| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
serial: amba-pl011: avoid SBSA UART accessing DMACR register
Chapter "B Generic UART" in "ARM Server Base System Architecture" [1]
documentation describes a generic UART interface. Such generic UART
does not support DMA. In current code, sbsa_uart_pops and
amba_pl011_pops share the same stop_rx operation, which will invoke
pl011_dma_rx_stop, leading to an access of the DMACR register. This
commit adds a using_rx_dma check in pl011_dma_rx_stop to avoid the
access to DMACR register for SBSA UARTs which does not support DMA.
When the kernel enables DMA engine with "CONFIG_DMA_ENGINE=y", Linux
SBSA PL011 driver will access PL011 DMACR register in some functions.
For most real SBSA Pl011 hardware implementations, the DMACR write
behaviour will be ignored. So these DMACR operations will not cause
obvious problems. But for some virtual SBSA PL011 hardware, like Xen
virtual SBSA PL011 (vpl011) device, the behaviour might be different.
Xen vpl011 emulation will inject a data abort to guest, when guest is
accessing an unimplemented UART register. As Xen VPL011 is SBSA
compatible, it will not implement DMACR register. So when Linux SBSA
PL011 driver access DMACR register, it will get an unhandled data abort
fault and the application will get a segmentation fault:
Unhandled fault at 0xffffffc00944d048
Mem abort info:
ESR = 0x96000000
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x00: ttbr address size fault
Data abort info:
ISV = 0, ISS = 0x00000000
CM = 0, WnR = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000020e2e000
[ffffffc00944d048] pgd=100000003ffff803, p4d=100000003ffff803, pud=100000003ffff803, pmd=100000003fffa803, pte=006800009c090f13
Internal error: ttbr address size fault: 96000000 [#1] PREEMPT SMP
...
Call trace:
pl011_stop_rx+0x70/0x80
tty_port_shutdown+0x7c/0xb4
tty_port_close+0x60/0xcc
uart_close+0x34/0x8c
tty_release+0x144/0x4c0
__fput+0x78/0x220
____fput+0x1c/0x30
task_work_run+0x88/0xc0
do_notify_resume+0x8d0/0x123c
el0_svc+0xa8/0xc0
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x1a0/0x1a4
Code: b9000083 b901f001 794038a0 8b000042 (b9000041)
---[ end trace 83dd93df15c3216f ]---
note: bootlogd[132] exited with preempt_count 1
/etc/rcS.d/S07bootlogd: line 47: 132 Segmentation fault start-stop-daemon
This has been discussed in the Xen community, and we think it should fix
this in Linux. See [2] for more information.
[1] https://developer.arm.com/documentation/den0094/c/?lang=en
[2] https://lists.xenproject.org/archives/html/xen-devel/2022-11/msg00543.html |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rsi: Fix memory leak in rsi_coex_attach()
The coex_cb needs to be freed when rsi_create_kthread() failed in
rsi_coex_attach(). |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Move representor neigh cleanup to profile cleanup_tx
For IP tunnel encapsulation in ECMP (Equal-Cost Multipath) mode, as
the flow is duplicated to the peer eswitch, the related neighbour
information on the peer uplink representor is created as well.
In the cited commit, eswitch devcom unpair is moved to uplink unload
API, specifically the profile->cleanup_tx. If there is a encap rule
offloaded in ECMP mode, when one eswitch does unpair (because of
unloading the driver, for instance), and the peer rule from the peer
eswitch is going to be deleted, the use-after-free error is triggered
while accessing neigh info, as it is already cleaned up in uplink's
profile->disable, which is before its profile->cleanup_tx.
To fix this issue, move the neigh cleanup to profile's cleanup_tx
callback, and after mlx5e_cleanup_uplink_rep_tx is called. The neigh
init is moved to init_tx for symmeter.
