| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/mxsfb: Disable overlay plane in mxsfb_plane_overlay_atomic_disable()
When disabling overlay plane in mxsfb_plane_overlay_atomic_update(),
overlay plane's framebuffer pointer is NULL. So, dereferencing it would
cause a kernel Oops(NULL pointer dereferencing). Fix the issue by
disabling overlay plane in mxsfb_plane_overlay_atomic_disable() instead. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: fix crash while sending Action Frames in standalone AP Mode
Currently, whenever there is a need to transmit an Action frame,
the brcmfmac driver always uses the P2P vif to send the "actframe" IOVAR to
firmware. The P2P interfaces were available when wpa_supplicant is managing
the wlan interface.
However, the P2P interfaces are not created/initialized when only hostapd
is managing the wlan interface. And if hostapd receives an ANQP Query REQ
Action frame even from an un-associated STA, the brcmfmac driver tries
to use an uninitialized P2P vif pointer for sending the IOVAR to firmware.
This NULL pointer dereferencing triggers a driver crash.
[ 1417.074538] Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000000
[...]
[ 1417.075188] Hardware name: Raspberry Pi 4 Model B Rev 1.5 (DT)
[...]
[ 1417.075653] Call trace:
[ 1417.075662] brcmf_p2p_send_action_frame+0x23c/0xc58 [brcmfmac]
[ 1417.075738] brcmf_cfg80211_mgmt_tx+0x304/0x5c0 [brcmfmac]
[ 1417.075810] cfg80211_mlme_mgmt_tx+0x1b0/0x428 [cfg80211]
[ 1417.076067] nl80211_tx_mgmt+0x238/0x388 [cfg80211]
[ 1417.076281] genl_family_rcv_msg_doit+0xe0/0x158
[ 1417.076302] genl_rcv_msg+0x220/0x2a0
[ 1417.076317] netlink_rcv_skb+0x68/0x140
[ 1417.076330] genl_rcv+0x40/0x60
[ 1417.076343] netlink_unicast+0x330/0x3b8
[ 1417.076357] netlink_sendmsg+0x19c/0x3f8
[ 1417.076370] __sock_sendmsg+0x64/0xc0
[ 1417.076391] ____sys_sendmsg+0x268/0x2a0
[ 1417.076408] ___sys_sendmsg+0xb8/0x118
[ 1417.076427] __sys_sendmsg+0x90/0xf8
[ 1417.076445] __arm64_sys_sendmsg+0x2c/0x40
[ 1417.076465] invoke_syscall+0x50/0x120
[ 1417.076486] el0_svc_common.constprop.0+0x48/0xf0
[ 1417.076506] do_el0_svc+0x24/0x38
[ 1417.076525] el0_svc+0x30/0x100
[ 1417.076548] el0t_64_sync_handler+0x100/0x130
[ 1417.076569] el0t_64_sync+0x190/0x198
[ 1417.076589] Code: f9401e80 aa1603e2 f9403be1 5280e483 (f9400000)
Fix this, by always using the vif corresponding to the wdev on which the
Action frame Transmission request was initiated by the userspace. This way,
even if P2P vif is not available, the IOVAR is sent to firmware on AP vif
and the ANQP Query RESP Action frame is transmitted without crashing the
driver.
Move init_completion() for "send_af_done" from brcmf_p2p_create_p2pdev()
to brcmf_p2p_attach(). Because the former function would not get executed
when only hostapd is managing wlan interface, and it is not safe to do
reinit_completion() later in brcmf_p2p_tx_action_frame(), without any prior
init_completion().
And in the brcmf_p2p_tx_action_frame() function, the condition check for
P2P Presence response frame is not needed, since the wpa_supplicant is
properly sending the P2P Presense Response frame on the P2P-GO vif instead
of the P2P-Device vif.
[Cc stable] |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix warning when putting transaction with qgroups enabled after abort
If we have a transaction abort with qgroups enabled we get a warning
triggered when doing the final put on the transaction, like this:
[552.6789] ------------[ cut here ]------------
[552.6815] WARNING: CPU: 4 PID: 81745 at fs/btrfs/transaction.c:144 btrfs_put_transaction+0x123/0x130 [btrfs]
[552.6817] Modules linked in: btrfs blake2b_generic xor (...)
