| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: reset the LED state when ifup fails
When the first interface comes up, the radio LED is turned on. This can
start the TPT trigger timer, which continues running.
But if bringing up the interface fails then the timer keeps running and
won't be stopped by anything, eventually it can be freed:
ODEBUG: free active (active state 0) object: ffff888127e12130 object type: timer_list hint: tpt_trig_timer+0x0/0x300 net/mac80211/led.c:145
WARNING: CPU: 0 PID: 5923 at lib/debugobjects.c:612 debug_print_object+0x1a2/0x2b0
debug_check_no_obj_freed+0x4b7/0x600 lib/debugobjects.c:1129
kfree+0x436/0x670 mm/slub.c:6818
ieee80211_led_exit+0x162/0x1c0 net/mac80211/led.c:210
ieee80211_unregister_hw+0x27e/0x3a0 net/mac80211/main.c:1706
rt2x00lib_remove_dev+0x55b/0x670
Undo the LED state in the error path. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: reset state when starting AP fails
ieee80211_start_ap() can set enable_beacon (and beacon_int) and fail
later, leaving it set forever. Scanning can then attempt to restore
beaconing on such an interface, leading to:
Oops: divide error: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:mac80211_hwsim_link_info_changed+0xca7/0xf00
Call Trace:
drv_link_info_changed+0x413/0x860 net/mac80211/driver-ops.c:495
ieee80211_link_info_change_notify+0x24b/0x3c0 net/mac80211/main.c:427
ieee80211_offchannel_return+0x381/0x580 net/mac80211/offchannel.c:160
__ieee80211_scan_completed+0x993/0xe30 net/mac80211/scan.c:519
ieee80211_scan_work+0x472/0x2010 net/mac80211/scan.c:1193
cfg80211_wiphy_work+0x2b7/0x550 net/wireless/core.c:538
in hwsim. Also, cfg80211 then allows changing the interface type,
and the off-channel path getgs confused about beaconing as well,
leading to another warning:
WARNING: net/mac80211/driver-ops.c:468 at drv_link_info_changed+0x583/0x880
ieee80211_link_info_change_notify+0x24b/0x3c0 net/mac80211/main.c:427
ieee80211_offchannel_stop_vifs+0x328/0x5c0 net/mac80211/offchannel.c:122
ieee80211_start_sw_scan net/mac80211/scan.c:583 [inline]
__ieee80211_start_scan+0xfb6/0x1af0 net/mac80211/scan.c:882
Reset the state on failures to always have it correct. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: wait for RCU readers before releasing dma_device
dma_issue_pending_all() walks the dma_device_list with
list_for_each_entry_rcu() under rcu_read_lock(). dma_device_release()
unlinks the device with list_del_rcu() and then calls
device->device_release() (which in many drivers, such as plx_dma.c,
directly calls kfree()).
Because there is no grace period between unlinking the device and
freeing it, concurrent RCU readers in dma_issue_pending_all() can
access the device after it has been freed.
The lockless walk originally relied on clients holding a dmaengine
reference to pin the provider module, and therefore the device, for as
long as they might traverse the list. Commit 8ad342a86359 ("dmaengine:
Add reference counting to dma_device struct") decoupled the dma_device
lifetime from the module reference, so the device can now be released
while a reader is still walking the list.