[ 2453.376299] BUG: KASAN: slab-use-after-free in mlx5e_rep_neigh_entry_release+0x109/0x3a0 [mlx5_core]
[ 2453.379125] Read of size 4 at addr ffff888127af9008 by task modprobe/2496
[ 2453.381542] CPU: 7 PID: 2496 Comm: modprobe Tainted: G B 6.4.0-rc7+ #15
[ 2453.383386] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[ 2453.384335] Call Trace:
[ 2453.384625] <TASK>
[ 2453.384891] dump_stack_lvl+0x33/0x50
[ 2453.385285] print_report+0xc2/0x610
[ 2453.385667] ? __virt_addr_valid+0xb1/0x130
[ 2453.386091] ? mlx5e_rep_neigh_entry_release+0x109/0x3a0 [mlx5_core]
[ 2453.386757] kasan_report+0xae/0xe0
[ 2453.387123] ? mlx5e_rep_neigh_entry_release+0x109/0x3a0 [mlx5_core]
[ 2453.387798] mlx5e_rep_neigh_entry_release+0x109/0x3a0 [mlx5_core]
[ 2453.388465] mlx5e_rep_encap_entry_detach+0xa6/0xe0 [mlx5_core]
[ 2453.389111] mlx5e_encap_dealloc+0xa7/0x100 [mlx5_core]
[ 2453.389706] mlx5e_tc_tun_encap_dests_unset+0x61/0xb0 [mlx5_core]
[ 2453.390361] mlx5_free_flow_attr_actions+0x11e/0x340 [mlx5_core]
[ 2453.391015] ? complete_all+0x43/0xd0
[ 2453.391398] ? free_flow_post_acts+0x38/0x120 [mlx5_core]
[ 2453.392004] mlx5e_tc_del_fdb_flow+0x4ae/0x690 [mlx5_core]
[ 2453.392618] mlx5e_tc_del_fdb_peers_flow+0x308/0x370 [mlx5_core]
[ 2453.393276] mlx5e_tc_clean_fdb_peer_flows+0xf5/0x140 [mlx5_core]
[ 2453.393925] mlx5_esw_offloads_unpair+0x86/0x540 [mlx5_core]
[ 2453.394546] ? mlx5_esw_offloads_set_ns_peer.isra.0+0x180/0x180 [mlx5_core]
[ 2453.395268] ? down_write+0xaa/0x100
[ 2453.395652] mlx5_esw_offloads_devcom_event+0x203/0x530 [mlx5_core]
[ 2453.396317] mlx5_devcom_send_event+0xbb/0x190 [mlx5_core]
[ 2453.396917] mlx5_esw_offloads_devcom_cleanup+0xb0/0xd0 [mlx5_core]
[ 2453.397582] mlx5e_tc_esw_cleanup+0x42/0x120 [mlx5_core]
[ 2453.398182] mlx5e_rep_tc_cleanup+0x15/0x30 [mlx5_core]
[ 2453.398768] mlx5e_cleanup_rep_tx+0x6c/0x80 [mlx5_core]
[ 2453.399367] mlx5e_detach_netdev+0xee/0x120 [mlx5_core]
[ 2453.399957] mlx5e_netdev_change_profile+0x84/0x170 [mlx5_core]
[ 2453.400598] mlx5e_vport_rep_unload+0xe0/0xf0 [mlx5_core]
[ 2453.403781] mlx5_eswitch_unregister_vport_reps+0x15e/0x190 [mlx5_core]
[ 2453.404479] ? mlx5_eswitch_register_vport_reps+0x200/0x200 [mlx5_core]
[ 2453.405170] ? up_write+0x39/0x60
[ 2453.405529] ? kernfs_remove_by_name_ns+0xb7/0xe0
[ 2453.405985] auxiliary_bus_remove+0x2e/0x40
[ 2453.406405] device_release_driver_internal+0x243/0x2d0
[ 2453.406900] ? kobject_put+0x42/0x2d0
[ 2453.407284] bus_remove_device+0x128/0x1d0
[ 2453.407687] device_del+0x240/0x550
[ 2453.408053] ? waiting_for_supplier_show+0xe0/0xe0
[ 2453.408511] ? kobject_put+0xfa/0x2d0
[ 2453.408889] ? __kmem_cache_free+0x14d/0x280
[ 2453.409310] mlx5_rescan_drivers_locked.part.0+0xcd/0x2b0 [mlx5_core]
[ 2453.409973] mlx5_unregister_device+0x40/0x50 [mlx5_core]
[ 2453.410561] mlx5_uninit_one+0x3d/0x110 [mlx5_core]
[ 2453.411111] remove_one+0x89/0x130 [mlx5_core]
[ 24
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix monitor mode bringup crash
When the interface is brought up in monitor mode, it leads
to NULL pointer dereference crash. This crash happens when
the packet type is extracted for a SKB. This extraction
which is present in the received msdu delivery path,is
not needed for the monitor ring packets since they are
all RAW packets. Hence appending the flags with
"RX_FLAG_ONLY_MONITOR" to skip that extraction.
