfs rename code to avoid touching renamed directory
if its parent does not change as without locking that can corrupt the
filesystem. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: sun6i: reduce DMA RX transfer width to single byte
Through empirical testing it has been determined that sometimes RX SPI
transfers with DMA enabled return corrupted data. This is down to single
or even multiple bytes lost during DMA transfer from SPI peripheral to
memory. It seems the RX FIFO within the SPI peripheral can become
confused when performing bus read accesses wider than a single byte to it
during an active SPI transfer.
This patch reduces the width of individual DMA read accesses to the
RX FIFO to a single byte to mitigate that issue. |
| In the Linux kernel, the following vulnerability has been resolved:
gfs2: Set .migrate_folio in gfs2_{rgrp,meta}_aops
Clears up the warning added in 7ee3647243e5 ("migrate: Remove call to
->writepage") that occurs in various xfstests, causing "something found
in dmesg" failures.
[ 341.136573] gfs2_meta_aops does not implement migrate_folio
[ 341.136953] WARNING: CPU: 1 PID: 36 at mm/migrate.c:944 move_to_new_folio+0x2f8/0x300 |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: check that dummy regulator has been probed before using it
Due to asynchronous driver probing there is a chance that the dummy
regulator hasn't already been probed when first accessing it. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: ignore non-functional sensor in HP 5MP Camera
The HP 5MP Camera (USB ID 0408:5473) reports a HID sensor interface that
is not actually implemented. Attempting to access this non-functional
sensor via iio_info causes system hangs as runtime PM tries to wake up
an unresponsive sensor.
[453] hid-sensor-hub 0003:0408:5473.0003: Report latency attributes: ffffffff:ffffffff
[453] hid-sensor-hub 0003:0408:5473.0003: common attributes: 5:1, 2:1, 3:1 ffffffff:ffffffff
Add this device to the HID ignore list since the sensor interface is
non-functional by design and should not be exposed to userspace. |
