| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net/packet: avoid fanout hook re-registration after unregister
packet_set_ring() temporarily detaches a socket from packet delivery while
reconfiguring its ring. It records the previous running state, clears
po->num, unregisters the protocol hook when needed, drops po->bind_lock,
and later restores po->num and re-registers the hook from the saved
was_running value.
That unlocked window can race with NETDEV_UNREGISTER. The notifier can
observe the socket as not running, skip __unregister_prot_hook(), and
invalidate the per-socket binding by setting po->ifindex to -1 and clearing
po->prot_hook.dev. A one-member fanout group can still retain its shared
fanout hook device pointer. When packet_set_ring() resumes, re-registering
solely from the stale was_running state can re-add the fanout hook after
the device has been unregistered.
Treat po->ifindex == -1 as an invalidated binding after reacquiring
po->bind_lock. This is distinct from ifindex 0, the normal
unbound/wildcard state: ifindex -1 marks an existing device binding that
was invalidated when the device was unregistered. Restore po->num as
before, but do not re-register the hook if device unregister already
detached the socket. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: occ: validate poll response sensor blocks
The OCC poll response parser walks a counted list of sensor data blocks.
It used the static backing-array capacity as the parse boundary, but a
transport response makes only data_length bytes current and valid. A
truncated response can therefore make the parser consume a block header or
block extent outside the current response.
Use data_length as the parent boundary, prove the fixed poll header and
each current block header before reading them, and prove the complete block
before advancing. Keep parsed sensor metadata local until the complete
response has passed validation, then publish it. Propagate
malformed-response errors before publishing the OCC as active. |
| In the Linux kernel, the following vulnerability has been resolved:
ovpn: fix use after free in unlock_ovpn()
unlock_ovpn() iterates over the release_list using llist_for_each_entry()
and drops the peer reference inside the loop body via ovpn_peer_put().
If this drops the last reference, the peer is eventually freed. However,
llist_for_each_entry() reads peer->release_entry.next in the loop advance
expression, which runs after the body. By that time the peer may have
already been freed, resulting in a use after free when advancing to the
next list entry.
Fix this by using llist_for_each_entry_safe(), which caches the next
pointer before executing the loop body. |
| In the Linux kernel, the following vulnerability has been resolved:
ovpn: avoid putting unrelated P2P peer on socket release
ovpn_peer_release_p2p() is called when an OVPN UDP socket is being
destroyed. It checks the currently published P2P peer and releases it only
if that peer still uses the socket being destroyed.
A peer replacement can publish a new peer before the old UDP socket is
destroyed. When the old socket destruction path runs afterwards,
ovpn_peer_release_p2p() observes the new peer through ovpn->peer. Since the
new peer uses a different socket, the function takes the socket mismatch
branch.
That branch still calls ovpn_peer_put(peer). At this point, however, peer
is the currently published replacement peer, not the peer associated with
the socket being destroyed. Dropping its reference can free it while
ovpn->peer still points to it, leading to later use-after-free accesses
from the peer and socket cleanup paths.
KASAN reports this as a slab-use-after-free on the kmalloc-1k ovpn_peer
object. In the reproducer, the object is allocated from ovpn_peer_new() via
ovpn_nl_peer_new_doit(), and freed through ovpn_peer_release_rcu() from RCU
callback processing. Observed access sites include ovpn_peer_remove(),
ovpn_socket_release(), ovpn_nl_peer_del_notify(), and unlock_ovpn().
Fix this by returning from the socket mismatch branch without putting the
peer. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: validate DFS referral PathConsumed
parse_dfs_referrals() validates that the response contains the fixed
referral entry array and, on for-next, the per-referral string offsets.
However, the response also contains a PathConsumed value that is later
used for DFS path parsing.
If a malformed response provides a PathConsumed value larger than the
search name, later DFS parsing can advance beyond the end of the path.
Validate PathConsumed against the search name length before storing it in
the parsed referral. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: reject optional IPTFS templates in outbound policies
syzbot reported a stack-out-of-bounds read in xfrm_state_find()
which flows from xfrm_tmpl_resolve_one().
Commit 3d776e31c841 ("xfrm: Reject optional tunnel/BEET mode
templates in outbound policies") disallowed optional tunnel and
BEET in outbound policies to prevent this. Later when IPTFS
added, it was not covered by that fix and can still trigger
the out-of-bounds read;
Extend the check to disallow optional IPTFS in outbound policies
as well. IPTFS should be identical to tunnel mode.
IN and FWD policies are not affected: xfrm_tmpl_resolve_one()
is only reachable via the outbound path.
