| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtl818x: Fix potential memory leaks in rtl8180_init_rx_ring()
In rtl8180_init_rx_ring(), memory is allocated for skb packets and DMA
allocations in a loop. When an allocation fails, the previously
successful allocations are not freed on exit.
Fix that by jumping to err_free_rings label on error, which calls
rtl8180_free_rx_ring() to free the allocations. Remove the free of
rx_ring in rtl8180_init_rx_ring() error path, and set the freed
priv->rx_buf entry to null, to avoid double free. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Fix potential out-of-bounds read in iommu_mmio_show
In iommu_mmio_write(), it validates the user-provided offset with the
check: `iommu->dbg_mmio_offset > iommu->mmio_phys_end - 4`.
This assumes a 4-byte access. However, the corresponding
show handler, iommu_mmio_show(), uses readq() to perform an 8-byte
(64-bit) read.
If a user provides an offset equal to `mmio_phys_end - 4`, the check
passes, and will lead to a 4-byte out-of-bounds read.
Fix this by adjusting the boundary check to use sizeof(u64), which
corresponds to the size of the readq() operation. |
| In the Linux kernel, the following vulnerability has been resolved:
fs: Protect reconfiguration of sb read-write from racing writes
The reconfigure / remount code takes a lot of effort to protect
filesystem's reconfiguration code from racing writes on remounting
read-only. However during remounting read-only filesystem to read-write
mode userspace writes can start immediately once we clear SB_RDONLY
flag. This is inconvenient for example for ext4 because we need to do
some writes to the filesystem (such as preparation of quota files)
before we can take userspace writes so we are clearing SB_RDONLY flag
before we are fully ready to accept userpace writes and syzbot has found
a way to exploit this [1]. Also as far as I'm reading the code
the filesystem remount code was protected from racing writes in the
legacy mount path by the mount's MNT_READONLY flag so this is relatively
new problem. It is actually fairly easy to protect remount read-write
from racing writes using sb->s_readonly_remount flag so let's just do
that instead of having to workaround these races in the filesystem code.
[1] https://lore.kernel.org/all/00000000000006a0df05f6667499@google.com/T/ |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qedi: Fix use after free bug in qedi_remove()
In qedi_probe() we call __qedi_probe() which initializes
&qedi->recovery_work with qedi_recovery_handler() and
&qedi->board_disable_work with qedi_board_disable_work().
When qedi_schedule_recovery_handler() is called, schedule_delayed_work()
will finally start the work.
In qedi_remove(), which is called to remove the driver, the following
sequence may be observed:
Fix this by finishing the work before cleanup in qedi_remove().
CPU0 CPU1
|qedi_recovery_handler
qedi_remove |
__qedi_remove |
iscsi_host_free |
scsi_host_put |
//free shost |
|iscsi_host_for_each_session
|//use qedi->shost
Cancel recovery_work and board_disable_work in __qedi_remove(). |
| In the Linux kernel, the following vulnerability has been resolved:
driver: soc: xilinx: use _safe loop iterator to avoid a use after free
The hash_for_each_possible() loop dereferences "eve_data" to get the
next item on the list. However the loop frees eve_data so it leads to
a use after free. Use hash_for_each_possible_safe() instead. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Prevent lpfc_debugfs_lockstat_write() buffer overflow
A static code analysis tool flagged the possibility of buffer overflow when
using copy_from_user() for a debugfs entry.
Currently, it is possible that copy_from_user() copies more bytes than what
would fit in the mybuf char array. Add a min() restriction check between
sizeof(mybuf) - 1 and nbytes passed from the userspace buffer to protect
against buffer overflow. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: rawnand: fsl_upm: Fix an off-by one test in fun_exec_op()
'op-cs' is copied in 'fun->mchip_number' which is used to access the
'mchip_offsets' and the 'rnb_gpio' arrays.
These arrays have NAND_MAX_CHIPS elements, so the index must be below this
limit.