[552.6819] CPU: 4 PID: 81745 Comm: btrfs-transacti Tainted: G W 6.4.0-rc6-btrfs-next-134+ #1
[552.6819] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
[552.6819] RIP: 0010:btrfs_put_transaction+0x123/0x130 [btrfs]
[552.6821] Code: bd a0 01 00 (...)
[552.6821] RSP: 0018:ffffa168c0527e28 EFLAGS: 00010286
[552.6821] RAX: ffff936042caed00 RBX: ffff93604a3eb448 RCX: 0000000000000000
[552.6821] RDX: ffff93606421b028 RSI: ffffffff92ff0878 RDI: ffff93606421b010
[552.6821] RBP: ffff93606421b000 R08: 0000000000000000 R09: ffffa168c0d07c20
[552.6821] R10: 0000000000000000 R11: ffff93608dc52950 R12: ffffa168c0527e70
[552.6821] R13: ffff93606421b000 R14: ffff93604a3eb420 R15: ffff93606421b028
[552.6821] FS: 0000000000000000(0000) GS:ffff93675fb00000(0000) knlGS:0000000000000000
[552.6821] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[552.6821] CR2: 0000558ad262b000 CR3: 000000014feda005 CR4: 0000000000370ee0
[552.6822] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[552.6822] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[552.6822] Call Trace:
[552.6822] <TASK>
[552.6822] ? __warn+0x80/0x130
[552.6822] ? btrfs_put_transaction+0x123/0x130 [btrfs]
[552.6824] ? report_bug+0x1f4/0x200
[552.6824] ? handle_bug+0x42/0x70
[552.6824] ? exc_invalid_op+0x14/0x70
[552.6824] ? asm_exc_invalid_op+0x16/0x20
[552.6824] ? btrfs_put_transaction+0x123/0x130 [btrfs]
[552.6826] btrfs_cleanup_transaction+0xe7/0x5e0 [btrfs]
[552.6828] ? _raw_spin_unlock_irqrestore+0x23/0x40
[552.6828] ? try_to_wake_up+0x94/0x5e0
[552.6828] ? __pfx_process_timeout+0x10/0x10
[552.6828] transaction_kthread+0x103/0x1d0 [btrfs]
[552.6830] ? __pfx_transaction_kthread+0x10/0x10 [btrfs]
[552.6832] kthread+0xee/0x120
[552.6832] ? __pfx_kthread+0x10/0x10
[552.6832] ret_from_fork+0x29/0x50
[552.6832] </TASK>
[552.6832] ---[ end trace 0000000000000000 ]---
This corresponds to this line of code:
void btrfs_put_transaction(struct btrfs_transaction *transaction)
{
(...)
WARN_ON(!RB_EMPTY_ROOT(
&transaction->delayed_refs.dirty_extent_root));
(...)
}
The warning happens because btrfs_qgroup_destroy_extent_records(), called
in the transaction abort path, we free all entries from the rbtree
"dirty_extent_root" with rbtree_postorder_for_each_entry_safe(), but we
don't actually empty the rbtree - it's still pointing to nodes that were
freed.
So set the rbtree's root node to NULL to avoid this warning (assign
RB_ROOT). |
| In the Linux kernel, the following vulnerability has been resolved:
perf/core: Fix system hang caused by cpu-clock usage
cpu-clock usage by the async-profiler tool can trigger a system hang,
which got bisected back to the following commit by Octavia Togami:
18dbcbfabfff ("perf: Fix the POLL_HUP delivery breakage") causes this issue
The root cause of the hang is that cpu-clock is a special type of SW
event which relies on hrtimers. The __perf_event_overflow() callback
is invoked from the hrtimer handler for cpu-clock events, and
__perf_event_overflow() tries to call cpu_clock_event_stop()
to stop the event, which calls htimer_cancel() to cancel the hrtimer.
But that's a recursion into the hrtimer code from a hrtimer handler,
which (unsurprisingly) deadlocks.
To fix this bug, use hrtimer_try_to_cancel() instead, and set
the PERF_HES_STOPPED flag, which causes perf_swevent_hrtimer()
to stop the event once it sees the PERF_HES_STOPPED flag.