Reproducer, before:
ip link add dummy0 type dummy
ip link set dummy0 up
ip addr add 10.1.1.1/24 dev dummy0
ip xfrm policy add src 10.1.1.1/32 dst 10.1.1.2/32 dir out tmpl
src fc00::dead:1 dst fc00::dead:2 proto esp reqid 1 mode iptfs
level use tmpl src fc00::dead:1 dst fc00::dead:2 proto esp reqid
2 mode transport
ping -W 1 -c 1 10.1.1.2
PING 10.1.1.2 (10.1.1.2) 56(84) bytes of data.
[ 64.168420] ==================================================================
[ 64.169977] BUG: KASAN: stack-out-of-bounds in __xfrm6_addr_hash+0x11e/0x170
[ 64.169977] Read of size 4 at addr ffff88800e1ffd20 by task ping/2844
[ 64.169977] CPU: 2 UID: 0 PID: 2844 Comm: ping Not tainted 7.1.0-rc7-00180-geb23b588430a #98 PREEMPT(full)
[ 64.169977] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[ 64.169977] Call Trace:
[ 64.169977] <TASK>
[ 64.169977] dump_stack_lvl+0x47/0x70
[ 64.169977] ? __xfrm6_addr_hash+0x11e/0x170
[ 64.169977] print_report+0x152/0x4b0
[ 64.169977] ? ksys_mmap_pgoff+0x6d/0xa0
[ 64.169977] ? entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 64.169977] ? rcu_read_unlock_sched+0xa/0x20
[ 64.169977] ? __virt_addr_valid+0x21b/0x230
[ 64.169977] ? __xfrm6_addr_hash+0x11e/0x170
[ 64.169977] kasan_report+0xa8/0xd0
[ 64.169977] ? __xfrm6_addr_hash+0x11e/0x170
[ 64.169977] __xfrm6_addr_hash+0x11e/0x170
[ 64.169977] __xfrm_dst_hash+0x24/0xc0
[ 64.169977] xfrm_state_find+0xa2d/0x2f90
[ 64.169977] ? __pfx_xfrm_state_find+0x10/0x10
[ 64.169977] ? __pfx_ftrace_graph_ret_addr+0x10/0x10
[ 64.169977] ? __pfx_ftrace_graph_ret_addr+0x10/0x10
[ 64.169977] xfrm_tmpl_resolve_one+0x210/0x570
[ 64.169977] ? __pfx_xfrm_tmpl_resolve_one+0x10/0x10
[ 64.169977] ? __pfx_stack_trace_consume_entry+0x10/0x10
[ 64.169977] ? kernel_text_address+0x5b/0x80
[ 64.169977] ? __kernel_text_address+0xe/0x30
[ 64.169977] ? unwind_get_return_address+0x5e/0x90
[ 64.169977] ? arch_stack_walk+0x8c/0xe0
[ 64.169977] xfrm_tmpl_resolve+0x130/0x200
[ 64.169977] ? __pfx_xfrm_tmpl_resolve+0x10/0x10
[ 64.169977] ? __pfx_xfrm_policy_inexact_lookup_rcu+0x10/0x10
[ 64.169977] ? __refcount_add_not_zero.constprop.0+0xb2/0x110
[ 64.169977] ? __pfx___refcount_add_not_zero.constprop.0+0x10/0x10
[ 64.169977] xfrm_resolve_and_create_bundle+0xd5/0x310
[ 64.169977] ? __pfx_xfrm_resolve_and_create_bundle+0x10/0x10
[ 64.169977] ? __pfx_xfrm_policy_lookup_bytype+0x10/0x10
[ 64.169977] ? __pfx_xfrm_policy_lookup_bytype+0x10/0x10
[ 64.169977] xfrm_lookup_with_ifid+0x3d8/0xb80
[ 64.169977] ? __pfx_xfrm_lookup_with_ifid+0x10/0x10
[ 64.169977] ? ip_route_output_key_hash+0xc6/0x110
[ 64.169977] ? kasan_save_track+0x10/0x30
[ 64.169977] xfrm_lookup_route+0x18/0xe0
[ 64.169977] ip4_datagram_release_cb+0x4c9/0x530
[ 64.169977] ? __pfx_ip4_datagram_release_cb+0x10/0x10
[ 64.169977] ? do_raw_spin_lock+0x71/0xc0
[ 64.169977] ? __pfx_do_raw_spin_lock+0x10/0x10
[ 64.169977] release_sock+0xb0/0x170
[ 64.169977] udp_connect+0x43/0x50
[ 64.169977] __sys_connect+0xa6/0x100
[ 64.169977] ? alloc_fd+0x2e9/0x300
[ 64.169977] ? __pfx___sys_connect+0x10/0x10
[ 64.169977] ? preempt_latency
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: virt_concat: fix use-after-free in mtd_virt_concat_destroy()
mtd_concat_destroy() frees item->concat so calling
mtd_virt_concat_put_mtd_devices(item->concat) after that leads to a
use-after-free.