Fix the sanity check in order to avoid the NAND_MAX_CHIPS value. This
would lead to out-of-bound accesses. |
| In the Linux kernel, the following vulnerability has been resolved:
can: isotp: check CAN address family in isotp_bind()
Add missing check to block non-AF_CAN binds.
Syzbot created some code which matched the right sockaddr struct size
but used AF_XDP (0x2C) instead of AF_CAN (0x1D) in the address family
field:
bind$xdp(r2, &(0x7f0000000540)={0x2c, 0x0, r4, 0x0, r2}, 0x10)
^^^^
This has no funtional impact but the userspace should be notified about
the wrong address family field content. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: fix potential memory leak in mlx5e_init_rep_rx
The memory pointed to by the priv->rx_res pointer is not freed in the error
path of mlx5e_init_rep_rx, which can lead to a memory leak. Fix by freeing
the memory in the error path, thereby making the error path identical to
mlx5e_cleanup_rep_rx(). |
| In the Linux kernel, the following vulnerability has been resolved:
blk-cgroup: dropping parent refcount after pd_free_fn() is done
Some cgroup policies will access parent pd through child pd even
after pd_offline_fn() is done. If pd_free_fn() for parent is called
before child, then UAF can be triggered. Hence it's better to guarantee
the order of pd_free_fn().
Currently refcount of parent blkg is dropped in __blkg_release(), which
is before pd_free_fn() is called in blkg_free_work_fn() while
blkg_free_work_fn() is called asynchronously.
This patch make sure pd_free_fn() called from removing cgroup is ordered
by delaying dropping parent refcount after calling pd_free_fn() for
child.
BTW, pd_free_fn() will also be called from blkcg_deactivate_policy()
from deleting device, and following patches will guarantee the order. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: rndis_host: Secure rndis_query check against int overflow
Variables off and len typed as uint32 in rndis_query function
are controlled by incoming RNDIS response message thus their
value may be manipulated. Setting off to a unexpectetly large
value will cause the sum with len and 8 to overflow and pass
the implemented validation step. Consequently the response
pointer will be referring to a location past the expected
buffer boundaries allowing information leakage e.g. via
RNDIS_OID_802_3_PERMANENT_ADDRESS OID. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: rockchip: Fix refcount leak in rockchip_pinctrl_parse_groups
of_find_node_by_phandle() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
kcm: Fix memory leak in error path of kcm_sendmsg()
syzbot reported a memory leak like below:
BUG: memory leak
unreferenced object 0xffff88810b088c00 (size 240):
comm "syz-executor186", pid 5012, jiffies 4294943306 (age 13.680s)
hex dump (first 32 bytes):
00 89 08 0b 81 88 ff ff 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff83e5d5ff>] __alloc_skb+0x1ef/0x230 net/core/skbuff.c:634
[<ffffffff84606e59>] alloc_skb include/linux/skbuff.h:1289 [inline]
[<ffffffff84606e59>] kcm_sendmsg+0x269/0x1050 net/kcm/kcmsock.c:815
[<ffffffff83e479c6>] sock_sendmsg_nosec net/socket.c:725 [inline]
[<ffffffff83e479c6>] sock_sendmsg+0x56/0xb0 net/socket.c:748
[<ffffffff83e47f55>] ____sys_sendmsg+0x365/0x470 net/socket.c:2494
[<ffffffff83e4c389>] ___sys_sendmsg+0xc9/0x130 net/socket.c:2548
[<ffffffff83e4c536>] __sys_sendmsg+0xa6/0x120 net/socket.c:2577
[<ffffffff84ad7bb8>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<ffffffff84ad7bb8>] do_syscall_64+0x38/0xb0 arch/x86/entry/common.c:80
[<ffffffff84c0008b>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
In kcm_sendmsg(), kcm_tx_msg(head)->last_skb is used as a cursor to append
newly allocated skbs to 'head'. If some bytes are copied, an error occurred,
and jumped to out_error label, 'last_skb' is left unmodified. A later
kcm_sendmsg() will use an obsoleted 'last_skb' reference, corrupting the
'head' frag_list and causing the leak.