Observed calltrace:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000064
Mem abort info:
ESR = 0x0000000096000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x04: level 0 translation fault
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=0000000048517000
[0000000000000064] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
Modules linked in: ath11k_pci ath11k qmi_helpers
CPU: 2 PID: 1781 Comm: napi/-271 Not tainted
6.1.0-rc5-wt-ath-656295-gef907406320c-dirty #6
Hardware name: Qualcomm Technologies, Inc. IPQ8074/AP-HK10-C2 (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : ath11k_hw_qcn9074_rx_desc_get_decap_type+0x34/0x60 [ath11k]
lr : ath11k_hw_qcn9074_rx_desc_get_decap_type+0x5c/0x60 [ath11k]
sp : ffff80000ef5bb10
x29: ffff80000ef5bb10 x28: 0000000000000000 x27: ffff000007baafa0
x26: ffff000014a91ed0 x25: 0000000000000000 x24: 0000000000000000
x23: ffff800002b77378 x22: ffff000014a91ec0 x21: ffff000006c8d600
x20: 0000000000000000 x19: ffff800002b77740 x18: 0000000000000006
x17: 736564203634343a x16: 656e694c20657079 x15: 0000000000000143
x14: 00000000ffffffea x13: ffff80000ef5b8b8 x12: ffff80000ef5b8c8
x11: ffff80000a591d30 x10: ffff80000a579d40 x9 : c0000000ffffefff
x8 : 0000000000000003 x7 : 0000000000017fe8 x6 : ffff80000a579ce8
x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000
x2 : 3a35ec12ed7f8900 x1 : 0000000000000000 x0 : 0000000000000052
Call trace:
ath11k_hw_qcn9074_rx_desc_get_decap_type+0x34/0x60 [ath11k]
ath11k_dp_rx_deliver_msdu.isra.42+0xa4/0x3d0 [ath11k]
ath11k_dp_rx_mon_deliver.isra.43+0x2f8/0x458 [ath11k]
ath11k_dp_rx_process_mon_rings+0x310/0x4c0 [ath11k]
ath11k_dp_service_srng+0x234/0x338 [ath11k]
ath11k_pcic_ext_grp_napi_poll+0x30/0xb8 [ath11k]
__napi_poll+0x5c/0x190
napi_threaded_poll+0xf0/0x118
kthread+0xf4/0x110
ret_from_fork+0x10/0x20
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: sg: Do not sleep in atomic context
sg_finish_rem_req() calls blk_rq_unmap_user(). The latter function may
sleep. Hence, call sg_finish_rem_req() with interrupts enabled instead
of disabled. |
| In the Linux kernel, the following vulnerability has been resolved:
media: rcar_fdp1: Fix refcount leak in probe and remove function
rcar_fcp_get() take reference, which should be balanced with
rcar_fcp_put(). Add missing rcar_fcp_put() in fdp1_remove and
the error paths of fdp1_probe() to fix this.
