| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
mmc: atmel-mci: fix return value check of mmc_add_host()
mmc_add_host() may return error, if we ignore its return value,
it will lead two issues:
1. The memory that allocated in mmc_alloc_host() is leaked.
2. In the remove() path, mmc_remove_host() will be called to
delete device, but it's not added yet, it will lead a kernel
crash because of null-ptr-deref in device_del().
So fix this by checking the return value and calling mmc_free_host()
in the error path. |
| In the Linux kernel, the following vulnerability has been resolved:
inet: frags: flush pending skbs in fqdir_pre_exit()
We have been seeing occasional deadlocks on pernet_ops_rwsem since
September in NIPA. The stuck task was usually modprobe (often loading
a driver like ipvlan), trying to take the lock as a Writer.
lockdep does not track readers for rwsems so the read wasn't obvious
from the reports.
On closer inspection the Reader holding the lock was conntrack looping
forever in nf_conntrack_cleanup_net_list(). Based on past experience
with occasional NIPA crashes I looked thru the tests which run before
the crash and noticed that the crash follows ip_defrag.sh. An immediate
red flag. Scouring thru (de)fragmentation queues reveals skbs sitting
around, holding conntrack references.
The problem is that since conntrack depends on nf_defrag_ipv6,
nf_defrag_ipv6 will load first. Since nf_defrag_ipv6 loads first its
netns exit hooks run _after_ conntrack's netns exit hook.
Flush all fragment queue SKBs during fqdir_pre_exit() to release
conntrack references before conntrack cleanup runs. Also flush
the queues in timer expiry handlers when they discover fqdir->dead
is set, in case packet sneaks in while we're running the pre_exit
flush.
The commit under Fixes is not exactly the culprit, but I think
previously the timer firing would eventually unblock the spinning
conntrack. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: Fix possible use-after-free in async command interface
mlx5_cmd_cleanup_async_ctx should return only after all its callback
handlers were completed. Before this patch, the below race between
mlx5_cmd_cleanup_async_ctx and mlx5_cmd_exec_cb_handler was possible and
lead to a use-after-free:
1. mlx5_cmd_cleanup_async_ctx is called while num_inflight is 2 (i.e.
elevated by 1, a single inflight callback).
2. mlx5_cmd_cleanup_async_ctx decreases num_inflight to 1.
3. mlx5_cmd_exec_cb_handler is called, decreases num_inflight to 0 and
is about to call wake_up().
4. mlx5_cmd_cleanup_async_ctx calls wait_event, which returns
immediately as the condition (num_inflight == 0) holds.
5. mlx5_cmd_cleanup_async_ctx returns.
6. The caller of mlx5_cmd_cleanup_async_ctx frees the mlx5_async_ctx
object.
7. mlx5_cmd_exec_cb_handler goes on and calls wake_up() on the freed
object.
Fix it by syncing using a completion object. Mark it completed when
num_inflight reaches 0.
