| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
spi: ch341: fix out-of-bounds memory access in ch341_transfer_one
Discovered by Atuin - Automated Vulnerability Discovery Engine.
The 'len' variable is calculated as 'min(32, trans->len + 1)',
which includes the 1-byte command header.
When copying data from 'trans->tx_buf' to 'ch341->tx_buf + 1', using 'len'
as the length is incorrect because:
1. It causes an out-of-bounds read from 'trans->tx_buf' (which has size
'trans->len', i.e., 'len - 1' in this context).
2. It can cause an out-of-bounds write to 'ch341->tx_buf' if 'len' is
CH341_PACKET_LENGTH (32). Writing 32 bytes to ch341->tx_buf + 1
overflows the buffer.
Fix this by copying 'len - 1' bytes. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: fix memory leak in bnxt_nvm_test()
Free the kzalloc'ed buffer before returning in the success path. |
| In the Linux kernel, the following vulnerability has been resolved:
hfs: Fix OOB Write in hfs_asc2mac
Syzbot reported a OOB Write bug:
loop0: detected capacity change from 0 to 64
==================================================================
BUG: KASAN: slab-out-of-bounds in hfs_asc2mac+0x467/0x9a0
fs/hfs/trans.c:133
Write of size 1 at addr ffff88801848314e by task syz-executor391/3632
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x1b1/0x28e lib/dump_stack.c:106
print_address_description+0x74/0x340 mm/kasan/report.c:284
print_report+0x107/0x1f0 mm/kasan/report.c:395
kasan_report+0xcd/0x100 mm/kasan/report.c:495
hfs_asc2mac+0x467/0x9a0 fs/hfs/trans.c:133
hfs_cat_build_key+0x92/0x170 fs/hfs/catalog.c:28
hfs_lookup+0x1ab/0x2c0 fs/hfs/dir.c:31
lookup_open fs/namei.c:3391 [inline]
open_last_lookups fs/namei.c:3481 [inline]
path_openat+0x10e6/0x2df0 fs/namei.c:3710
do_filp_open+0x264/0x4f0 fs/namei.c:3740
If in->len is much larger than HFS_NAMELEN(31) which is the maximum
length of an HFS filename, a OOB write could occur in hfs_asc2mac(). In
that case, when the dst reaches the boundary, the srclen is still
greater than 0, which causes a OOB write.
Fix this by adding a check on dstlen in while() before writing to dst
address. |
| In the Linux kernel, the following vulnerability has been resolved:
exfat: fix divide-by-zero in exfat_allocate_bitmap
The variable max_ra_count can be 0 in exfat_allocate_bitmap(),
which causes a divide-by-zero error in the subsequent modulo operation
(i % max_ra_count), leading to a system crash.
When max_ra_count is 0, it means that readahead is not used. This patch
load the bitmap without readahead. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Fix the error "trying to register non-static key in rxe_cleanup_task"
In the function rxe_create_qp(), rxe_qp_from_init() is called to
initialize qp, internally things like rxe_init_task are not setup until
rxe_qp_init_req().
If an error occurred before this point then the unwind will call
rxe_cleanup() and eventually to rxe_qp_do_cleanup()/rxe_cleanup_task()
which will oops when trying to access the uninitialized spinlock.
If rxe_init_task is not executed, rxe_cleanup_task will not be called. |
| In the Linux kernel, the following vulnerability has been resolved:
spmi: Add a check for remove callback when removing a SPMI driver
When removing a SPMI driver, there can be a crash due to NULL pointer
dereference if it does not have a remove callback defined. This is
one such call trace observed when removing the QCOM SPMI PMIC driver:
dump_backtrace.cfi_jt+0x0/0x8
dump_stack_lvl+0xd8/0x16c
panic+0x188/0x498
__cfi_slowpath+0x0/0x214
__cfi_slowpath+0x1dc/0x214
spmi_drv_remove+0x16c/0x1e0
device_release_driver_internal+0x468/0x79c
driver_detach+0x11c/0x1a0
bus_remove_driver+0xc4/0x124
driver_unregister+0x58/0x84
cleanup_module+0x1c/0xc24 [qcom_spmi_pmic]
__do_sys_delete_module+0x3ec/0x53c
__arm64_sys_delete_module+0x18/0x28
el0_svc_common+0xdc/0x294
el0_svc+0x38/0x9c
el0_sync_handler+0x8c/0xf0
el0_sync+0x1b4/0x1c0
If a driver has all its resources allocated through devm_() APIs and
does not need any other explicit cleanup, it would not require a
remove callback to be defined. Hence, add a check for remove callback
presence before calling it when removing a SPMI driver. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: media: tegra-video: fix device_node use after free
At probe time this code path is followed:
* tegra_csi_init
* tegra_csi_channels_alloc
* for_each_child_of_node(node, channel) -- iterates over channels
* automatically gets 'channel'
* tegra_csi_channel_alloc()
* saves into chan->of_node a pointer to the channel OF node
* automatically gets and puts 'channel'
* now the node saved in chan->of_node has refcount 0, can disappear
* tegra_csi_channels_init
* iterates over channels
* tegra_csi_channel_init -- uses chan->of_node
After that, chan->of_node keeps storing the node until the device is
removed.