[hverkuil: resolve merge conflict, remove() is now void] |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-fc: move lsop put work to nvmet_fc_ls_req_op
It’s possible for more than one async command to be in flight from
__nvmet_fc_send_ls_req. For each command, a tgtport reference is taken.
In the current code, only one put work item is queued at a time, which
results in a leaked reference.
To fix this, move the work item to the nvmet_fc_ls_req_op struct, which
already tracks all resources related to the command. |
| In the Linux kernel, the following vulnerability has been resolved:
rcu: dump vmalloc memory info safely
Currently, for double invoke call_rcu(), will dump rcu_head objects memory
info, if the objects is not allocated from the slab allocator, the
vmalloc_dump_obj() will be invoke and the vmap_area_lock spinlock need to
be held, since the call_rcu() can be invoked in interrupt context,
therefore, there is a possibility of spinlock deadlock scenarios.
And in Preempt-RT kernel, the rcutorture test also trigger the following
lockdep warning:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 1, name: swapper/0
preempt_count: 1, expected: 0
RCU nest depth: 1, expected: 1
3 locks held by swapper/0/1:
#0: ffffffffb534ee80 (fullstop_mutex){+.+.}-{4:4}, at: torture_init_begin+0x24/0xa0
#1: ffffffffb5307940 (rcu_read_lock){....}-{1:3}, at: rcu_torture_init+0x1ec7/0x2370
#2: ffffffffb536af40 (vmap_area_lock){+.+.}-{3:3}, at: find_vmap_area+0x1f/0x70
irq event stamp: 565512
hardirqs last enabled at (565511): [<ffffffffb379b138>] __call_rcu_common+0x218/0x940
hardirqs last disabled at (565512): [<ffffffffb5804262>] rcu_torture_init+0x20b2/0x2370
softirqs last enabled at (399112): [<ffffffffb36b2586>] __local_bh_enable_ip+0x126/0x170
softirqs last disabled at (399106): [<ffffffffb43fef59>] inet_register_protosw+0x9/0x1d0
Preemption disabled at:
[<ffffffffb58040c3>] rcu_torture_init+0x1f13/0x2370
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 6.5.0-rc4-rt2-yocto-preempt-rt+ #15
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x68/0xb0
dump_stack+0x14/0x20
__might_resched+0x1aa/0x280
? __pfx_rcu_torture_err_cb+0x10/0x10
rt_spin_lock+0x53/0x130
? find_vmap_area+0x1f/0x70
find_vmap_area+0x1f/0x70
vmalloc_dump_obj+0x20/0x60
mem_dump_obj+0x22/0x90
__call_rcu_common+0x5bf/0x940
? debug_smp_processor_id+0x1b/0x30
call_rcu_hurry+0x14/0x20
rcu_torture_init+0x1f82/0x2370
? __pfx_rcu_torture_leak_cb+0x10/0x10
? __pfx_rcu_torture_leak_cb+0x10/0x10
? __pfx_rcu_torture_init+0x10/0x10
do_one_initcall+0x6c/0x300
? debug_smp_processor_id+0x1b/0x30
kernel_init_freeable+0x2b9/0x540
? __pfx_kernel_init+0x10/0x10
kernel_init+0x1f/0x150
ret_from_fork+0x40/0x50
? __pfx_kernel_init+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
The previous patch fixes this by using the deadlock-safe best-effort
version of find_vm_area. However, in case of failure print the fact that
the pointer was a vmalloc pointer so that we print at least something. |
| In the Linux kernel, the following vulnerability has been resolved:
cpufreq/longhaul: handle NULL policy in longhaul_exit
longhaul_exit() was calling cpufreq_cpu_get(0) without checking
for a NULL policy pointer. On some systems, this could lead to a
NULL dereference and a kernel warning or panic.