This patch fixes this issue by properly updating the last allocated skb in
'last_skb'. |
| In the Linux kernel, the following vulnerability has been resolved:
media: i2c: tc358743: Fix use-after-free bugs caused by orphan timer in probe
The state->timer is a cyclic timer that schedules work_i2c_poll and
delayed_work_enable_hotplug, while rearming itself. Using timer_delete()
fails to guarantee the timer isn't still running when destroyed, similarly
cancel_delayed_work() cannot ensure delayed_work_enable_hotplug has
terminated if already executing. During probe failure after timer
initialization, these may continue running as orphans and reference the
already-freed tc358743_state object through tc358743_irq_poll_timer.
The following is the trace captured by KASAN.
BUG: KASAN: slab-use-after-free in __run_timer_base.part.0+0x7d7/0x8c0
Write of size 8 at addr ffff88800ded83c8 by task swapper/1/0
...
Call Trace:
<IRQ>
dump_stack_lvl+0x55/0x70
print_report+0xcf/0x610
? __pfx_sched_balance_find_src_group+0x10/0x10
? __run_timer_base.part.0+0x7d7/0x8c0
kasan_report+0xb8/0xf0
? __run_timer_base.part.0+0x7d7/0x8c0
__run_timer_base.part.0+0x7d7/0x8c0
? rcu_sched_clock_irq+0xb06/0x27d0
? __pfx___run_timer_base.part.0+0x10/0x10
? try_to_wake_up+0xb15/0x1960
? tmigr_update_events+0x280/0x740
? _raw_spin_lock_irq+0x80/0xe0
? __pfx__raw_spin_lock_irq+0x10/0x10
tmigr_handle_remote_up+0x603/0x7e0
? __pfx_tmigr_handle_remote_up+0x10/0x10
? sched_balance_trigger+0x98/0x9f0
? sched_tick+0x221/0x5a0
? _raw_spin_lock_irq+0x80/0xe0
? __pfx__raw_spin_lock_irq+0x10/0x10
? tick_nohz_handler+0x339/0x440
? __pfx_tmigr_handle_remote_up+0x10/0x10
__walk_groups.isra.0+0x42/0x150
tmigr_handle_remote+0x1f4/0x2e0
? __pfx_tmigr_handle_remote+0x10/0x10
? ktime_get+0x60/0x140
? lapic_next_event+0x11/0x20
? clockevents_program_event+0x1d4/0x2a0
? hrtimer_interrupt+0x322/0x780
handle_softirqs+0x16a/0x550
irq_exit_rcu+0xaf/0xe0
sysvec_apic_timer_interrupt+0x70/0x80
</IRQ>
...
Allocated by task 141:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x7f/0x90
__kmalloc_node_track_caller_noprof+0x198/0x430
devm_kmalloc+0x7b/0x1e0
tc358743_probe+0xb7/0x610 i2c_device_probe+0x51d/0x880
really_probe+0x1ca/0x5c0
__driver_probe_device+0x248/0x310
driver_probe_device+0x44/0x120
__device_attach_driver+0x174/0x220
bus_for_each_drv+0x100/0x190
__device_attach+0x206/0x370
bus_probe_device+0x123/0x170
device_add+0xd25/0x1470
i2c_new_client_device+0x7a0/0xcd0
do_one_initcall+0x89/0x300
do_init_module+0x29d/0x7f0
load_module+0x4f48/0x69e0
init_module_from_file+0xe4/0x150
idempotent_init_module+0x320/0x670
__x64_sys_finit_module+0xbd/0x120
do_syscall_64+0xac/0x280
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 141:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3a/0x60
__kasan_slab_free+0x3f/0x50
kfree+0x137/0x370
release_nodes+0xa4/0x100
devres_release_group+0x1b2/0x380
i2c_device_probe+0x694/0x880
really_probe+0x1ca/0x5c0
__driver_probe_device+0x248/0x310
driver_probe_device+0x44/0x120
__device_attach_driver+0x174/0x220
bus_for_each_drv+0x100/0x190
__device_attach+0x206/0x370
bus_probe_device+0x123/0x170
device_add+0xd25/0x1470
i2c_new_client_device+0x7a0/0xcd0
do_one_initcall+0x89/0x300
do_init_module+0x29d/0x7f0
load_module+0x4f48/0x69e0
init_module_from_file+0xe4/0x150
idempotent_init_module+0x320/0x670
__x64_sys_finit_module+0xbd/0x120
do_syscall_64+0xac/0x280
entry_SYSCALL_64_after_hwframe+0x77/0x7f
...