of_node_get() the node and of_node_put() it during teardown to avoid any
risk. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Fix hard lockup when reading the rx_monitor from debugfs
During I/O and simultaneous cat of /sys/kernel/debug/lpfc/fnX/rx_monitor, a
hard lockup similar to the call trace below may occur.
The spin_lock_bh in lpfc_rx_monitor_report is not protecting from timer
interrupts as expected, so change the strength of the spin lock to _irq.
Kernel panic - not syncing: Hard LOCKUP
CPU: 3 PID: 110402 Comm: cat Kdump: loaded
exception RIP: native_queued_spin_lock_slowpath+91
[IRQ stack]
native_queued_spin_lock_slowpath at ffffffffb814e30b
_raw_spin_lock at ffffffffb89a667a
lpfc_rx_monitor_record at ffffffffc0a73a36 [lpfc]
lpfc_cmf_timer at ffffffffc0abbc67 [lpfc]
__hrtimer_run_queues at ffffffffb8184250
hrtimer_interrupt at ffffffffb8184ab0
smp_apic_timer_interrupt at ffffffffb8a026ba
apic_timer_interrupt at ffffffffb8a01c4f
[End of IRQ stack]
apic_timer_interrupt at ffffffffb8a01c4f
lpfc_rx_monitor_report at ffffffffc0a73c80 [lpfc]
lpfc_rx_monitor_read at ffffffffc0addde1 [lpfc]
full_proxy_read at ffffffffb83e7fc3
vfs_read at ffffffffb833fe71
ksys_read at ffffffffb83402af
do_syscall_64 at ffffffffb800430b
entry_SYSCALL_64_after_hwframe at ffffffffb8a000ad |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: Fix pcluster memleak when its block address is zero
syzkaller reported a memleak:
https://syzkaller.appspot.com/bug?id=62f37ff612f0021641eda5b17f056f1668aa9aed
unreferenced object 0xffff88811009c7f8 (size 136):
...
backtrace:
[<ffffffff821db19b>] z_erofs_do_read_page+0x99b/0x1740
[<ffffffff821dee9e>] z_erofs_readahead+0x24e/0x580
[<ffffffff814bc0d6>] read_pages+0x86/0x3d0
...
syzkaller constructed a case: in z_erofs_register_pcluster(),
ztailpacking = false and map->m_pa = zero. This makes pcl->obj.index be
zero although pcl is not a inline pcluster.
Then following path adds refcount for grp, but the refcount won't be put
because pcl is inline.
z_erofs_readahead()
z_erofs_do_read_page() # for another page
z_erofs_collector_begin()
erofs_find_workgroup()
erofs_workgroup_get()
Since it's illegal for the block address of a non-inlined pcluster to
be zero, add check here to avoid registering the pcluster which would
be leaked. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: fix address removal logic in mptcp_pm_nl_rm_addr
Fix inverted WARN_ON_ONCE condition that prevented normal address
removal counter updates. The current code only executes decrement
logic when the counter is already 0 (abnormal state), while
normal removals (counter > 0) are ignored. |
| In the Linux kernel, the following vulnerability has been resolved:
block: fix memory leak in __blkdev_issue_zero_pages
Move the fatal signal check before bio_alloc() to prevent a memory
leak when BLKDEV_ZERO_KILLABLE is set and a fatal signal is pending.
