| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In Netgear WNR854T 1.5.2 (North America), the UPNP service is vulnerable to command injection in the function addmap_exec which parses the NewInternalClient parameter of the AddPortMapping SOAPAction into a system call without sanitation. An attacker can send a specially crafted SOAPAction request for AddPortMapping via the router's WANIPConn1 service to achieve arbitrary command execution. |
| Netgear WNR854T 1.5.2 (North America) contains a stack-based buffer overflow vulnerability in the SetDefaultConnectionService function due to an unconstrained use of sscanf. The vulnerability allows for control of the program counter and can be utilized to achieve arbitrary code execution. |
| Netgear Inc WNR854T 1.5.2 (North America) contains a stack-based buffer overflow vulnerability in the parse_st_header function due to use of a request header parameter in a strncpy where size is determined based on the input specified. By sending a specially crafted packet, an attacker can take control of the program counter and hijack control flow of the program to execute arbitrary system commands. |
| An exploitable firmware modification vulnerability was discovered on the Netgear XWN5001 Powerline 500 WiFi Access Point. An attacker can conduct a MITM (Man-in-the-Middle) attack to modify the user-uploaded firmware image and bypass the CRC check, allowing attackers to execute arbitrary code or cause a Denial of Service (DoS). This affects v0.4.1.1 and earlier. |
| A network misconfiguration is present in versions prior to 1.0.9.90 of the NETGEAR RAX30 AX2400 series of routers. IPv6 is enabled for the WAN interface by default on these devices. While there are firewall restrictions in place that define access restrictions for IPv4 traffic, these restrictions do not appear to be applied to the WAN interface for IPv6. This allows arbitrary access to any services running on the device that may be inadvertently listening via IPv6, such as the SSH and Telnet servers spawned on ports 22 and 23 by default. This misconfiguration could allow an attacker to interact with services only intended to be accessible by clients on the local network. |
| handle_daylightsaving.php in NUUO NVRmini 2 1.7.5 through 3.0.0, NUUO NVRsolo 1.0.0 through 3.0.0, NUUO Crystal 2.2.1 through 3.2.0, and NETGEAR ReadyNAS Surveillance 1.1.1 through 1.4.1 allows remote attackers to execute arbitrary PHP code via the NTPServer parameter. |
| The IKEv2 implementation in Cisco IOS 15.0 through 15.6 and IOS XE 3.3 through 3.17 allows remote attackers to cause a denial of service (device reload) via fragmented packets, aka Bug ID CSCux38417. |
| The password-recovery feature on NETGEAR D3600 devices with firmware 1.0.0.49 and D6000 devices with firmware 1.0.0.49 and earlier allows remote attackers to discover the cleartext administrator password by reading the cgi-bin/passrec.asp HTML source code. |
| NETGEAR D3600 devices with firmware 1.0.0.49 and D6000 devices with firmware 1.0.0.49 and earlier use the same hardcoded private key across different customers' installations, which allows remote attackers to defeat cryptographic protection mechanisms by leveraging knowledge of this key from another installation. |
| Directory traversal vulnerability in data/config/image.do in NETGEAR Management System NMS300 1.5.0.11 and earlier allows remote authenticated users to read arbitrary files via a .. (dot dot) in the realName parameter. |
| The Smart Install client implementation in Cisco IOS 12.2, 15.0, and 15.2 and IOS XE 3.2 through 3.7 allows remote attackers to cause a denial of service (device reload) via crafted image list parameters in a Smart Install packet, aka Bug ID CSCuv45410. |
| cgi-bin/cgi_main in NUUO NVRmini 2 1.7.6 through 3.0.0 and NETGEAR ReadyNAS Surveillance 1.1.2 allows remote authenticated users to execute arbitrary commands via shell metacharacters in the sn parameter to the transfer_license command. |
| Cisco IOS 15.0 through 15.5 and IOS XE 3.3 through 3.16 allow remote attackers to cause a denial of service (device reload) via a crafted DHCPv6 Relay message, aka Bug ID CSCus55821. |
| __debugging_center_utils___.php in NUUO NVRmini 2 1.7.5 through 3.0.0, NUUO NVRsolo 1.7.5 through 3.0.0, and NETGEAR ReadyNAS Surveillance 1.1.1 through 1.4.1 allows remote attackers to execute arbitrary PHP code via the log parameter. |
| NETGEAR Arlo base stations with firmware 1.7.5_6178 and earlier, Arlo Q devices with firmware 1.8.0_5551 and earlier, and Arlo Q Plus devices with firmware 1.8.1_6094 and earlier have a default password of 12345678, which makes it easier for remote attackers to obtain access after a factory reset or in a factory configuration. |
| Cisco TelePresence Server 3.1 on 7010, Mobility Services Engine (MSE) 8710, Multiparty Media 310 and 320, and Virtual Machine (VM) devices allows remote attackers to cause a denial of service (device reload) via malformed STUN packets, aka Bug ID CSCuv01348. |
| Cisco NX-OS 4.0 through 6.1 on Nexus 1000V 3000, 4000, 5000, 6000, and 7000 devices and Unified Computing System (UCS) platforms allows remote attackers to cause a denial of service (TCP stack reload) by sending crafted TCP packets to a device that has a TIME_WAIT TCP session, aka Bug ID CSCub70579. |
| NETGEAR Arlo base stations with firmware 1.7.5_6178 and earlier, Arlo Q devices with firmware 1.8.0_5551 and earlier, and Arlo Q Plus devices with firmware 1.8.1_6094 and earlier use a pattern of adjective, noun, and three-digit number for the customized password, which makes it easier for remote attackers to obtain access via a dictionary attack. |
| Directory traversal vulnerability in scgi-bin/platform.cgi on NETGEAR FVS336Gv3, FVS318N, FVS318Gv2, and SRX5308 devices with firmware before 4.3.3-8 allows remote authenticated users to read arbitrary files via a .. (dot dot) in the thispage parameter, as demonstrated by reading the /etc/shadow file. |
| NETGEAR GS108PE Prosafe Plus switches with firmware 1.2.0.5 have a hardcoded password of debugpassword for the ntgruser account, which allows remote attackers to upload firmware or read or modify memory contents, and consequently execute arbitrary code, via a request to (1) produce_burn.cgi, (2) register_debug.cgi, or (3) bootcode_update.cgi. |