Trace:
BUG: KASAN: use-after-free in do_raw_spin_lock+0x23d/0x270
Read of size 4 at addr ffff888139cd12f4 by task swapper/5/0
CPU: 5 PID: 0 Comm: swapper/5 Not tainted 6.0.0-rc3_for_upstream_debug_2022_08_30_13_10 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x57/0x7d
print_report.cold+0x2d5/0x684
? do_raw_spin_lock+0x23d/0x270
kasan_report+0xb1/0x1a0
? do_raw_spin_lock+0x23d/0x270
do_raw_spin_lock+0x23d/0x270
? rwlock_bug.part.0+0x90/0x90
? __delete_object+0xb8/0x100
? lock_downgrade+0x6e0/0x6e0
_raw_spin_lock_irqsave+0x43/0x60
? __wake_up_common_lock+0xb9/0x140
__wake_up_common_lock+0xb9/0x140
? __wake_up_common+0x650/0x650
? destroy_tis_callback+0x53/0x70 [mlx5_core]
? kasan_set_track+0x21/0x30
? destroy_tis_callback+0x53/0x70 [mlx5_core]
? kfree+0x1ba/0x520
? do_raw_spin_unlock+0x54/0x220
mlx5_cmd_exec_cb_handler+0x136/0x1a0 [mlx5_core]
? mlx5_cmd_cleanup_async_ctx+0x220/0x220 [mlx5_core]
? mlx5_cmd_cleanup_async_ctx+0x220/0x220 [mlx5_core]
mlx5_cmd_comp_handler+0x65a/0x12b0 [mlx5_core]
? dump_command+0xcc0/0xcc0 [mlx5_core]
? lockdep_hardirqs_on_prepare+0x400/0x400
? cmd_comp_notifier+0x7e/0xb0 [mlx5_core]
cmd_comp_notifier+0x7e/0xb0 [mlx5_core]
atomic_notifier_call_chain+0xd7/0x1d0
mlx5_eq_async_int+0x3ce/0xa20 [mlx5_core]
atomic_notifier_call_chain+0xd7/0x1d0
? irq_release+0x140/0x140 [mlx5_core]
irq_int_handler+0x19/0x30 [mlx5_core]
__handle_irq_event_percpu+0x1f2/0x620
handle_irq_event+0xb2/0x1d0
handle_edge_irq+0x21e/0xb00
__common_interrupt+0x79/0x1a0
common_interrupt+0x78/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:default_idle+0x42/0x60
Code: c1 83 e0 07 48 c1 e9 03 83 c0 03 0f b6 14 11 38 d0 7c 04 84 d2 75 14 8b 05 eb 47 22 02 85 c0 7e 07 0f 00 2d e0 9f 48 00 fb f4 <c3> 48 c7 c7 80 08 7f 85 e8 d1 d3 3e fe eb de 66 66 2e 0f 1f 84 00
RSP: 0018:ffff888100dbfdf0 EFLAGS: 00000242
RAX: 0000000000000001 RBX: ffffffff84ecbd48 RCX: 1ffffffff0afe110
RDX: 0000000000000004 RSI: 0000000000000000 RDI: ffffffff835cc9bc
RBP: 0000000000000005 R08: 0000000000000001 R09: ffff88881dec4ac3
R10: ffffed1103bd8958 R11: 0000017d0ca571c9 R12: 0000000000000005
R13: ffffffff84f024e0 R14: 0000000000000000 R15: dffffc0000000000
? default_idle_call+0xcc/0x450
default_idle_call+0xec/0x450
do_idle+0x394/0x450
? arch_cpu_idle_exit+0x40/0x40
? do_idle+0x17/0x450
cpu_startup_entry+0x19/0x20
start_secondary+0x221/0x2b0
? set_cpu_sibling_map+0x2070/0x2070
secondary_startup_64_no_verify+0xcd/0xdb
</TASK>
Allocated by task 49502:
kasan_save_stack+0x1e/0x40
__kasan_kmalloc+0x81/0xa0
kvmalloc_node+0x48/0xe0
mlx5e_bulk_async_init+0x35/0x110 [mlx5_core]
mlx5e_tls_priv_tx_list_cleanup+0x84/0x3e0 [mlx5_core]
mlx5e_ktls_cleanup_tx+0x38f/0x760 [mlx5_core]
mlx5e_cleanup_nic_tx+0xa7/0x100 [mlx5_core]
mlx5e_detach_netdev+0x1c
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix panic due to wrong pageattr of im->image
In the scenario where livepatch and kretfunc coexist, the pageattr of
im->image is rox after arch_prepare_bpf_trampoline in
bpf_trampoline_update, and then modify_fentry or register_fentry returns
-EAGAIN from bpf_tramp_ftrace_ops_func, the BPF_TRAMP_F_ORIG_STACK flag
will be configured, and arch_prepare_bpf_trampoline will be re-executed.