Previously, the bio was allocated before checking for a fatal signal.
If a signal was pending, the code would break out of the loop without
freeing or chaining the just-allocated bio, causing a memory leak.
This matches the pattern already used in __blkdev_issue_write_zeroes()
where the signal check precedes the allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: fix livelock in synchronous file put from fuseblk workers
I observed a hang when running generic/323 against a fuseblk server.
This test opens a file, initiates a lot of AIO writes to that file
descriptor, and closes the file descriptor before the writes complete.
Unsurprisingly, the AIO exerciser threads are mostly stuck waiting for
responses from the fuseblk server:
# cat /proc/372265/task/372313/stack
[<0>] request_wait_answer+0x1fe/0x2a0 [fuse]
[<0>] __fuse_simple_request+0xd3/0x2b0 [fuse]
[<0>] fuse_do_getattr+0xfc/0x1f0 [fuse]
[<0>] fuse_file_read_iter+0xbe/0x1c0 [fuse]
[<0>] aio_read+0x130/0x1e0
[<0>] io_submit_one+0x542/0x860
[<0>] __x64_sys_io_submit+0x98/0x1a0
[<0>] do_syscall_64+0x37/0xf0
[<0>] entry_SYSCALL_64_after_hwframe+0x4b/0x53
But the /weird/ part is that the fuseblk server threads are waiting for
responses from itself:
# cat /proc/372210/task/372232/stack
[<0>] request_wait_answer+0x1fe/0x2a0 [fuse]
[<0>] __fuse_simple_request+0xd3/0x2b0 [fuse]
[<0>] fuse_file_put+0x9a/0xd0 [fuse]
[<0>] fuse_release+0x36/0x50 [fuse]
[<0>] __fput+0xec/0x2b0
[<0>] task_work_run+0x55/0x90
[<0>] syscall_exit_to_user_mode+0xe9/0x100
[<0>] do_syscall_64+0x43/0xf0
[<0>] entry_SYSCALL_64_after_hwframe+0x4b/0x53
The fuseblk server is fuse2fs so there's nothing all that exciting in
the server itself. So why is the fuse server calling fuse_file_put?
The commit message for the fstest sheds some light on that:
"By closing the file descriptor before calling io_destroy, you pretty
much guarantee that the last put on the ioctx will be done in interrupt
context (during I/O completion).
Aha. AIO fgets a new struct file from the fd when it queues the ioctx.
The completion of the FUSE_WRITE command from userspace causes the fuse
server to call the AIO completion function. The completion puts the
struct file, queuing a delayed fput to the fuse server task. When the
fuse server task returns to userspace, it has to run the delayed fput,
which in the case of a fuseblk server, it does synchronously.
Sending the FUSE_RELEASE command sychronously from fuse server threads
is a bad idea because a client program can initiate enough simultaneous
AIOs such that all the fuse server threads end up in delayed_fput, and
now there aren't any threads left to handle the queued fuse commands.
Fix this by only using asynchronous fputs when closing files, and leave
a comment explaining why. |
| In the Linux kernel, the following vulnerability has been resolved:
media: imx-jpeg: Disable useless interrupt to avoid kernel panic
There is a hardware bug that the interrupt STMBUF_HALF may be triggered
after or when disable interrupt.
It may led to unexpected kernel panic.
And interrupt STMBUF_HALF and STMBUF_RTND have no other effect.
So disable them and the unused interrupts.
meanwhile clear the interrupt status when disable interrupt. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: prevent poison consumption when splitting THP
When performing memory error injection on a THP (Transparent Huge Page)
mapped to userspace on an x86 server, the kernel panics with the following
trace. The expected behavior is to terminate the affected process instead
of panicking the kernel, as the x86 Machine Check code can recover from an
in-userspace #MC.
