| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_ife: Only operate on Ethernet frames
act_ife encapsulates/decapsulates the original Ethernet header and uses
skb->dev->hard_header_len as the length of that header. That is only
correct for Ethernet devices: on a device where hard_header_len does not
match the L2 header that was actually pulled (PPP reports PPP_HDRLEN
while nothing is stripped on ingress), the ingress skb_push()/skb_pull()
use the wrong length and can hit skb_under_panic when headroom is tight.
IFE is Ethernet-only by design - it builds an outer ethhdr, rewrites
h_source/h_dest/h_proto, and calls eth_type_trans() on decode - so
instead of trying to make the offsets work for arbitrary link types,
simply drop packets that do not carry an Ethernet header.
Checking skb->dev->type alone is not enough. We have to cater for a
corner case where mirred can redirect an skb from a non-Ethernet device
to an Ethernet one, and skb->dev then says nothing about the framing the
skb actually has: an skb redirected from ppp0 reaches the target's ingress
hook with mac_len 0 and no Ethernet header at all. So at ingress also
require mac_len to be ETH_HLEN. On egress mac_len is not maintained, so
the device type is all we have; a bogus redirect there yields a malformed
frame rather than an out-of-bounds push, and it would be malformed with or
without IFE.
That corner case is not theoretical - redirecting from ppp0 into a veth
that has an ife encode action on its ingress hook panics without this
patch:
skbuff: skb_under_panic: len:98 put:14 head:ffff88800e410000
data:ffff88800e40fff5 tail:0x57 end:0x640 dev:veth3
kernel BUG at net/core/skbuff.c:214!
Call Trace:
skb_push (net/core/skbuff.c:224 net/core/skbuff.c:2657)
tcf_ife_act (net/sched/act_ife.c:829 net/sched/act_ife.c:874)
tc_run (net/core/dev.c:4463)
netif_receive_skb (net/core/dev.c:6463 net/core/dev.c:6522)
tcf_mirred_to_dev (net/sched/act_mirred.c:248 net/sched/act_mirred.c:328)
tcf_mirred_act (net/sched/act_mirred.c:489)
tc_run (net/core/dev.c:4463)
process_backlog (net/core/dev.c:6728)
With Ethernet framing guaranteed, use ETH_HLEN instead of
hard_header_len. |
| In the Linux kernel, the following vulnerability has been resolved:
hinic3: Fix skb linearization mismatch and drop skb when skb_checksum_help() failed
Previously, hinic3_send_one_skb() cached the skb fragment count before
calling hinic3_tx_offload(). If hinic3_tx_csum() falls back to
skb_checksum_help() for unsupported tunnel packets, the skb may be
linearized. Continuing to build the TX descriptor with the stale
fragment count leads to a descriptor mismatch, which can trigger
out-of-bounds DMA reads or IOMMU faults.
Furthermore, the old code ignored the return value of skb_checksum_help(),
transmitting corrupted packets with incomplete checksums upon failure.
Fix this by:
1. Moving the hinic3_tx_offload() call before calculating 'num_sge' to
ensure the correct fragment count is used if the SKB is linearized.
2. Propagating skb_checksum_help() errors and returning
HINIC3_TX_OFFLOAD_INVALID to properly drop the skb. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btnxpuart: Validate the FW dump header length
nxp_process_fw_dump() pulls the ACL header off the frame and then reads
seq_num and buf_len from a struct nxp_fw_dump_hdr placed at skb->data,
without checking that the ACL payload is long enough to contain it.
h4_recv_buf() collects HCI_ACL_HDR_SIZE bytes of header followed by the
number of payload bytes named in that header, so skb->len is 4 + dlen
with dlen supplied by the controller and possibly smaller than the 8
byte dump header, or zero. A short frame with connection handle 0xfff
therefore reads both fields from beyond the received data.
Beyond the read itself, buf_len is what terminates a dump: a value of
zero makes the driver call hci_devcd_complete() and reset the
controller, so a truncated frame can end a dump early.