At this time, because the pageattr of im->image is rox,
arch_prepare_bpf_trampoline will read and write im->image, which causes
a fault. as follows:
insmod livepatch-sample.ko # samples/livepatch/livepatch-sample.c
bpftrace -e 'kretfunc:cmdline_proc_show {}'
BUG: unable to handle page fault for address: ffffffffa0206000
PGD 322d067 P4D 322d067 PUD 322e063 PMD 1297e067 PTE d428061
Oops: 0003 [#1] PREEMPT SMP PTI
CPU: 2 PID: 270 Comm: bpftrace Tainted: G E K 6.1.0 #5
RIP: 0010:arch_prepare_bpf_trampoline+0xed/0x8c0
RSP: 0018:ffffc90001083ad8 EFLAGS: 00010202
RAX: ffffffffa0206000 RBX: 0000000000000020 RCX: 0000000000000000
RDX: ffffffffa0206001 RSI: ffffffffa0206000 RDI: 0000000000000030
RBP: ffffc90001083b70 R08: 0000000000000066 R09: ffff88800f51b400
R10: 000000002e72c6e5 R11: 00000000d0a15080 R12: ffff8880110a68c8
R13: 0000000000000000 R14: ffff88800f51b400 R15: ffffffff814fec10
FS: 00007f87bc0dc780(0000) GS:ffff88803e600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffa0206000 CR3: 0000000010b70000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
bpf_trampoline_update+0x25a/0x6b0
__bpf_trampoline_link_prog+0x101/0x240
bpf_trampoline_link_prog+0x2d/0x50
bpf_tracing_prog_attach+0x24c/0x530
bpf_raw_tp_link_attach+0x73/0x1d0
__sys_bpf+0x100e/0x2570
__x64_sys_bpf+0x1c/0x30
do_syscall_64+0x5b/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
With this patch, when modify_fentry or register_fentry returns -EAGAIN
from bpf_tramp_ftrace_ops_func, the pageattr of im->image will be reset
to nx+rw. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: multiq3: sanitize config options in multiq3_attach()
Syzbot identified an issue [1] in multiq3_attach() that induces a
task timeout due to open() or COMEDI_DEVCONFIG ioctl operations,
specifically, in the case of multiq3 driver.
This problem arose when syzkaller managed to craft weird configuration
options used to specify the number of channels in encoder subdevice.
If a particularly great number is passed to s->n_chan in
multiq3_attach() via it->options[2], then multiple calls to
multiq3_encoder_reset() at the end of driver-specific attach() method
will be running for minutes, thus blocking tasks and affected devices
as well.
While this issue is most likely not too dangerous for real-life
devices, it still makes sense to sanitize configuration inputs. Enable
a sensible limit on the number of encoder chips (4 chips max, each
with 2 channels) to stop this behaviour from manifesting.
[1] Syzbot crash:
INFO: task syz.2.19:6067 blocked for more than 143 seconds.
...
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5254 [inline]
__schedule+0x17c4/0x4d60 kernel/sched/core.c:6862
__schedule_loop kernel/sched/core.c:6944 [inline]
schedule+0x165/0x360 kernel/sched/core.c:6959
schedule_preempt_disabled+0x13/0x30 kernel/sched/core.c:7016
__mutex_lock_common kernel/locking/mutex.c:676 [inline]
__mutex_lock+0x7e6/0x1350 kernel/locking/mutex.c:760
comedi_open+0xc0/0x590 drivers/comedi/comedi_fops.c:2868
chrdev_open+0x4cc/0x5e0 fs/char_dev.c:414
do_dentry_open+0x953/0x13f0 fs/open.c:965
vfs_open+0x3b/0x340 fs/open.c:1097
... |
| In the Linux kernel, the following vulnerability has been resolved:
hwrng: geode - Fix PCI device refcount leak
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. We add a new struct
'amd_geode_priv' to record pointer of the pci_dev and membase, and then
add missing pci_dev_put() for the normal and error path. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix stack buffer overflow in OnAssocReq IE parsing
The Supported Rates IE length from an incoming Association Request frame
was used directly as the memcpy() length when copying into a fixed-size
16-byte stack buffer (supportRate). A malicious station can advertise an
IE length larger than 16 bytes, causing a stack buffer overflow.