mce: [Hardware Error]: CPU 0: Machine Check Exception: f Bank 3: bd80000000070134
mce: [Hardware Error]: RIP 10:<ffffffff8372f8bc> {memchr_inv+0x4c/0xf0}
mce: [Hardware Error]: TSC afff7bbff88a ADDR 1d301b000 MISC 80 PPIN 1e741e77539027db
mce: [Hardware Error]: PROCESSOR 0:d06d0 TIME 1758093249 SOCKET 0 APIC 0 microcode 80000320
mce: [Hardware Error]: Run the above through 'mcelog --ascii'
mce: [Hardware Error]: Machine check: Data load in unrecoverable area of kernel
Kernel panic - not syncing: Fatal local machine check
The root cause of this panic is that handling a memory failure triggered
by an in-userspace #MC necessitates splitting the THP. The splitting
process employs a mechanism, implemented in
try_to_map_unused_to_zeropage(), which reads the pages in the THP to
identify zero-filled pages. However, reading the pages in the THP results
in a second in-kernel #MC, occurring before the initial memory_failure()
completes, ultimately leading to a kernel panic. See the kernel panic
call trace on the two #MCs.
First Machine Check occurs // [1]
memory_failure() // [2]
try_to_split_thp_page()
split_huge_page()
split_huge_page_to_list_to_order()
__folio_split() // [3]
remap_page()
remove_migration_ptes()
remove_migration_pte()
try_to_map_unused_to_zeropage() // [4]
memchr_inv() // [5]
Second Machine Check occurs // [6]
Kernel panic
[1] Triggered by accessing a hardware-poisoned THP in userspace, which is
typically recoverable by terminating the affected process.
[2] Call folio_set_has_hwpoisoned() before try_to_split_thp_page().
[3] Pass the RMP_USE_SHARED_ZEROPAGE remap flag to remap_page().
[4] Try to map the unused THP to zeropage.
[5] Re-access pages in the hw-poisoned THP in the kernel.
[6] Triggered in-kernel, leading to a panic kernel.
In Step[2], memory_failure() sets the poisoned flag on the page in the THP
by TestSetPageHWPoison() before calling try_to_split_thp_page().
As suggested by David Hildenbrand, fix this panic by not accessing to the
poisoned page in the THP during zeropage identification, while continuing
to scan unaffected pages in the THP for possible zeropage mapping. This
prevents a second in-kernel #MC that would cause kernel panic in Step[4].
Thanks to Andrew Zaborowski for his initial work on fixing this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: hif_usb: fix memory leak of urbs in ath9k_hif_usb_dealloc_tx_urbs()
Syzkaller reports a long-known leak of urbs in
ath9k_hif_usb_dealloc_tx_urbs().
The cause of the leak is that usb_get_urb() is called but usb_free_urb()
(or usb_put_urb()) is not called inside usb_kill_urb() as urb->dev or
urb->ep fields have not been initialized and usb_kill_urb() returns
immediately.
The patch removes trying to kill urbs located in hif_dev->tx.tx_buf
because hif_dev->tx.tx_buf is not supposed to contain urbs which are in
pending state (the pending urbs are stored in hif_dev->tx.tx_pending).
The tx.tx_lock is acquired so there should not be any changes in the list.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
netrom: Fix memory leak in nr_sendmsg()
syzbot reported a memory leak [1].
When function sock_alloc_send_skb() return NULL in nr_output(), the
original skb is not freed, which was allocated in nr_sendmsg(). Fix this
by freeing it before return.
[1]
BUG: memory leak
unreferenced object 0xffff888129f35500 (size 240):
comm "syz.0.17", pid 6119, jiffies 4294944652
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 10 52 28 81 88 ff ff ..........R(....
backtrace (crc 1456a3e4):
kmemleak_alloc_recursive include/linux/kmemleak.h:44 [inline]
slab_post_alloc_hook mm/slub.c:4983 [inline]
slab_alloc_node mm/slub.c:5288 [inline]
kmem_cache_alloc_node_noprof+0x36f/0x5e0 mm/slub.c:5340
__alloc_skb+0x203/0x240 net/core/skbuff.c:660
alloc_skb include/linux/skbuff.h:1383 [inline]
alloc_skb_with_frags+0x69/0x3f0 net/core/skbuff.c:6671
sock_alloc_send_pskb+0x379/0x3e0 net/core/sock.c:2965
sock_alloc_send_skb include/net/sock.h:1859 [inline]
nr_sendmsg+0x287/0x450 net/netrom/af_netrom.c:1105
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg net/socket.c:742 [inline]
sock_write_iter+0x293/0x2a0 net/socket.c:1195
new_sync_write fs/read_write.c:593 [inline]
vfs_write+0x45d/0x710 fs/read_write.c:686
ksys_write+0x143/0x170 fs/read_write.c:738
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xa4/0xfa0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f |
| In the Linux kernel, the following vulnerability has been resolved:
ethtool: Avoid overflowing userspace buffer on stats query
The ethtool -S command operates across three ioctl calls:
ETHTOOL_GSSET_INFO for the size, ETHTOOL_GSTRINGS for the names, and
ETHTOOL_GSTATS for the values.