Use skb_pull_data() to validate and pull the FW dump header before
accessing its fields. Warn and reject the chunk if the header is
truncated. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btmtksdio: Fix out-of-bounds DMA read in the TX path
btmtksdio_tx_packet() rounds the transfer size up to the SDIO block size
of 256 bytes, but hands the host controller the SKB buffer as is:
err = sdio_writesb(bdev->func, MTK_REG_CTDR, skb->data,
round_up(skb->len, MTK_SDIO_BLOCK_SIZE));
Only skb->len bytes hold packet data, so the controller reads up to 255
bytes of uninitialised memory and sends it to the device over the SDIO
bus. Depending on how much tailroom slack the SKB allocation happens to
carry, that read can also extend past the end of the buffer.
Compute the padded length up front, ensure the SKB has tailroom for it,
and zero-fill the padding with skb_put_zero(). skb->len then covers the
padding, so sdio_writesb() no longer needs to round up. byte_tx keeps
counting the header and the payload only, and the error path restores the
SKB so that the caller can requeue it.
Writing behind skb->tail is only safe because the driver owns the buffer,
which "Bluetooth: btmtksdio: Take exclusive ownership of the SKB before
TX" ensures. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSv4.2: fix LAYOUTSTATS send buffer exhaustion
encode_layoutstats_maxsz budgets XDR_QUADLEN(PNFS_LAYOUTSTATS_MAXSIZE),
i.e. 256 bytes, for the layoutupdate4 body written by the layout driver.
The flexfiles record can exceed that.
ff_layout_encode_ff_layoutupdate() emits, per data server, a netaddr4,
an nfs_fh4, two ff_io_latency4, an nfstime4 and a bool. A data server
whose filehandle is NFS_MAXFHSIZE bytes long already accounts for 132 of
those bytes, and the two ff_io_latency4 at 64 bytes each, the nfstime4
and the bool add a further 144, so the body passes 256 bytes before the
netaddr4 is encoded at all. encode_layoutstats() additionally writes
the deviceid4 and the layoutupdate4 lou_type word, neither of which the
macro accounts for.
The filehandle and the address are both chosen by the server, through
LAYOUTGET and GETDEVICEINFO, so it can drive the encoder past the
end of the send buffer. xdr_reserve_space() returns NULL once that
happens, and the two ff_layout_encode_io_latency() calls run with
dss_info->mirror->lock held, so a NULL return there leaves the lock
permanently held.
Raise PNFS_LAYOUTSTATS_MAXSIZE to 384 so that the record fits inside the
reservation. |
| In the Linux kernel, the following vulnerability has been resolved:
mailbox: riscv-sbi-mpxy: validate RPMI notification lengths
The SBI return value controls how many bytes are copied from shared
memory into the RPMI notification buffer. It is not validated against
the negotiated shared-memory size before that copy. The event walker
also uses a reversed loop condition and can inspect a short event record.
Validate the complete notification length before copying it, iterate only
while a full event header remains, and stop when a declared event payload
extends beyond the copied notification data. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject negative optlen in cgroup getsockopt hook
A cgroup getsockopt BPF program can shrink ctx->optlen after the
kernel getsockopt handler has run. The kernel-buffer variant, used by
TCP_ZEROCOPY_RECEIVE, only rejects values larger than the original
length.
If BPF writes a negative optlen, that value is accepted and propagated
back to the TCP getsockopt code. It can then be passed to
copy_to_sockptr() as a size_t and trigger the hardened usercopy
bytes > INT_MAX warning.
Reject negative ctx.optlen in __cgroup_bpf_run_filter_getsockopt_kern(),
matching the lower-bound validation already present in the sockptr-based
getsockopt hook. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SOF: validate topology volume range before allocation
SOF treats the topology mixer min and max values as non-negative indices
into its volume table. It stores them in signed fields, allocates max + 1
entries through an int argument, and later indexes the table with the
stored range.
An inverted range is invalid, while a maximum at or above INT_MAX cannot
be represented safely after the increment or in the signed fields.