[ mingo: Fixed the comments and improved the changelog. ] |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Add bpf_prog_run_data_pointers()
syzbot found that cls_bpf_classify() is able to change
tc_skb_cb(skb)->drop_reason triggering a warning in sk_skb_reason_drop().
WARNING: CPU: 0 PID: 5965 at net/core/skbuff.c:1192 __sk_skb_reason_drop net/core/skbuff.c:1189 [inline]
WARNING: CPU: 0 PID: 5965 at net/core/skbuff.c:1192 sk_skb_reason_drop+0x76/0x170 net/core/skbuff.c:1214
struct tc_skb_cb has been added in commit ec624fe740b4 ("net/sched:
Extend qdisc control block with tc control block"), which added a wrong
interaction with db58ba459202 ("bpf: wire in data and data_end for
cls_act_bpf").
drop_reason was added later.
Add bpf_prog_run_data_pointers() helper to save/restore the net_sched
storage colliding with BPF data_meta/data_end. |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: fix potential use-after-free bugs in TCP_Server_Info::hostname
TCP_Server_Info::hostname may be updated once or many times during
reconnect, so protect its access outside reconnect path as well and
then prevent any potential use-after-free bugs. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/chrome: cros_ec_ishtp: Fix UAF after unbinding driver
After unbinding the driver, another kthread `cros_ec_console_log_work`
is still accessing the device, resulting an UAF and crash.
The driver doesn't unregister the EC device in .remove() which should
shutdown sub-devices synchronously. Fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
caif: fix integer underflow in cffrml_receive()
The cffrml_receive() function extracts a length field from the packet
header and, when FCS is disabled, subtracts 2 from this length without
validating that len >= 2.
If an attacker sends a malicious packet with a length field of 0 or 1
to an interface with FCS disabled, the subtraction causes an integer
underflow.
This can lead to memory exhaustion and kernel instability, potential
information disclosure if padding contains uninitialized kernel memory.
Fix this by validating that len >= 2 before performing the subtraction. |
| In the Linux kernel, the following vulnerability has been resolved:
drivers: perf: marvell_cn10k: Fix hotplug callback leak in tad_pmu_init()
tad_pmu_init() won't remove the callback added by cpuhp_setup_state_multi()
when platform_driver_register() failed. Remove the callback by
cpuhp_remove_multi_state() in fail path.
Similar to the handling of arm_ccn_init() in commit 26242b330093 ("bus:
arm-ccn: Prevent hotplug callback leak") |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Cache streams targeting link when performing LT automation
[WHY]
Last LT automation update can cause crash by referencing current_state and
calling into dc_update_planes_and_stream which may clobber current_state.
[HOW]
Cache relevant stream pointers and iterate through them instead of relying
on the current_state. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to avoid updating zero-sized extent in extent cache
As syzbot reported:
F2FS-fs (loop0): __update_extent_tree_range: extent len is zero, type: 0, extent [0, 0, 0], age [0, 0]
------------[ cut here ]------------
kernel BUG at fs/f2fs/extent_cache.c:678!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 0 UID: 0 PID: 5336 Comm: syz.0.0 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
RIP: 0010:__update_extent_tree_range+0x13bc/0x1500 fs/f2fs/extent_cache.c:678
Call Trace:
<TASK>
f2fs_update_read_extent_cache_range+0x192/0x3e0 fs/f2fs/extent_cache.c:1085
f2fs_do_zero_range fs/f2fs/file.c:1657 [inline]