If the number of stats changes between these calls (e.g., due to device
reconfiguration), userspace's buffer allocation will be incorrect,
potentially leading to buffer overflow.
Drivers are generally expected to maintain stable stat counts, but some
drivers (e.g., mlx5, bnx2x, bna, ksz884x) use dynamic counters, making
this scenario possible.
Some drivers try to handle this internally:
- bnad_get_ethtool_stats() returns early in case stats.n_stats is not
equal to the driver's stats count.
- micrel/ksz884x also makes sure not to write anything beyond
stats.n_stats and overflow the buffer.
However, both use stats.n_stats which is already assigned with the value
returned from get_sset_count(), hence won't solve the issue described
here.
Change ethtool_get_strings(), ethtool_get_stats(),
ethtool_get_phy_stats() to not return anything in case of a mismatch
between userspace's size and get_sset_size(), to prevent buffer
overflow.
The returned n_stats value will be equal to zero, to reflect that
nothing has been returned.
This could result in one of two cases when using upstream ethtool,
depending on when the size change is detected:
1. When detected in ethtool_get_strings():
# ethtool -S eth2
no stats available
2. When detected in get stats, all stats will be reported as zero.
Both cases are presumably transient, and a subsequent ethtool call
should succeed.
Other than the overflow avoidance, these two cases are very evident (no
output/cleared stats), which is arguably better than presenting
incorrect/shifted stats.
I also considered returning an error instead of a "silent" response, but
that seems more destructive towards userspace apps.
Notes:
- This patch does not claim to fix the inherent race, it only makes sure
that we do not overflow the userspace buffer, and makes for a more
predictable behavior.
- RTNL lock is held during each ioctl, the race window exists between
the separate ioctl calls when the lock is released.
- Userspace ethtool always fills stats.n_stats, but it is likely that
these stats ioctls are implemented in other userspace applications
which might not fill it. The added code checks that it's not zero,
to prevent any regressions. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: hda: cs35l41: Fix NULL pointer dereference in cs35l41_hda_read_acpi()
The acpi_get_first_physical_node() function can return NULL, in which
case the get_device() function also returns NULL, but this value is
then dereferenced without checking,so add a check to prevent a crash.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: Add null pointer check for inode operations
This adds a sanity check for the i_op pointer of the inode which is
returned after reading Root directory MFT record. We should check the
i_op is valid before trying to create the root dentry, otherwise we may
encounter a NPD while mounting a image with a funny Root directory MFT
record.
[ 114.484325] BUG: kernel NULL pointer dereference, address: 0000000000000008
[ 114.484811] #PF: supervisor read access in kernel mode
[ 114.485084] #PF: error_code(0x0000) - not-present page
[ 114.485606] PGD 0 P4D 0
[ 114.485975] Oops: 0000 [#1] PREEMPT SMP KASAN NOPTI
[ 114.486570] CPU: 0 PID: 237 Comm: mount Tainted: G B 6.0.0-rc4 #28
[ 114.486977] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[ 114.488169] RIP: 0010:d_flags_for_inode+0xe0/0x110