Clamp ie_len to the buffer size before copying the Supported Rates IE,
and correct the bounds check when merging Extended Supported Rates to
prevent a second potential overflow.
This prevents kernel stack corruption triggered by malformed association
requests. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix out-of-bounds read in OnBeacon ESR IE parsing
The Extended Supported Rates (ESR) IE handling in OnBeacon accessed
*(p + 1 + ielen) and *(p + 2 + ielen) without verifying that these
offsets lie within the received frame buffer. A malformed beacon with
an ESR IE positioned at the end of the buffer could cause an
out-of-bounds read, potentially triggering a kernel panic.
Add a boundary check to ensure that the ESR IE body and the subsequent
bytes are within the limits of the frame before attempting to access
them.
This prevents OOB reads caused by malformed beacon frames. |
| In the Linux kernel, the following vulnerability has been resolved:
most: usb: hdm_probe: Fix calling put_device() before device initialization
The early error path in hdm_probe() can jump to err_free_mdev before
&mdev->dev has been initialized with device_initialize(). Calling
put_device(&mdev->dev) there triggers a device core WARN and ends up
invoking kref_put(&kobj->kref, kobject_release) on an uninitialized
kobject.
In this path the private struct was only kmalloc'ed and the intended
release is effectively kfree(mdev) anyway, so free it directly instead
of calling put_device() on an uninitialized device.
This removes the WARNING and fixes the pre-initialization error path. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915: Avoid lock inversion when pinning to GGTT on CHV/BXT+VTD
On completion of i915_vma_pin_ww(), a synchronous variant of
dma_fence_work_commit() is called. When pinning a VMA to GGTT address
space on a Cherry View family processor, or on a Broxton generation SoC
with VTD enabled, i.e., when stop_machine() is then called from
intel_ggtt_bind_vma(), that can potentially lead to lock inversion among
reservation_ww and cpu_hotplug locks.
[86.861179] ======================================================
[86.861193] WARNING: possible circular locking dependency detected
[86.861209] 6.15.0-rc5-CI_DRM_16515-gca0305cadc2d+ #1 Tainted: G U
[86.861226] ------------------------------------------------------
[86.861238] i915_module_loa/1432 is trying to acquire lock:
[86.861252] ffffffff83489090 (cpu_hotplug_lock){++++}-{0:0}, at: stop_machine+0x1c/0x50
[86.861290]
but task is already holding lock:
[86.861303] ffffc90002e0b4c8 (reservation_ww_class_mutex){+.+.}-{3:3}, at: i915_vma_pin.constprop.0+0x39/0x1d0 [i915]
[86.862233]
which lock already depends on the new lock.