f2fs_zero_range+0x10c1/0x1580 fs/f2fs/file.c:1737
f2fs_fallocate+0x583/0x990 fs/f2fs/file.c:2030
vfs_fallocate+0x669/0x7e0 fs/open.c:342
ioctl_preallocate fs/ioctl.c:289 [inline]
file_ioctl+0x611/0x780 fs/ioctl.c:-1
do_vfs_ioctl+0xb33/0x1430 fs/ioctl.c:576
__do_sys_ioctl fs/ioctl.c:595 [inline]
__se_sys_ioctl+0x82/0x170 fs/ioctl.c:583
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f07bc58eec9
In error path of f2fs_zero_range(), it may add a zero-sized extent
into extent cache, it should be avoided. |
| In the Linux kernel, the following vulnerability has been resolved:
hfs: fix KMSAN uninit-value issue in hfs_find_set_zero_bits()
The syzbot reported issue in hfs_find_set_zero_bits():
=====================================================
BUG: KMSAN: uninit-value in hfs_find_set_zero_bits+0x74d/0xb60 fs/hfs/bitmap.c:45
hfs_find_set_zero_bits+0x74d/0xb60 fs/hfs/bitmap.c:45
hfs_vbm_search_free+0x13c/0x5b0 fs/hfs/bitmap.c:151
hfs_extend_file+0x6a5/0x1b00 fs/hfs/extent.c:408
hfs_get_block+0x435/0x1150 fs/hfs/extent.c:353
__block_write_begin_int+0xa76/0x3030 fs/buffer.c:2151
block_write_begin fs/buffer.c:2262 [inline]
cont_write_begin+0x10e1/0x1bc0 fs/buffer.c:2601
hfs_write_begin+0x85/0x130 fs/hfs/inode.c:52
cont_expand_zero fs/buffer.c:2528 [inline]
cont_write_begin+0x35a/0x1bc0 fs/buffer.c:2591
hfs_write_begin+0x85/0x130 fs/hfs/inode.c:52
hfs_file_truncate+0x1d6/0xe60 fs/hfs/extent.c:494
hfs_inode_setattr+0x964/0xaa0 fs/hfs/inode.c:654
notify_change+0x1993/0x1aa0 fs/attr.c:552
do_truncate+0x28f/0x310 fs/open.c:68
do_ftruncate+0x698/0x730 fs/open.c:195
do_sys_ftruncate fs/open.c:210 [inline]
__do_sys_ftruncate fs/open.c:215 [inline]
__se_sys_ftruncate fs/open.c:213 [inline]
__x64_sys_ftruncate+0x11b/0x250 fs/open.c:213
x64_sys_call+0xfe3/0x3db0 arch/x86/include/generated/asm/syscalls_64.h:78
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xd9/0x210 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Uninit was created at:
slab_post_alloc_hook mm/slub.c:4154 [inline]
slab_alloc_node mm/slub.c:4197 [inline]
__kmalloc_cache_noprof+0x7f7/0xed0 mm/slub.c:4354
kmalloc_noprof include/linux/slab.h:905 [inline]
hfs_mdb_get+0x1cc8/0x2a90 fs/hfs/mdb.c:175
hfs_fill_super+0x3d0/0xb80 fs/hfs/super.c:337
get_tree_bdev_flags+0x6e3/0x920 fs/super.c:1681
get_tree_bdev+0x38/0x50 fs/super.c:1704
hfs_get_tree+0x35/0x40 fs/hfs/super.c:388
vfs_get_tree+0xb0/0x5c0 fs/super.c:1804
do_new_mount+0x738/0x1610 fs/namespace.c:3902
path_mount+0x6db/0x1e90 fs/namespace.c:4226
do_mount fs/namespace.c:4239 [inline]
__do_sys_mount fs/namespace.c:4450 [inline]
__se_sys_mount+0x6eb/0x7d0 fs/namespace.c:4427
__x64_sys_mount+0xe4/0x150 fs/namespace.c:4427
x64_sys_call+0xfa7/0x3db0 arch/x86/include/generated/asm/syscalls_64.h:166
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xd9/0x210 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
CPU: 1 UID: 0 PID: 12609 Comm: syz.1.2692 Not tainted 6.16.0-syzkaller #0 PREEMPT(none)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/12/2025
=====================================================
The HFS_SB(sb)->bitmap buffer is allocated in hfs_mdb_get():
HFS_SB(sb)->bitmap = kmalloc(8192, GFP_KERNEL);
Finally, it can trigger the reported issue because kmalloc()
doesn't clear the allocated memory. If allocated memory contains
only zeros, then everything will work pretty fine.
But if the allocated memory contains the "garbage", then
it can affect the bitmap operations and it triggers
the reported issue.
This patch simply exchanges the kmalloc() on kzalloc()
with the goal to guarantee the correctness of bitmap operations.