Replace timer_delete() with timer_delete_sync() and cancel_delayed_work()
with cancel_delayed_work_sync() to ensure proper termination of timer and
work items before resource cleanup.
This bug was initially identified through static analysis. For reproduction
and testing, I created a functional emulation of the tc358743 device via a
kernel module and introduced faults through the debugfs interface. |
| In the Linux kernel, the following vulnerability has been resolved:
net: nsh: Use correct mac_offset to unwind gso skb in nsh_gso_segment()
As the call trace shows, skb_panic was caused by wrong skb->mac_header
in nsh_gso_segment():
invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 3 PID: 2737 Comm: syz Not tainted 6.3.0-next-20230505 #1
RIP: 0010:skb_panic+0xda/0xe0
call Trace:
skb_push+0x91/0xa0
nsh_gso_segment+0x4f3/0x570
skb_mac_gso_segment+0x19e/0x270
__skb_gso_segment+0x1e8/0x3c0
validate_xmit_skb+0x452/0x890
validate_xmit_skb_list+0x99/0xd0
sch_direct_xmit+0x294/0x7c0
__dev_queue_xmit+0x16f0/0x1d70
packet_xmit+0x185/0x210
packet_snd+0xc15/0x1170
packet_sendmsg+0x7b/0xa0
sock_sendmsg+0x14f/0x160
The root cause is:
nsh_gso_segment() use skb->network_header - nhoff to reset mac_header
in skb_gso_error_unwind() if inner-layer protocol gso fails.
However, skb->network_header may be reset by inner-layer protocol
gso function e.g. mpls_gso_segment. skb->mac_header reset by the
inaccurate network_header will be larger than skb headroom.
nsh_gso_segment
nhoff = skb->network_header - skb->mac_header;
__skb_pull(skb,nsh_len)
skb_mac_gso_segment
mpls_gso_segment
skb_reset_network_header(skb);//skb->network_header+=nsh_len
return -EINVAL;
skb_gso_error_unwind
skb_push(skb, nsh_len);
skb->mac_header = skb->network_header - nhoff;
// skb->mac_header > skb->headroom, cause skb_push panic
Use correct mac_offset to restore mac_header and get rid of nhoff. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: pci_endpoint_test: Fix pci_endpoint_test_{copy,write,read}() panic
The dma_map_single() doesn't permit zero length mapping. It causes a follow
panic.
A panic was reported on arm64:
[ 60.137988] ------------[ cut here ]------------
[ 60.142630] kernel BUG at kernel/dma/swiotlb.c:624!