Add synchronize_rcu() before the device is freed, so RCU readers are
guaranteed to have finished. Keep it unconditional: providers that do
not implement device_release() free the device themselves once
dma_async_device_unregister() returns. This call will delay for a grace
period with dma_list_mutex held, which is safe and only teardown path is
delayed. |
| Confused deputy in UI in Google Chrome on on Android prior to 155.0.8059.39 allowed a local attacker to bypass system access restrictions into a privileged page via a co-installed app. (Chromium security severity: Medium) |
| Improper resource exposure in Extensions in Google Chrome prior to 155.0.8059.39 allowed a remote attacker to obtain cross-origin data via a crafted HTML page. (Chromium security severity: Medium) |
| Information leak in Autofill in Google Chrome prior to 155.0.8059.39 allowed a remote attacker to obtain sensitive information via a crafted HTML page. (Chromium security severity: Medium) |
| Code injection in Extensions in Google Chrome prior to 155.0.8059.39 allowed a remote attacker leveraging social engineering to spoof UI elements via a crafted Chrome extension. (Chromium security severity: Medium) |
| Incorrect authorization in PermissionElement in Google Chrome prior to 155.0.8059.39 allowed a remote attacker to potentially bypass web origin policy via a crafted HTML page. (Chromium security severity: Medium) |
| Incorrect authorization in Input in Google Chrome prior to 155.0.8059.39 allowed a remote attacker leveraging social engineering to spoof UI elements via a crafted HTML page. (Chromium security severity: Medium) |
| UI misrepresentation in FileSystem in Google Chrome prior to 155.0.8059.39 allowed a remote attacker leveraging social engineering to bypass system access restrictions via a crafted HTML page. (Chromium security severity: Medium) |
| Observable discrepancy in Paint in Google Chrome prior to 155.0.8059.39 allowed a remote attacker to leak cross-origin data via a crafted HTML page. (Chromium security severity: Medium) |
| Incorrect authorization in Accessibility in Google Chrome prior to 155.0.8059.39 allowed a remote attacker who had compromised the renderer process to bypass site isolation via a crafted HTML page. (Chromium security severity: Medium) |
| When password or public key authentication is used with the Windows port of wolfSSHd, the Windows logon token acquired for one authenticated connection is not released before a token is acquired for a subsequent connection, resulting in user login poisoning between connections. A less privileged user with a valid account on the server can exploit this to force a login as a more privileged user. The vulnerability was introduced with the initial Windows port of wolfSSHd in wolfSSH version 1.4.15 and affects all versions through 1.5.0. Non-Windows builds of wolfSSHd are not affected. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: abort transaction on failure to update inode for hole punching and reflinking
If we fail to update the inode we error out without aborting the
transaction, which can result in a persistent inconsistency if after
the failure the transaction is committed, as we have dropped file
extent items from a range and either punched a hole or insert a new file
extent item for that range (for reflinks).
So add the missing transaction abort. |
| In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: fix TSO header length truncation
stmmac_tso_xmit() stores the protocol header length returned by
stmmac_tso_header_size() in a u8. stmmac_tso_valid_packet() admits
headers up to 1023 bytes, so a header longer than 255 bytes wraps modulo
256 (486 becomes 230, 256 becomes 0).
A TCP over IPv6 socket carrying a few hundred bytes of sticky
destination/hop-by-hop options makes skb_tcp_all_headers() exceed 255
while staying below the 1023-byte limit, so such an skb reaches
stmmac_tso_xmit().
Widen proto_hdr_len to unsigned int, which is sufficient since the value
is bounded by the hardware limit, and adjust the debug print specifier
accordingly. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btmtksdio, btmtkuart: validate WMT event length before struct access
btmtksdio.c and btmtkuart.c cast a received WMT event straight to
struct btmtk_hci_wmt_evt and read its op/flag fields without checking
the event is long enough to contain them, unlike btmtk.c. The
FUNC_CTRL case then further casts to struct btmtk_hci_wmt_evt_funcc
and reads its 2-byte status field, again without a length check.
Firmware that sends a short or malformed WMT event makes both drivers
read past the end of the received SKB.
Mirror btmtk.c: validate the base WMT header with skb_pull_data()
before touching any of its fields, and when a FUNC_CTRL event turns
out to be the short, header-only form (a plain enable/disable ack
with no status word), decode the result from the header's own flag
byte instead (0 = success, otherwise failure).
Verified setup on MT7920, MT7921, MT7922 and MT7925: no regression. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: Fix parent socket leak in iso_conn_ready()
iso_get_sock() returns the parent socket with a reference held, which is
dropped by sock_put() once the child socket has been set up. The error
path taken when iso_sock_alloc() fails only calls release_sock() and
returns, leaking the reference and thus the parent socket itself.
Drop the reference on that path as well. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: fix use-after-free in dma_chan_put() and dma_release_channel()
When dma_device_put() drops the last reference on chan->device->ref,
dma_device_release() runs and may free the dma_device along with its
channels.
dma_chan_put() then still reads chan->device->owner via
dma_chan_to_owner() for the trailing module_put(). KASAN catches it:
slab-use-after-free in dma_chan_put+0x3e6/0x4c0
Read of size 8 by task insmod/6319
Freed by task 6319:
kfree+0x225/0x470
dma_chan_put+0x395/0x4c0
dmaengine_put+0xf8/0x160
Cache the module owner in dma_chan_put() before the put so the trailing
module_put() does not need chan->device. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rtrs: guard against null kobj name
In the client, if `init_path()` errors, the callee tries to clean up
with `rtrs_clt_close_conns()`. However, this can lead to calling the
event tracing code with `clt_path->kobj->name` being `NULL` and thus
causing a null pointer dereference when trying to copy from it.