[86.862251]
the existing dependency chain (in reverse order) is:
[86.862265]
-> #5 (reservation_ww_class_mutex){+.+.}-{3:3}:
[86.862292] dma_resv_lockdep+0x19a/0x390
[86.862315] do_one_initcall+0x60/0x3f0
[86.862334] kernel_init_freeable+0x3cd/0x680
[86.862353] kernel_init+0x1b/0x200
[86.862369] ret_from_fork+0x47/0x70
[86.862383] ret_from_fork_asm+0x1a/0x30
[86.862399]
-> #4 (reservation_ww_class_acquire){+.+.}-{0:0}:
[86.862425] dma_resv_lockdep+0x178/0x390
[86.862440] do_one_initcall+0x60/0x3f0
[86.862454] kernel_init_freeable+0x3cd/0x680
[86.862470] kernel_init+0x1b/0x200
[86.862482] ret_from_fork+0x47/0x70
[86.862495] ret_from_fork_asm+0x1a/0x30
[86.862509]
-> #3 (&mm->mmap_lock){++++}-{3:3}:
[86.862531] down_read_killable+0x46/0x1e0
[86.862546] lock_mm_and_find_vma+0xa2/0x280
[86.862561] do_user_addr_fault+0x266/0x8e0
[86.862578] exc_page_fault+0x8a/0x2f0
[86.862593] asm_exc_page_fault+0x27/0x30
[86.862607] filldir64+0xeb/0x180
[86.862620] kernfs_fop_readdir+0x118/0x480
[86.862635] iterate_dir+0xcf/0x2b0
[86.862648] __x64_sys_getdents64+0x84/0x140
[86.862661] x64_sys_call+0x1058/0x2660
[86.862675] do_syscall_64+0x91/0xe90
[86.862689] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[86.862703]
-> #2 (&root->kernfs_rwsem){++++}-{3:3}:
[86.862725] down_write+0x3e/0xf0
[86.862738] kernfs_add_one+0x30/0x3c0
[86.862751] kernfs_create_dir_ns+0x53/0xb0
[86.862765] internal_create_group+0x134/0x4c0
[86.862779] sysfs_create_group+0x13/0x20
[86.862792] topology_add_dev+0x1d/0x30
[86.862806] cpuhp_invoke_callback+0x4b5/0x850
[86.862822] cpuhp_issue_call+0xbf/0x1f0
[86.862836] __cpuhp_setup_state_cpuslocked+0x111/0x320
[86.862852] __cpuhp_setup_state+0xb0/0x220
[86.862866] topology_sysfs_init+0x30/0x50
[86.862879] do_one_initcall+0x60/0x3f0
[86.862893] kernel_init_freeable+0x3cd/0x680
[86.862908] kernel_init+0x1b/0x200
[86.862921] ret_from_fork+0x47/0x70
[86.862934] ret_from_fork_asm+0x1a/0x30
[86.862947]
-> #1 (cpuhp_state_mutex){+.+.}-{3:3}:
[86.862969] __mutex_lock+0xaa/0xed0
[86.862982] mutex_lock_nested+0x1b/0x30
[86.862995] __cpuhp_setup_state_cpuslocked+0x67/0x320
[86.863012] __cpuhp_setup_state+0xb0/0x220
[86.863026] page_alloc_init_cpuhp+0x2d/0x60
[86.863041] mm_core_init+0x22/0x2d0
[86.863054] start_kernel+0x576/0xbd0
[86.863068] x86_64_start_reservations+0x18/0x30
[86.863084] x86_64_start_kernel+0xbf/0x110
[86.863098] common_startup_64+0x13e/0x141
[86.863114]
-> #0 (cpu_hotplug_lock){++++}-{0:0}:
[86.863135] __lock_acquire+0x16
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
posix-timers: Prevent RT livelock in itimer_delete()
itimer_delete() has a retry loop when the timer is concurrently expired. On
non-RT kernels this just spin-waits until the timer callback has completed,
except for posix CPU timers which have HAVE_POSIX_CPU_TIMERS_TASK_WORK
enabled.
In that case and on RT kernels the existing task could live lock when
preempting the task which does the timer delivery.
Replace spin_unlock() with an invocation of timer_wait_running() to handle
it the same way as the other retry loops in the posix timer code. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: rawnand: cadence: fix DMA device NULL pointer dereference
The DMA device pointer `dma_dev` was being dereferenced before ensuring
that `cdns_ctrl->dmac` is properly initialized.
Move the assignment of `dma_dev` after successfully acquiring the DMA
channel to ensure the pointer is valid before use. |
| In the Linux kernel, the following vulnerability has been resolved:
mtdchar: fix integer overflow in read/write ioctls
The "req.start" and "req.len" variables are u64 values that come from the
user at the start of the function. We mask away the high 32 bits of
"req.len" so that's capped at U32_MAX but the "req.start" variable can go
up to U64_MAX which means that the addition can still integer overflow.