This patch adds a check using unlikely() and returns early if the
policy is NULL.
Bugzilla: #219962 |
| In the Linux kernel, the following vulnerability has been resolved:
gve: Implement settime64 with -EOPNOTSUPP
ptp_clock_settime() assumes every ptp_clock has implemented settime64().
Stub it with -EOPNOTSUPP to prevent a NULL dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix buffer validation by including null terminator size in EA length
The smb2_set_ea function, which handles Extended Attributes (EA),
was performing buffer validation checks that incorrectly omitted the size
of the null terminating character (+1 byte) for EA Name.
This patch fixes the issue by explicitly adding '+ 1' to EaNameLength where
the null terminator is expected to be present in the buffer, ensuring
the validation accurately reflects the total required buffer size. |
| In the Linux kernel, the following vulnerability has been resolved:
fscrypt: fix left shift underflow when inode->i_blkbits > PAGE_SHIFT
When simulating an nvme device on qemu with both logical_block_size and
physical_block_size set to 8 KiB, an error trace appears during
partition table reading at boot time. The issue is caused by
inode->i_blkbits being larger than PAGE_SHIFT, which leads to a left
shift of -1 and triggering a UBSAN warning.
[ 2.697306] ------------[ cut here ]------------
[ 2.697309] UBSAN: shift-out-of-bounds in fs/crypto/inline_crypt.c:336:37
[ 2.697311] shift exponent -1 is negative
[ 2.697315] CPU: 3 UID: 0 PID: 274 Comm: (udev-worker) Not tainted 6.18.0-rc2+ #34 PREEMPT(voluntary)
[ 2.697317] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
[ 2.697320] Call Trace:
[ 2.697324] <TASK>
[ 2.697325] dump_stack_lvl+0x76/0xa0
[ 2.697340] dump_stack+0x10/0x20
[ 2.697342] __ubsan_handle_shift_out_of_bounds+0x1e3/0x390
[ 2.697351] bh_get_inode_and_lblk_num.cold+0x12/0x94
[ 2.697359] fscrypt_set_bio_crypt_ctx_bh+0x44/0x90
[ 2.697365] submit_bh_wbc+0xb6/0x190
[ 2.697370] block_read_full_folio+0x194/0x270
[ 2.697371] ? __pfx_blkdev_get_block+0x10/0x10
[ 2.697375] ? __pfx_blkdev_read_folio+0x10/0x10
[ 2.697377] blkdev_read_folio+0x18/0x30
[ 2.697379] filemap_read_folio+0x40/0xe0
[ 2.697382] filemap_get_pages+0x5ef/0x7a0
[ 2.697385] ? mmap_region+0x63/0xd0
[ 2.697389] filemap_read+0x11d/0x520
[ 2.697392] blkdev_read_iter+0x7c/0x180
[ 2.697393] vfs_read+0x261/0x390
[ 2.697397] ksys_read+0x71/0xf0
[ 2.697398] __x64_sys_read+0x19/0x30
[ 2.697399] x64_sys_call+0x1e88/0x26a0
[ 2.697405] do_syscall_64+0x80/0x670
[ 2.697410] ? __x64_sys_newfstat+0x15/0x20
[ 2.697414] ? x64_sys_call+0x204a/0x26a0
[ 2.697415] ? do_syscall_64+0xb8/0x670
[ 2.697417] ? irqentry_exit_to_user_mode+0x2e/0x2a0
[ 2.697420] ? irqentry_exit+0x43/0x50
[ 2.697421] ? exc_page_fault+0x90/0x1b0
[ 2.697422] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 2.697425] RIP: 0033:0x75054cba4a06
[ 2.697426] Code: 5d e8 41 8b 93 08 03 00 00 59 5e 48 83 f8 fc 75 19 83 e2 39 83 fa 08 75 11 e8 26 ff ff ff 66 0f 1f 44 00 00 48 8b 45 10 0f 05 <48> 8b 5d f8 c9 c3 0f 1f 40 00 f3 0f 1e fa 55 48 89 e5 48 83 ec 08
[ 2.697427] RSP: 002b:00007fff973723a0 EFLAGS: 00000202 ORIG_RAX: 0000000000000000
[ 2.697430] RAX: ffffffffffffffda RBX: 00005ea9a2c02760 RCX: 000075054cba4a06
[ 2.697432] RDX: 0000000000002000 RSI: 000075054c190000 RDI: 000000000000001b
[ 2.697433] RBP: 00007fff973723c0 R08: 0000000000000000 R09: 0000000000000000
[ 2.697434] R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000000
[ 2.697434] R13: 00005ea9a2c027c0 R14: 00005ea9a2be5608 R15: 00005ea9a2be55f0
[ 2.697436] </TASK>
[ 2.697436] ---[ end trace ]---
This situation can happen for block devices because when
CONFIG_TRANSPARENT_HUGEPAGE is enabled, the maximum logical_block_size
is 64 KiB. set_init_blocksize() then sets the block device
inode->i_blkbits to 13, which is within this limit.