This just adds a guard to check that the name is not `NULL` before
copying from it. The server appears to have a similar pattern. |
| In the Linux kernel, the following vulnerability has been resolved:
IB/iser: reject a remote invalidation of an unregistered direction
A write command whose data is sent entirely as immediate data is not
registered. iser_reg_mem_fastreg() takes the DMA key path and leaves
rdma_reg[ISER_DIR_OUT].desc at NULL, while iser_dma_map_task_data() has
already set dir[ISER_DIR_OUT].
iser_check_remote_inv() looks at dir[] alone and hands the descriptor to
iser_inv_desc(), which reads desc->sig_protected. A target that answers
such a command with IB_WR_SEND_WITH_INV faults the initiator.
Leaving those commands unregistered is deliberate.
The same function already terminates the connection when a target sends
a remote invalidation the initiator did not ask for. A target that
invalidates a direction that was never registered is in the same class,
so give it the same answer.
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000004: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000020-0x0000000000000027]
CPU: 0 UID: 0 PID: 40 Comm: kworker/u8:2 Not tainted 7.2.0-rc5-ISERHOST-gf5098b6bae76-dirty #3 PREEMPT(lazy)
Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Workqueue: rxe_wq do_work
RIP: 0010:iser_task_rsp+0x6d6/0xec0
Code: 48 c1 ea 03 80 3c 02 00 0f 85 ba 06 00 00 48 8b 9b 78 01 00 00 48 b8 00 00 00 00 00 fc ff df 48 8d 7b 20 48 89 fa 48 c1 ea 03 <0f> b6 04 02 84 c0 74 06 0f 8e 76 06 00 00 80 7b 20 00 0f 84 3d 04
RSP: 0018:ffff88811b008db8 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000001848
RDX: 0000000000000004 RSI: 1ffff11021587b12 RDI: 0000000000000020
RBP: ffff88810adc1ae4 R08: ffff888109b7f860 R09: ffffffff90a922c0
R10: ffff88810adc1a1c R11: 000000000000003c R12: ffff888109b7f800
R13: ffff88810adc1acc R14: ffff888109b7f820 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88818a676000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000005afe2b CR3: 000000010af23005 CR4: 0000000000770ef0
PKRU: 55555554
Call Trace:
<IRQ>
__ib_process_cq+0xe1/0x390
ib_poll_handler+0x6e/0x200
irq_poll_softirq+0x1df/0x480
? clockevents_program_event+0x2ba/0x860
? __pfx_irq_poll_softirq+0x10/0x10
handle_softirqs+0x18e/0x590
? __pfx_handle_softirqs+0x10/0x10
? __hrtimer_rearm_deferred+0x156/0x450
do_softirq+0x3b/0x60
</IRQ>
<TASK>
__local_bh_enable_ip+0x61/0x70
__alloc_skb+0x732/0x890
? _raw_spin_lock_irqsave+0x85/0xe0
? __pfx___alloc_skb+0x10/0x10
? _raw_read_unlock_irqrestore+0x16/0x50
rxe_init_packet+0x16b/0x4f0
prepare_ack_packet+0xb8/0x830
rxe_receiver+0x499/0x9980
? __pfx_rxe_receiver+0x10/0x10
? rxe_completer+0x29e5/0x38c0
? hrtimer_start_range_ns_common+0x75f/0x1730
? hrtimer_start_range_ns+0xa6/0x2c0
? __pfx__raw_spin_lock_irqsave+0x10/0x10
? __pfx_rxe_receiver+0x10/0x10
do_work+0x144/0x470
process_one_work+0x633/0x1030
? assign_work+0x11d/0x370
worker_thread+0x45b/0xd10
? __pfx_worker_thread+0x10/0x10
kthread+0x2c6/0x3b0
? recalc_sigpending+0x15c/0x1e0
? __pfx_kthread+0x10/0x10
ret_from_fork+0x36e/0x5a0
? __pfx_ret_from_fork+0x10/0x10
? __switch_to+0x572/0xdd0
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
Modules linked in:
---[ end trace 0000000000000000 ]--- |