Use check_add_overflow() to fix this bug. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/tegra: Add call to put_pid()
Add a call to put_pid() corresponding to get_task_pid().
host1x_memory_context_alloc() does not take ownership of the PID so we
need to free it here to avoid leaking.
[mperttunen@nvidia.com: reword commit message] |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: stacktrace: Disable KASAN checks for non-current tasks
Unwinding the stack of a task other than current, KASAN would report
"BUG: KASAN: out-of-bounds in walk_stackframe+0x41c/0x460"
There is a same issue on x86 and has been resolved by the commit
84936118bdf3 ("x86/unwind: Disable KASAN checks for non-current tasks")
The solution could be applied to RISC-V too.
This patch also can solve the issue:
https://seclists.org/oss-sec/2025/q4/23
[pjw@kernel.org: clean up checkpatch issues] |
| In the Linux kernel, the following vulnerability has been resolved:
mm/mempool: fix poisoning order>0 pages with HIGHMEM
The kernel test has reported:
BUG: unable to handle page fault for address: fffba000
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
*pde = 03171067 *pte = 00000000
Oops: Oops: 0002 [#1]
CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Tainted: G T 6.18.0-rc2-00031-gec7f31b2a2d3 #1 NONE a1d066dfe789f54bc7645c7989957d2bdee593ca
Tainted: [T]=RANDSTRUCT
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
EIP: memset (arch/x86/include/asm/string_32.h:168 arch/x86/lib/memcpy_32.c:17)
Code: a5 8b 4d f4 83 e1 03 74 02 f3 a4 83 c4 04 5e 5f 5d 2e e9 73 41 01 00 90 90 90 3e 8d 74 26 00 55 89 e5 57 56 89 c6 89 d0 89 f7 <f3> aa 89 f0 5e 5f 5d 2e e9 53 41 01 00 cc cc cc 55 89 e5 53 57 56
EAX: 0000006b EBX: 00000015 ECX: 001fefff EDX: 0000006b
ESI: fffb9000 EDI: fffba000 EBP: c611fbf0 ESP: c611fbe8
DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068 EFLAGS: 00010287
CR0: 80050033 CR2: fffba000 CR3: 0316e000 CR4: 00040690
Call Trace:
poison_element (mm/mempool.c:83 mm/mempool.c:102)
mempool_init_node (mm/mempool.c:142 mm/mempool.c:226)
mempool_init_noprof (mm/mempool.c:250 (discriminator 1))
? mempool_alloc_pages (mm/mempool.c:640)
bio_integrity_initfn (block/bio-integrity.c:483 (discriminator 8))
? mempool_alloc_pages (mm/mempool.c:640)
do_one_initcall (init/main.c:1283)
Christoph found out this is due to the poisoning code not dealing
properly with CONFIG_HIGHMEM because only the first page is mapped but
then the whole potentially high-order page is accessed.
We could give up on HIGHMEM here, but it's straightforward to fix this
with a loop that's mapping, poisoning or checking and unmapping
individual pages. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: Fix proto fallback detection with BPF
The sockmap feature allows bpf syscall from userspace, or based
on bpf sockops, replacing the sk_prot of sockets during protocol stack
processing with sockmap's custom read/write interfaces.
'''
tcp_rcv_state_process()
syn_recv_sock()/subflow_syn_recv_sock()
tcp_init_transfer(BPF_SOCK_OPS_PASSIVE_ESTABLISHED_CB)
bpf_skops_established <== sockops
bpf_sock_map_update(sk) <== call bpf helper
tcp_bpf_update_proto() <== update sk_prot
'''
When the server has MPTCP enabled but the client sends a TCP SYN
without MPTCP, subflow_syn_recv_sock() performs a fallback on the
subflow, replacing the subflow sk's sk_prot with the native sk_prot.