File I/O does not trigger this problem because for filesystems that do
not support the FS_LBS feature, sb_set_blocksize() prevents
sb->s_blocksize_bits from being larger than PAGE_SHIFT. During inode
allocation, alloc_inode()->inode_init_always() assigns inode->i_blkbits
from sb->s_blocksize_bits. Currently, only xfs_fs_type has the FS_LBS
flag, and since xfs I/O paths do not reach submit_bh_wbc(), it does not
hit the left-shift underflow issue.
[EB: use folio_pos() and consolidate the two shifts by i_blkbits] |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: core: fix unbalanced of node refcount in regulator_dev_lookup()
I got the the following report:
OF: ERROR: memory leak, expected refcount 1 instead of 2,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /i2c/pmic@62/regulators/exten
In of_get_regulator(), the node is returned from of_parse_phandle()
with refcount incremented, after using it, of_node_put() need be called. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/mm: Fix SMP ordering in switch_mm_irqs_off()
Stephen noted that it is possible to not have an smp_mb() between
the loaded_mm store and the tlb_gen load in switch_mm(), meaning the
ordering against flush_tlb_mm_range() goes out the window, and it
becomes possible for switch_mm() to not observe a recent tlb_gen
update and fail to flush the TLBs.
[ dhansen: merge conflict fixed by Ingo ] |
| In the Linux kernel, the following vulnerability has been resolved:
accel/qaic: Fix bootlog initialization ordering
As soon as we queue MHI buffers to receive the bootlog from the device,
we could be receiving data. Therefore all the resources needed to
process that data need to be setup prior to queuing the buffers.
We currently initialize some of the resources after queuing the buffers
which creates a race between the probe() and any data that comes back
from the device. If the uninitialized resources are accessed, we could
see page faults.
Fix the init ordering to close the race. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Fix debug checking for np-guests using huge mappings
When running with transparent huge pages and CONFIG_NVHE_EL2_DEBUG then
the debug checking in assert_host_shared_guest() fails on the launch of an
np-guest. This WARN_ON() causes a panic and generates the stack below.
In __pkvm_host_relax_perms_guest() the debug checking assumes the mapping
is a single page but it may be a block map. Update the checking so that
the size is not checked and just assumes the correct size.
While we're here make the same fix in __pkvm_host_mkyoung_guest().
Info: # lkvm run -k /share/arch/arm64/boot/Image -m 704 -c 8 --name guest-128
Info: Removed ghost socket file "/.lkvm//guest-128.sock".
[ 1406.521757] kvm [141]: nVHE hyp BUG at: arch/arm64/kvm/hyp/nvhe/mem_protect.c:1088!