Because, newly created allocation bitmap should have all
available blocks free. Potentially, initialization bitmap's read
operation could not fill the whole allocated memory and
"garbage" in the not initialized memory will be the reason of
volume coruptions and file system driver bugs. |
| In the Linux kernel, the following vulnerability has been resolved:
iommufd: Set end correctly when doing batch carry
Even though the test suite covers this it somehow became obscured that
this wasn't working.
The test iommufd_ioas.mock_domain.access_domain_destory would blow up
rarely.
end should be set to 1 because this just pushed an item, the carry, to the
pfns list.
Sometimes the test would blow up with:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] SMP
CPU: 5 PID: 584 Comm: iommufd Not tainted 6.5.0-rc1-dirty #1236
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:batch_unpin+0xa2/0x100 [iommufd]
Code: 17 48 81 fe ff ff 07 00 77 70 48 8b 15 b7 be 97 e2 48 85 d2 74 14 48 8b 14 fa 48 85 d2 74 0b 40 0f b6 f6 48 c1 e6 04 48 01 f2 <48> 8b 3a 48 c1 e0 06 89 ca 48 89 de 48 83 e7 f0 48 01 c7 e8 96 dc
RSP: 0018:ffffc90001677a58 EFLAGS: 00010246
RAX: 00007f7e2646f000 RBX: 0000000000000000 RCX: 0000000000000001
RDX: 0000000000000000 RSI: 00000000fefc4c8d RDI: 0000000000fefc4c
RBP: ffffc90001677a80 R08: 0000000000000048 R09: 0000000000000200
R10: 0000000000030b98 R11: ffffffff81f3bb40 R12: 0000000000000001
R13: ffff888101f75800 R14: ffffc90001677ad0 R15: 00000000000001fe
FS: 00007f9323679740(0000) GS:ffff8881ba540000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000000105ede003 CR4: 00000000003706a0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
? show_regs+0x5c/0x70
? __die+0x1f/0x60
? page_fault_oops+0x15d/0x440
? lock_release+0xbc/0x240
? exc_page_fault+0x4a4/0x970
? asm_exc_page_fault+0x27/0x30
? batch_unpin+0xa2/0x100 [iommufd]
? batch_unpin+0xba/0x100 [iommufd]
__iopt_area_unfill_domain+0x198/0x430 [iommufd]
? __mutex_lock+0x8c/0xb80
? __mutex_lock+0x6aa/0xb80
? xa_erase+0x28/0x30
? iopt_table_remove_domain+0x162/0x320 [iommufd]
? lock_release+0xbc/0x240
iopt_area_unfill_domain+0xd/0x10 [iommufd]
iopt_table_remove_domain+0x195/0x320 [iommufd]
iommufd_hw_pagetable_destroy+0xb3/0x110 [iommufd]
iommufd_object_destroy_user+0x8e/0xf0 [iommufd]
iommufd_device_detach+0xc5/0x140 [iommufd]
iommufd_selftest_destroy+0x1f/0x70 [iommufd]
iommufd_object_destroy_user+0x8e/0xf0 [iommufd]
iommufd_destroy+0x3a/0x50 [iommufd]
iommufd_fops_ioctl+0xfb/0x170 [iommufd]
__x64_sys_ioctl+0x40d/0x9a0
do_syscall_64+0x3c/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0 |
| In the Linux kernel, the following vulnerability has been resolved:
rpmsg: glink: Add check for kstrdup
Add check for the return value of kstrdup() and return the error
if it fails in order to avoid NULL pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mdio: Check regmap pointer returned by device_node_to_regmap()
The call to device_node_to_regmap() in airoha_mdio_probe() can return
an ERR_PTR() if regmap initialization fails. Currently, the driver
stores the pointer without validation, which could lead to a crash
if it is later dereferenced.
Add an IS_ERR() check and return the corresponding error code to make
the probe path more robust. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8192u: Fix use after free in ieee80211_rx()
We cannot dereference the "skb" pointer after calling
ieee80211_monitor_rx(), because it is a use after free. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/hns: Fix refcount leak in hns_roce_mmap
rdma_user_mmap_entry_get_pgoff() takes the reference.
Add missing rdma_user_mmap_entry_put() to release the reference.