Validate the complete range before storing it or allocating the table. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/tegra241-cmdqv: Require exactly one Stream ID for a vSID
tegra241_vintf_init_vsid() maps a guest vSID to a single physical Stream ID
taken from master->streams[0], and only warns when the device does not have
exactly one stream. A device with several streams gets only its first one
mapped, so a guest vSID invalidation cannot reach the others' ATC and IOTLB
entries; a device with none makes master->streams a ZERO_SIZE_PTR, read out
of bounds.
Reject the mapping with -EOPNOTSUPP if master->num_streams is not one. |
| In the Linux kernel, the following vulnerability has been resolved:
IB/isert: reject PDUs declaring more data than was received
isert_recv_done() hands each received PDU to the opcode handlers without
ever looking at wc->byte_len, the number of bytes the HCA actually placed
in the receive descriptor. The handlers then copy that many bytes - the
data-segment length the initiator declared in the BHS
(ntoh24(hdr->dlength), via the derived unsol_data_len / imm_data_len) -
out of the fixed-size descriptor:
isert_handle_iscsi_dataout():
sg_copy_from_buffer(sg_start, sg_nents, isert_get_data(rx_desc),
unsol_data_len);
isert_handle_scsi_cmd():
sg_copy_from_buffer(cmd->se_cmd.t_data_sg, sg_nents,
isert_get_data(rx_desc), imm_data_len);
Because the declared length is never checked against wc->byte_len, an
initiator can declare a data segment larger than the bytes it actually
sent (and larger than the descriptor) and cause an out-of-bounds read of
the receive buffer.
Nothing upstream of isert closes this door:
- __iscsit_check_dataout_hdr() bounds the inbound payload against
conn_ops->MaxXmitDataSegmentLength (MXDSL) - a transmit parameter,
used here for the inbound check.
- iscsi_set_connection_parameters() sets
ops->MaxXmitDataSegmentLength = ops->TargetRecvDataSegmentLength;
and TARGETRECVDATASEGMENTLENGTH is absent from the min()-clamp list in
iscsi_check_acceptor_state(), so the value the initiator declares is
adopted verbatim (type range 512..16777215). The initiator effectively
raises its own ceiling.
- isert never clamps the negotiated value to its own fixed receive
descriptor (ISER_RX_SIZE, 9216 bytes), so the target core's bound and
the descriptor size are unrelated.
The imm_data_len == data_len path is more than an over-read: it aliases
the receive descriptor via sg_set_buf() and passes it to the backend as
the data source for the SCSI WRITE, so an over-declared length causes heap
contents past the descriptor to be written through the backend to the
backing store. The backend is the victim of the oversized scatterlist
isert hands it, not the cause; no read-back of the written bytes was
demonstrated.
Trigger: after login completes (full feature phase), an initiator that has
declared a large TargetRecvDataSegmentLength and a FirstBurstLength that
permits unsolicited/immediate data sends a PDU whose declared data-segment
length exceeds what was received. With KASAN:
BUG: KASAN: slab-out-of-bounds in sg_copy_buffer+0x150/0x1c0
Read of size 4096 at addr ffff888109720800 by task kworker/1:0H/25
Workqueue: ib-comp-wq ib_cq_poll_work
Call Trace:
sg_copy_buffer+0x150/0x1c0
isert_recv_done+0xba6/0x2390
__ib_process_cq+0xe1/0x390
ib_cq_poll_work+0x46/0x150
isert_recv_done+0xba6 resolves to isert_handle_iscsi_dataout()
(ib_isert.c:1160), inlined through isert_rx_opcode().
Validate wc->byte_len against the framing in isert_recv_done() before the
PDU reaches any handler, and reinstate the connection if it is short.