[ 1406.521804] kvm [141]: nVHE call trace:
[ 1406.521828] kvm [141]: [<ffff8000811676b4>] __kvm_nvhe_hyp_panic+0xb4/0xe8
[ 1406.521946] kvm [141]: [<ffff80008116d12c>] __kvm_nvhe_assert_host_shared_guest+0xb0/0x10c
[ 1406.522049] kvm [141]: [<ffff80008116f068>] __kvm_nvhe___pkvm_host_relax_perms_guest+0x48/0x104
[ 1406.522157] kvm [141]: [<ffff800081169df8>] __kvm_nvhe_handle___pkvm_host_relax_perms_guest+0x64/0x7c
[ 1406.522250] kvm [141]: [<ffff800081169f0c>] __kvm_nvhe_handle_trap+0x8c/0x1a8
[ 1406.522333] kvm [141]: [<ffff8000811680fc>] __kvm_nvhe___skip_pauth_save+0x4/0x4
[ 1406.522454] kvm [141]: ---[ end nVHE call trace ]---
[ 1406.522477] kvm [141]: Hyp Offset: 0xfffece8013600000
[ 1406.522554] Kernel panic - not syncing: HYP panic:
[ 1406.522554] PS:834003c9 PC:0000b1806db6d170 ESR:00000000f2000800
[ 1406.522554] FAR:ffff8000804be420 HPFAR:0000000000804be0 PAR:0000000000000000
[ 1406.522554] VCPU:0000000000000000
[ 1406.523337] CPU: 3 UID: 0 PID: 141 Comm: kvm-vcpu-0 Not tainted 6.16.0-rc7 #97 PREEMPT
[ 1406.523485] Hardware name: FVP Base RevC (DT)
[ 1406.523566] Call trace:
[ 1406.523629] show_stack+0x18/0x24 (C)
[ 1406.523753] dump_stack_lvl+0xd4/0x108
[ 1406.523899] dump_stack+0x18/0x24
[ 1406.524040] panic+0x3d8/0x448
[ 1406.524184] nvhe_hyp_panic_handler+0x10c/0x23c
[ 1406.524325] kvm_handle_guest_abort+0x68c/0x109c
[ 1406.524500] handle_exit+0x60/0x17c
[ 1406.524630] kvm_arch_vcpu_ioctl_run+0x2e0/0x8c0
[ 1406.524794] kvm_vcpu_ioctl+0x1a8/0x9cc
[ 1406.524919] __arm64_sys_ioctl+0xac/0x104
[ 1406.525067] invoke_syscall+0x48/0x10c
[ 1406.525189] el0_svc_common.constprop.0+0x40/0xe0
[ 1406.525322] do_el0_svc+0x1c/0x28
[ 1406.525441] el0_svc+0x38/0x120
[ 1406.525588] el0t_64_sync_handler+0x10c/0x138
[ 1406.525750] el0t_64_sync+0x1ac/0x1b0
[ 1406.525876] SMP: stopping secondary CPUs
[ 1406.525965] Kernel Offset: disabled
[ 1406.526032] CPU features: 0x0000,00000080,8e134ca1,9446773f
[ 1406.526130] Memory Limit: none
[ 1406.959099] ---[ end Kernel panic - not syncing: HYP panic:
[ 1406.959099] PS:834003c9 PC:0000b1806db6d170 ESR:00000000f2000800
[ 1406.959099] FAR:ffff8000804be420 HPFAR:0000000000804be0 PAR:0000000000000000
[ 1406.959099] VCPU:0000000000000000 ] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd: Fix an out of bounds error in BIOS parser
The array is hardcoded to 8 in atomfirmware.h, but firmware provides
a bigger one sometimes. Deferencing the larger array causes an out
of bounds error.