[ 60.147508] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 60.152992] Modules linked in: dw_hdmi_cec crct10dif_ce simple_bridge rcar_fdp1 vsp1 rcar_vin videobuf2_vmalloc rcar_csi2 v4l
2_mem2mem videobuf2_dma_contig videobuf2_memops pci_endpoint_test videobuf2_v4l2 videobuf2_common rcar_fcp v4l2_fwnode v4l2_asyn
c videodev mc gpio_bd9571mwv max9611 pwm_rcar ccree at24 authenc libdes phy_rcar_gen3_usb3 usb_dmac display_connector pwm_bl
[ 60.186252] CPU: 0 PID: 508 Comm: pcitest Not tainted 6.0.0-rc1rpci-dev+ #237
[ 60.193387] Hardware name: Renesas Salvator-X 2nd version board based on r8a77951 (DT)
[ 60.201302] pstate: 00000005 (nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 60.208263] pc : swiotlb_tbl_map_single+0x2c0/0x590
[ 60.213149] lr : swiotlb_map+0x88/0x1f0
[ 60.216982] sp : ffff80000a883bc0
[ 60.220292] x29: ffff80000a883bc0 x28: 0000000000000000 x27: 0000000000000000
[ 60.227430] x26: 0000000000000000 x25: ffff0004c0da20d0 x24: ffff80000a1f77c0
[ 60.234567] x23: 0000000000000002 x22: 0001000040000010 x21: 000000007a000000
[ 60.241703] x20: 0000000000200000 x19: 0000000000000000 x18: 0000000000000000
[ 60.248840] x17: 0000000000000000 x16: 0000000000000000 x15: ffff0006ff7b9180
[ 60.255977] x14: ffff0006ff7b9180 x13: 0000000000000000 x12: 0000000000000000
[ 60.263113] x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
[ 60.270249] x8 : 0001000000000010 x7 : ffff0004c6754b20 x6 : 0000000000000000
[ 60.277385] x5 : ffff0004c0da2090 x4 : 0000000000000000 x3 : 0000000000000001
[ 60.284521] x2 : 0000000040000000 x1 : 0000000000000000 x0 : 0000000040000010
[ 60.291658] Call trace:
[ 60.294100] swiotlb_tbl_map_single+0x2c0/0x590
[ 60.298629] swiotlb_map+0x88/0x1f0
[ 60.302115] dma_map_page_attrs+0x188/0x230
[ 60.306299] pci_endpoint_test_ioctl+0x5e4/0xd90 [pci_endpoint_test]
[ 60.312660] __arm64_sys_ioctl+0xa8/0xf0
[ 60.316583] invoke_syscall+0x44/0x108
[ 60.320334] el0_svc_common.constprop.0+0xcc/0xf0
[ 60.325038] do_el0_svc+0x2c/0xb8
[ 60.328351] el0_svc+0x2c/0x88
[ 60.331406] el0t_64_sync_handler+0xb8/0xc0
[ 60.335587] el0t_64_sync+0x18c/0x190
[ 60.339251] Code: 52800013 d2e00414 35fff45c d503201f (d4210000)
[ 60.345344] ---[ end trace 0000000000000000 ]---
To fix it, this patch adds a checking the payload length if it is zero. |
| In the Linux kernel, the following vulnerability has been resolved:
pcmcia: rsrc_nonstatic: Fix memory leak in nonstatic_release_resource_db()
When nonstatic_release_resource_db() frees all resources associated
with an PCMCIA socket, it forgets to free socket_data too, causing
a memory leak observable with kmemleak:
unreferenced object 0xc28d1000 (size 64):
comm "systemd-udevd", pid 297, jiffies 4294898478 (age 194.484s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 f0 85 0e c3 00 00 00 00 ................