Because the test compares without subtracting the header length, it also
rejects PDUs shorter than the iSER and iSCSI headers, which would otherwise
be parsed out of stale descriptor contents. The login handler rejects PDUs
shorter than ISER_HEADERS_LEN (commit 29e7b925ae6d ("IB/isert: Reject login
PDUs shorter than ISER_HEADERS_LEN")) but does not bound the declared
length either; that is fixed in the next patch. The data handlers had no
length check at all.
isert reads the data segment from a fixed offset: isert_get_data()
returns the iSER header plus ISER_HEADERS_LEN and makes no adjustment for
an AHS. The bytes the handlers touch are therefore exactly
[ISER_HEADERS_LEN, ISER_HEADERS_LEN + dlength), and comparing that sum
against wc->byte_len bounds precisely the region that is read. An AHS
term would only make the test stricter without bounding anything furth
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
nilfs2: prevent out-of-bounds read in super root block parsing
super-root inode metadata size is trusted before nilfs_read_inode_common().
Reject super-root inode sizes whose computed on-disk footprint exceeds the
filesystem block size. This prevents malformed filesystem images from
making nilfs_read_inode_common() read past the end of the super-root block.
[ryusuke: clarify the commit title] |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: virtio_bt: avoid OOB read of build info string
The virtbt_setup_zephyr() sends the Zephyr vendor command 0xfc08 (Read
Build Information) and hands the response to bt_dev_info() and
hci_set_fw_info() as a "%s" string starting at skb->data + 1, without
checking the length. A backend that answers with status only leaves that
pointer past the end of the received data, so the walk reads adjacent
slab memory until it meets a NUL. Those bytes reach the kernel log and
the firmware-info debugfs file.
To fix this, print the string with a bounded "%.*s" limited to
skb->len - 1. A short or unterminated response then prints as much as
arrived instead of failing setup.
This mirrors commit dd068ef04412 ("Bluetooth: bpa10x: avoid OOB read of
revision string in bpa10x_setup()"), which fixed the identical pattern. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/chrome: cros_ec_typec: Reject out-of-bounds PD cap count
cros_typec_register_partner_pdos() copies the partner PDOs from the EC
TYPEC_STATUS response into the fixed caps_desc.pdo[PDO_MAX_OBJECTS] array.
memcpy(caps_desc.pdo, resp->source_cap_pdos,
sizeof(u32) * resp->source_cap_count);
...
memcpy(caps_desc.pdo, resp->sink_cap_pdos,
sizeof(u32) * resp->sink_cap_count);
PDO_MAX_OBJECTS is 7. source_cap_count and sink_cap_count are u8 fields
from the EC. The only check is that they are not both zero. If either is
larger than 7, the memcpy writes past the end of the array on the stack.
A count of 255 overflows it by about 1 KB. The EC source arrays are only
seven entries wide. A larger count reads past them too.
The ChromeOS EC firmware caps these counts today, so a compliant setup
does not hit this. The kernel should still validate these values rather
than trust them.
Validate the counts in cros_typec_register_partner_pdos() next to the
memcpy. Skip the PDO registration if either count is above PDO_MAX_OBJECTS.
The rest of cros_typec_handle_status() still runs so events are handled
and cleared. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix WARNING in bpf_tracing_link_release
The trampoline could be corrupted by the blindly
'tr->flags = BPF_TRAMP_F_TAIL_CALL_CTX' in verifier.
1. A fexit attached to a tail_call_reachable prog. 'tr->flags' became
'BPF_TRAMP_F_CALL_ORIG | BPF_TRAMP_F_TAIL_CALL_CTX'. And, the
trampoline would poke the target prog's nop insn using jmp insn instead
of call insn.
2. Another fexit loaded with the same tail_call_reachable prog target.
'tr->flags' became 'BPF_TRAMP_F_TAIL_CALL_CTX'.
3. Close the first fexit link. Due to no BPF_TRAMP_F_CALL_ORIG in
'tr->flags', the trampoline will fail to restore the prog's nop insn
using call insn.
[ 3.410719] WARNING: kernel/bpf/syscall.c:3551 at bpf_tracing_link_release+0x53/0x60, CPU#1: test_progs/98
...
[ 3.428793] bpf_link_free+0x58/0x130
[ 3.429293] bpf_link_release+0x23/0x30
Fix the warning by updating 'tr->flags' with '|=' and lock. |
| In the Linux kernel, the following vulnerability has been resolved:
hfsplus: validate thread record before delete key rebuild
hfsplus_delete_cat() is called with str == NULL when the last open
reference to an unlinked HFS+ hardlink backing inode is closed. In that
case, the function finds the catalog thread by CNID and rebuilds the
catalog key from thread.nodeName.