commit 4fc1ba4aa589 ("drm/amd/display: fix array index out of bound error
in bios parser") fixed some of this, but there are two other cases
not covered by it. Fix those as well. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: avoid suspicious RCU usage for synced VLAN-aware MAC addresses
When using the felix driver (the only one which supports UC filtering
and MC filtering) as a DSA master for a random other DSA switch, one can
see the following stack trace when the downstream switch ports join a
VLAN-aware bridge:
=============================
WARNING: suspicious RCU usage
-----------------------------
net/8021q/vlan_core.c:238 suspicious rcu_dereference_protected() usage!
stack backtrace:
Workqueue: dsa_ordered dsa_slave_switchdev_event_work
Call trace:
lockdep_rcu_suspicious+0x170/0x210
vlan_for_each+0x8c/0x188
dsa_slave_sync_uc+0x128/0x178
__hw_addr_sync_dev+0x138/0x158
dsa_slave_set_rx_mode+0x58/0x70
__dev_set_rx_mode+0x88/0xa8
dev_uc_add+0x74/0xa0
dsa_port_bridge_host_fdb_add+0xec/0x180
dsa_slave_switchdev_event_work+0x7c/0x1c8
process_one_work+0x290/0x568
What it's saying is that vlan_for_each() expects rtnl_lock() context and
it's not getting it, when it's called from the DSA master's ndo_set_rx_mode().
The caller of that - dsa_slave_set_rx_mode() - is the slave DSA
interface's dsa_port_bridge_host_fdb_add() which comes from the deferred
dsa_slave_switchdev_event_work().
We went to great lengths to avoid the rtnl_lock() context in that call
path in commit 0faf890fc519 ("net: dsa: drop rtnl_lock from
dsa_slave_switchdev_event_work"), and calling rtnl_lock() is simply not
an option due to the possibility of deadlocking when calling
dsa_flush_workqueue() from the call paths that do hold rtnl_lock() -
basically all of them.
So, when the DSA master calls vlan_for_each() from its ndo_set_rx_mode(),
the state of the 8021q driver on this device is really not protected
from concurrent access by anything.
Looking at net/8021q/, I don't think that vlan_info->vid_list was
particularly designed with RCU traversal in mind, so introducing an RCU
read-side form of vlan_for_each() - vlan_for_each_rcu() - won't be so
easy, and it also wouldn't be exactly what we need anyway.
In general I believe that the solution isn't in net/8021q/ anyway;
vlan_for_each() is not cut out for this task. DSA doesn't need rtnl_lock()
to be held per se - since it's not a netdev state change that we're
blocking, but rather, just concurrent additions/removals to a VLAN list.
We don't even need sleepable context - the callback of vlan_for_each()
just schedules deferred work.
The proposed escape is to remove the dependency on vlan_for_each() and
to open-code a non-sleepable, rtnl-free alternative to that, based on
copies of the VLAN list modified from .ndo_vlan_rx_add_vid() and
.ndo_vlan_rx_kill_vid(). |
| In the Linux kernel, the following vulnerability has been resolved:
ice: ice_adapter: release xa entry on adapter allocation failure
When ice_adapter_new() fails, the reserved XArray entry created by
xa_insert() is not released. This causes subsequent insertions at
the same index to return -EBUSY, potentially leading to
NULL pointer dereferences.
Reorder the operations as suggested by Przemek Kitszel:
1. Check if adapter already exists (xa_load)
2. Reserve the XArray slot (xa_reserve)
3. Allocate the adapter (ice_adapter_new)
4. Store the adapter (xa_store) |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: realtek: fix out-of-bounds access
The probe function sets priv->chip_data to (void *)priv + sizeof(*priv)
with the expectation that priv has enough trailing space.
However, only realtek-smi actually allocated this chip_data space.
Do likewise in realtek-mdio to fix out-of-bounds accesses.
These accesses likely went unnoticed so far, because of an (unused)
buf[4096] member in struct realtek_priv, which caused kmalloc to
round up the allocated buffer to a big enough size, so nothing of
value was overwritten. With a different allocator (like in the barebox
bootloader port of the driver) or with KASAN, the memory corruption
becomes quickly apparent. |