00 00 00 00 0c 10 8d c2 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffda4245>] __kmem_cache_alloc_node+0x2d7/0x4a0
[<7e51f0c8>] kmalloc_trace+0x31/0xa4
[<d52b4ca0>] nonstatic_init+0x24/0x1a4 [pcmcia_rsrc]
[<a2f13e08>] pcmcia_register_socket+0x200/0x35c [pcmcia_core]
[<a728be1b>] yenta_probe+0x4d8/0xa70 [yenta_socket]
[<c48fac39>] pci_device_probe+0x99/0x194
[<84b7c690>] really_probe+0x181/0x45c
[<8060fe6e>] __driver_probe_device+0x75/0x1f4
[<b9b76f43>] driver_probe_device+0x28/0xac
[<648b766f>] __driver_attach+0xeb/0x1e4
[<6e9659eb>] bus_for_each_dev+0x61/0xb4
[<25a669f3>] driver_attach+0x1e/0x28
[<d8671d6b>] bus_add_driver+0x102/0x20c
[<df0d323c>] driver_register+0x5b/0x120
[<942cd8a4>] __pci_register_driver+0x44/0x4c
[<e536027e>] __UNIQUE_ID___addressable_cleanup_module188+0x1c/0xfffff000 [iTCO_vendor_support]
Fix this by freeing socket_data too.
Tested on a Acer Travelmate 4002WLMi by manually binding/unbinding
the yenta_cardbus driver (yenta_socket). |
| In the Linux kernel, the following vulnerability has been resolved:
s390/dcssblk: fix kernel crash with list_add corruption
Commit fb08a1908cb1 ("dax: simplify the dax_device <-> gendisk
association") introduced new logic for gendisk association, requiring
drivers to explicitly call dax_add_host() and dax_remove_host().
For dcssblk driver, some dax_remove_host() calls were missing, e.g. in
device remove path. The commit also broke error handling for out_dax case
in device add path, resulting in an extra put_device() w/o the previous
get_device() in that case.
This lead to stale xarray entries after device add / remove cycles. In the
case when a previously used struct gendisk pointer (xarray index) would be
used again, because blk_alloc_disk() happened to return such a pointer, the
xa_insert() in dax_add_host() would fail and go to out_dax, doing the extra
put_device() in the error path. In combination with an already flawed error
handling in dcssblk (device_register() cleanup), which needs to be
addressed in a separate patch, this resulted in a missing device_del() /
klist_del(), and eventually in the kernel crash with list_add corruption on
a subsequent device_add() / klist_add().
Fix this by adding the missing dax_remove_host() calls, and also move the
put_device() in the error path to restore the previous logic. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: sc16is7xx: setup GPIO controller later in probe
The GPIO controller component of the sc16is7xx driver is setup too
early, which can result in a race condition where another device tries
to utilise the GPIO lines before the sc16is7xx device has finished
initialising.
This issue manifests itself as an Oops when the GPIO lines are configured:
Unable to handle kernel read from unreadable memory at virtual address
...
pc : sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
lr : sc16is7xx_gpio_direction_output+0x4c/0x108 [sc16is7xx]
...
Call trace:
sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
gpiod_direction_output_raw_commit+0x64/0x318
gpiod_direction_output+0xb0/0x170
create_gpio_led+0xec/0x198
gpio_led_probe+0x16c/0x4f0
platform_drv_probe+0x5c/0xb0
really_probe+0xe8/0x448
driver_probe_device+0xe8/0x138
__device_attach_driver+0x94/0x118
bus_for_each_drv+0x8c/0xe0
__device_attach+0x100/0x1b8
device_initial_probe+0x28/0x38
bus_probe_device+0xa4/0xb0
deferred_probe_work_func+0x90/0xe0
process_one_work+0x1c4/0x480
worker_thread+0x54/0x430
kthread+0x138/0x150
ret_from_fork+0x10/0x1c
This patch moves the setup of the GPIO controller functions to later in the
probe function, ensuring the sc16is7xx device has already finished
initialising by the time other devices try to make use of the GPIO lines.
The error handling has also been reordered to reflect the new
initialisation order. |
| In the Linux kernel, the following vulnerability has been resolved:
inotify: Avoid reporting event with invalid wd
When inotify_freeing_mark() races with inotify_handle_inode_event() it
can happen that inotify_handle_inode_event() sees that i_mark->wd got
already reset to -1 and reports this value to userspace which can
confuse the inotify listener. Avoid the problem by validating that wd is
sensible (and pretend the mark got removed before the event got
generated otherwise). |