That reconstruction path reads thread.nodeName.length directly from the
catalog B-tree into fd.search_key and then copies length * 2 bytes into
fd.search_key->cat.name.unicode. It does not first check that the found
record is a thread record or that its size matches the thread name.
A corrupted image can therefore provide an oversized thread name length
and make hfs_bnode_read() write past the catalog search-key allocation.
Read the CNID record through hfsplus_brec_read_cat(), which bounds the
record read to sizeof(hfsplus_cat_entry) and verifies that a thread
record's size exactly matches nodeName.length. Together, these checks
ensure an accepted thread name fits HFSPLUS_MAX_STRLEN. Reject non-thread
records before building the delete key from the validated thread name.
Share the thread-record-type helper between hfsplus_find_cat() and
hfsplus_delete_cat(). |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: uac: validate rate list length before storing
UAC1 and UAC2 configfs rate-list attributes parse a comma-separated
list of sampling rates and store each parsed value in fixed-size arrays.
The arrays have UAC_MAX_RATES entries, but the store paths do not check
that the input contains at most that many tokens before writing through
opts->name##s[i++].
Writing more than ten rates therefore writes past the end of the
p_srates[] or c_srates[] array in struct f_uac1_opts or struct
f_uac2_opts.
With CONFIG_UBSAN_BOUNDS enabled, writing an 11-entry rate list to the
UAC1 p_srate attribute reports:
UBSAN: array-index-out-of-bounds
drivers/usb/gadget/function/f_uac1.c:1669:1
index 10 is out of range for type 'int [10]'
__ubsan_handle_out_of_bounds.cold
f_uac1_opts_p_srate_store
configfs_write_iter
vfs_write
ksys_write
do_syscall_64
The same reproducer against the UAC2 p_srate attribute reports:
UBSAN: array-index-out-of-bounds
drivers/usb/gadget/function/f_uac2.c:2087:1
index 10 is out of range for type 'int [10]'
__ubsan_handle_out_of_bounds.cold
f_uac2_opts_p_srate_store
configfs_write_iter
vfs_write
ksys_write
do_syscall_64
Reject additional tokens once UAC_MAX_RATES entries have been parsed.
Also keep the original kstrdup() pointer for kfree(), because strsep()
advances the parsing cursor. Freeing the advanced cursor leaks the
original buffer on successful parses and can free an interior pointer on
some error paths. |
| A vulnerability in the RADIUS feature of Cisco Identity Services Engine (ISE) could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device.
This vulnerability is due to improper handling of certain RADIUS requests. An attacker could exploit this vulnerability by sending a crafted RADIUS request directly to an affected device. A successful exploit could allow the attacker to cause the ISE node to become unavailable. For single node deployments in that condition, endpoints that have not already authenticated would be unable to access the network until the node comes back up on its own. |
| An improper encoding or escaping of output vulnerability in SCGI in Synology DiskStation Manager (DSM) before 7.2.1-69057-12, 7.2.2-72806-9, 7.3.2-86009-4 and 7.4-90075 allows remote attackers to read or write arbitrary files and conduct denial-of-service attacks. |
| Grandstream GWN7660ELR before firmware version 1.0.27.6 contains an information disclosure vulnerability that allows unauthenticated remote attackers to obtain sensitive system information by querying the SNMP v2c service configured with the default community string 'public'. Attackers can query standard MIBs over the SNMP port to retrieve operating system and kernel version, running process names and command-line arguments, network interface configuration, routing table entries, ARP table mappings, active TCP connection details, and file system paths, enabling detailed reconnaissance of the device and adjacent network infrastructure. |
| An improper encoding or escaping of output vulnerability in Auth API in Synology DiskStation Manager (DSM) before 7.2.1-69057-12, 7.2.2-72806-9, 7.3.2-86009-4 and 7.4-90075 allows remote attackers to obtain non-sensitive information. |