[ 114.488816] Code: 24 f7 ff 49 83 3e 00 74 41 41 83 cd 02 66 44 89 6b 02 eb 92 48 8d 7b 20 e8 6d 24 f7 ff 4c 8b 73 20 49 8d 7e 08 e8 60 241
[ 114.490326] RSP: 0018:ffff8880065e7aa8 EFLAGS: 00000296
[ 114.490695] RAX: 0000000000000001 RBX: ffff888008ccd750 RCX: ffffffff84af2aea
[ 114.490986] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffffffff87abd020
[ 114.491364] RBP: ffff8880065e7ac8 R08: 0000000000000001 R09: fffffbfff0f57a05
[ 114.491675] R10: ffffffff87abd027 R11: fffffbfff0f57a04 R12: 0000000000000000
[ 114.491954] R13: 0000000000000008 R14: 0000000000000000 R15: ffff888008ccd750
[ 114.492397] FS: 00007fdc8a627e40(0000) GS:ffff888058200000(0000) knlGS:0000000000000000
[ 114.492797] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 114.493150] CR2: 0000000000000008 CR3: 00000000013ba000 CR4: 00000000000006f0
[ 114.493671] Call Trace:
[ 114.493890] <TASK>
[ 114.494075] __d_instantiate+0x24/0x1c0
[ 114.494505] d_instantiate.part.0+0x35/0x50
[ 114.494754] d_make_root+0x53/0x80
[ 114.494998] ntfs_fill_super+0x1232/0x1b50
[ 114.495260] ? put_ntfs+0x1d0/0x1d0
[ 114.495499] ? vsprintf+0x20/0x20
[ 114.495723] ? set_blocksize+0x95/0x150
[ 114.495964] get_tree_bdev+0x232/0x370
[ 114.496272] ? put_ntfs+0x1d0/0x1d0
[ 114.496502] ntfs_fs_get_tree+0x15/0x20
[ 114.496859] vfs_get_tree+0x4c/0x130
[ 114.497099] path_mount+0x654/0xfe0
[ 114.497507] ? putname+0x80/0xa0
[ 114.497933] ? finish_automount+0x2e0/0x2e0
[ 114.498362] ? putname+0x80/0xa0
[ 114.498571] ? kmem_cache_free+0x1c4/0x440
[ 114.498819] ? putname+0x80/0xa0
[ 114.499069] do_mount+0xd6/0xf0
[ 114.499343] ? path_mount+0xfe0/0xfe0
[ 114.499683] ? __kasan_check_write+0x14/0x20
[ 114.500133] __x64_sys_mount+0xca/0x110
[ 114.500592] do_syscall_64+0x3b/0x90
[ 114.500930] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 114.501294] RIP: 0033:0x7fdc898e948a
[ 114.501542] Code: 48 8b 0d 11 fa 2a 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 008
[ 114.502716] RSP: 002b:00007ffd793e58f8 EFLAGS: 00000202 ORIG_RAX: 00000000000000a5
[ 114.503175] RAX: ffffffffffffffda RBX: 0000564b2228f060 RCX: 00007fdc898e948a
[ 114.503588] RDX: 0000564b2228f260 RSI: 0000564b2228f2e0 RDI: 0000564b22297ce0
[ 114.504925] RBP: 0000000000000000 R08: 0000564b2228f280 R09: 0000000000000020
[ 114.505484] R10: 00000000c0ed0000 R11: 0000000000000202 R12: 0000564b22297ce0
[ 114.505823] R13: 0000564b2228f260 R14: 0000000000000000 R15: 00000000ffffffff
[ 114.506562] </TASK>
[ 114.506887] Modules linked in:
[ 114.507648] CR2: 0000000000000008
[ 114.508884] ---[ end trace 0000000000000000 ]---
[ 114.509675] RIP: 0010:d_flags_for_inode+0xe0/0x110
[ 114.510140] Code: 24 f7 ff 49 83 3e 00 74 41 41 83 cd 02 66 44 89 6b 02 eb 92 48 8d 7b 20 e8 6d 24 f7 ff 4c 8b 73 20 49 8d 7e 08 e8 60 241
[ 114.511762] RSP: 0018:ffff8880065e7aa8 EFLAGS: 00000296
[ 114.512401] RAX: 0000000000000001 RBX: ffff888008ccd750 RCX: ffffffff84af2aea
[ 114.51
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/guc: Fix stack_depot usage
Add missing stack_depot_init() call when CONFIG_DRM_XE_DEBUG_GUC is
enabled to fix the following call stack:
[] BUG: kernel NULL pointer dereference, address: 0000000000000000
[] Workqueue: drm_sched_run_job_work [gpu_sched]
[] RIP: 0010:stack_depot_save_flags+0x172/0x870
[] Call Trace:
[] <TASK>
[] fast_req_track+0x58/0xb0 [xe]
(cherry picked from commit 64fdf496a6929a0a194387d2bb5efaf5da2b542f) |