Acked-by Haoyue Xu <xuhaoyue1@hisilicon.com> |
| In the Linux kernel, the following vulnerability has been resolved:
ovl: fix null pointer dereference in ovl_get_acl_rcu()
Following process:
P1 P2
path_openat
link_path_walk
may_lookup
inode_permission(rcu)
ovl_permission
acl_permission_check
check_acl
get_cached_acl_rcu
ovl_get_inode_acl
realinode = ovl_inode_real(ovl_inode)
drop_cache
__dentry_kill(ovl_dentry)
iput(ovl_inode)
ovl_destroy_inode(ovl_inode)
dput(oi->__upperdentry)
dentry_kill(upperdentry)
dentry_unlink_inode
upperdentry->d_inode = NULL
ovl_inode_upper
upperdentry = ovl_i_dentry_upper(ovl_inode)
d_inode(upperdentry) // returns NULL
IS_POSIXACL(realinode) // NULL pointer dereference
, will trigger an null pointer dereference at realinode:
[ 205.472797] BUG: kernel NULL pointer dereference, address:
0000000000000028
[ 205.476701] CPU: 2 PID: 2713 Comm: ls Not tainted
6.3.0-12064-g2edfa098e750-dirty #1216
[ 205.478754] RIP: 0010:do_ovl_get_acl+0x5d/0x300
[ 205.489584] Call Trace:
[ 205.489812] <TASK>
[ 205.490014] ovl_get_inode_acl+0x26/0x30
[ 205.490466] get_cached_acl_rcu+0x61/0xa0
[ 205.490908] generic_permission+0x1bf/0x4e0
[ 205.491447] ovl_permission+0x79/0x1b0
[ 205.491917] inode_permission+0x15e/0x2c0
[ 205.492425] link_path_walk+0x115/0x550
[ 205.493311] path_lookupat.isra.0+0xb2/0x200
[ 205.493803] filename_lookup+0xda/0x240
[ 205.495747] vfs_fstatat+0x7b/0xb0
Fetch a reproducer in [Link].
Use the helper ovl_i_path_realinode() to get realinode and then do
non-nullptr checking. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Disable preemption in bpf_perf_event_output
The nesting protection in bpf_perf_event_output relies on disabled
preemption, which is guaranteed for kprobes and tracepoints.
However bpf_perf_event_output can be also called from uprobes context
through bpf_prog_run_array_sleepable function which disables migration,
but keeps preemption enabled.
This can cause task to be preempted by another one inside the nesting
protection and lead eventually to two tasks using same perf_sample_data
buffer and cause crashes like:
kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
BUG: unable to handle page fault for address: ffffffff82be3eea
...
Call Trace:
? __die+0x1f/0x70
? page_fault_oops+0x176/0x4d0
? exc_page_fault+0x132/0x230
? asm_exc_page_fault+0x22/0x30
? perf_output_sample+0x12b/0x910
? perf_event_output+0xd0/0x1d0
? bpf_perf_event_output+0x162/0x1d0
? bpf_prog_c6271286d9a4c938_krava1+0x76/0x87
? __uprobe_perf_func+0x12b/0x540
? uprobe_dispatcher+0x2c4/0x430
? uprobe_notify_resume+0x2da/0xce0
? atomic_notifier_call_chain+0x7b/0x110
? exit_to_user_mode_prepare+0x13e/0x290
? irqentry_exit_to_user_mode+0x5/0x30
? asm_exc_int3+0x35/0x40
Fixing this by disabling preemption in bpf_perf_event_output. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: spi-nor: Fix shift-out-of-bounds in spi_nor_set_erase_type
spi_nor_set_erase_type() was used either to set or to mask out an erase
type. When we used it to mask out an erase type a shift-out-of-bounds
was hit:
UBSAN: shift-out-of-bounds in drivers/mtd/spi-nor/core.c:2237:24
shift exponent 4294967295 is too large for 32-bit type 'int'
The setting of the size_{shift, mask} and of the opcode are unnecessary
when the erase size is zero, as throughout the code just the erase size
is considered to determine whether an erase type is supported or not.
Setting the opcode to 0xFF was wrong too as nobody guarantees that 0xFF
is an unused opcode. Thus when masking out an erase type, just set the
erase size to zero. This will fix the shift-out-of-bounds.
[ta: refine changes, new commit message, fix compilation error] |