'''
subflow_syn_recv_sock()
subflow_ulp_fallback()
subflow_drop_ctx()
mptcp_subflow_ops_undo_override()
'''
Then, this subflow can be normally used by sockmap, which replaces the
native sk_prot with sockmap's custom sk_prot. The issue occurs when the
user executes accept::mptcp_stream_accept::mptcp_fallback_tcp_ops().
Here, it uses sk->sk_prot to compare with the native sk_prot, but this
is incorrect when sockmap is used, as we may incorrectly set
sk->sk_socket->ops.
This fix uses the more generic sk_family for the comparison instead.
Additionally, this also prevents a WARNING from occurring:
result from ./scripts/decode_stacktrace.sh:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 337 at net/mptcp/protocol.c:68 mptcp_stream_accept \
(net/mptcp/protocol.c:4005)
Modules linked in:
...
PKRU: 55555554
Call Trace:
<TASK>
do_accept (net/socket.c:1989)
__sys_accept4 (net/socket.c:2028 net/socket.c:2057)
__x64_sys_accept (net/socket.c:2067)
x64_sys_call (arch/x86/entry/syscall_64.c:41)
do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
RIP: 0033:0x7f87ac92b83d
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix rbtree traversal bug in ext4_mb_use_preallocated
During allocations, while looking for preallocations(PA) in the per
inode rbtree, we can't do a direct traversal of the tree because
ext4_mb_discard_group_preallocation() can paralelly mark the pa deleted
and that can cause direct traversal to skip some entries. This was
leading to a BUG_ON() being hit [1] when we missed a PA that could satisfy
our request and ultimately tried to create a new PA that would overlap
with the missed one.
To makes sure we handle that case while still keeping the performance of
the rbtree, we make use of the fact that the only pa that could possibly
overlap the original goal start is the one that satisfies the below
conditions:
1. It must have it's logical start immediately to the left of
(ie less than) original logical start.
2. It must not be deleted
To find this pa we use the following traversal method:
1. Descend into the rbtree normally to find the immediate neighboring
PA. Here we keep descending irrespective of if the PA is deleted or if
it overlaps with our request etc. The goal is to find an immediately
adjacent PA.
2. If the found PA is on right of original goal, use rb_prev() to find
the left adjacent PA.
3. Check if this PA is deleted and keep moving left with rb_prev() until
a non deleted PA is found.
4. This is the PA we are looking for. Now we can check if it can satisfy
the original request and proceed accordingly.
This approach also takes care of having deleted PAs in the tree.
(While we are at it, also fix a possible overflow bug in calculating the
end of a PA)
[1] https://lore.kernel.org/linux-ext4/CA+G9fYv2FRpLqBZf34ZinR8bU2_ZRAUOjKAD3+tKRFaEQHtt8Q@mail.gmail.com/ |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: marvell/octeontx - prevent integer overflows
The "code_length" value comes from the firmware file. If your firmware
is untrusted realistically there is probably very little you can do to
protect yourself. Still we try to limit the damage as much as possible.
Also Smatch marks any data read from the filesystem as untrusted and
prints warnings if it not capped correctly.
The "code_length * 2" can overflow. The round_up(ucode_size, 16) +
sizeof() expression can overflow too. Prevent these overflows. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: NFSv4 file creation neglects setting ACL
An NFSv4 client that sets an ACL with a named principal during file
creation retrieves the ACL afterwards, and finds that it is only a
default ACL (based on the mode bits) and not the ACL that was
requested during file creation. This violates RFC 8881 section
6.4.1.3: "the ACL attribute is set as given".
The issue occurs in nfsd_create_setattr(), which calls
nfsd_attrs_valid() to determine whether to call nfsd_setattr().
However, nfsd_attrs_valid() checks only for iattr changes and
security labels, but not POSIX ACLs. When only an ACL is present,
the function returns false, nfsd_setattr() is skipped, and the
POSIX ACL is never applied to the inode.
Subsequently, when the client retrieves the ACL, the server finds
no POSIX ACL on the inode and returns one generated from the file's
mode bits rather than returning the originally-specified ACL. |