Fix it by moving mtd_virt_concat_put_mtd_devices() before
mtd_concat_destroy(). |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: virt_concat: fix use-after-free in mtd_virt_concat_destroy_joins()
mtd_concat_destroy() frees item->concat so calling
mtd_virt_concat_put_mtd_devices(item->concat) leads to a use after free.
Fix this by moving mtd_virt_concat_put_mtd_devices() before
mtd_concat_destroy() |
| Improper Neutralization of Input During Web Page Generation (XSS or 'Cross-site Scripting') vulnerability in WatchGuard Fireware OS (Gateway Wireless Controller module) allows Stored XSS. |
| Improper Neutralization of Input During Web Page Generation (XSS or 'Cross-site Scripting') vulnerability in WatchGuard Fireware OS (Autotask Technology Integration module) allows Stored XSS. |
| Improper Neutralization of Input During Web Page Generation (XSS or 'Cross-site Scripting') vulnerability in WatchGuard Fireware OS (ConnectWise Technology Integration module) allows Stored XSS. |
| Improper Neutralization of Input During Web Page Generation (XSS or 'Cross-site Scripting') vulnerability in WatchGuard Fireware OS (Tigerpaw Technology Integration module) allows Stored XSS. |
| nanoid (Nano ID) before 5.1.6 contains an infinite loop in the customAlphabet and customRandom functions. When these functions are configured with a size of 0, the internal generation loop never satisfies its exit condition and spins indefinitely, hanging the calling thread. An application that passes an unvalidated, attacker-controlled size of 0 to these functions is exposed to a denial-of-service condition. |
| An Out-of-bounds Write vulnerability in WatchGuard Fireware OS's CLI could allow an authenticated privileged user to execute arbitrary code via a specially crafted CLI command. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: validate CP_GFX_SHADOW chunk size in CS pass1
Add a minimum-length check for the AMDGPU_CHUNK_ID_CP_GFX_SHADOW chunk in
amdgpu_cs_pass1(), matching the gate already present for the IB, FENCE and
BO_HANDLES chunk types.
The CP_GFX_SHADOW case previously shared a bare break with the dependency
and syncobj chunk types, which do not dereference a fixed-size struct. When
userspace submits this chunk with length_dw == 0, vmemdup_array_user() is
called with size 0 and returns ZERO_SIZE_PTR, which passes the IS_ERR()
check. amdgpu_cs_p2_shadow() then dereferences chunk->kdata as a struct
drm_amdgpu_cs_chunk_cp_gfx_shadow (reading shadow->flags), faulting on the
ZERO_SIZE_PTR and causing a NULL-pointer dereference.
This is reachable by an unprivileged process in the render group. Reject
undersized chunks with -EINVAL during pass1 so the bad submission is
rejected before pass2 ever dereferences the data.
(cherry picked from commit 7f61b2eef7415eccdb40850aca0de94211948657) |
| In the Linux kernel, the following vulnerability has been resolved:
usb: atm: ueagle-atm: reject descriptors that confuse probe and disconnect
uea_probe() distinguishes a pre-firmware device from a post-firmware one
using the USB id (UEA_IS_PREFIRM()), and stores a different object as the
interface data in each case: a 'struct completion' for a pre-firmware
device (to be waited on in .disconnect()), or a 'struct usbatm_data' for a
post-firmware one.
uea_disconnect() instead tells the two apart by the number of interfaces
of the active configuration (a pre-firmware device exposes a single
interface, ADI930 has 2 and eagle has 3), and casts the interface data
accordingly.
Because the two handlers use different criteria, a crafted device that
advertises a pre-firmware id together with a multi-interface descriptor
(or a post-firmware id with a single interface) makes them disagree: the
small 'struct completion' stored by uea_probe() is then passed to
usbatm_usb_disconnect(), which casts it to 'struct usbatm_data' and takes
instance->serialize, reading past the end of the allocation:
BUG: KASAN: slab-out-of-bounds in __mutex_lock+0x152a/0x1b80
Read of size 8 at addr ffff8880470e2c60 by task kworker/1:2/982
...
__mutex_lock+0x152a/0x1b80
usbatm_usb_disconnect+0x70/0x820
uea_disconnect+0x133/0x2c0
usb_unbind_interface+0x1dd/0x9e0
...
which belongs to the cache kmalloc-96 of size 96
The buggy address is located 0 bytes to the right of
allocated 96-byte region [ffff8880470e2c00, ffff8880470e2c60)
Reject such inconsistent descriptors in uea_probe() so that both handlers
always make the same pre/post-firmware decision. |
| In the Linux kernel, the following vulnerability has been resolved:
arm_mpam: guard MBWU state before adding it to garbage
__destroy_component_cfg() adds each RIS mbwu_state object to the MPAM
garbage list when destroying component configuration.
However, mbwu_state is allocated per RIS and only for RISes with MBWU
monitors. A component can therefore have comp->cfg allocated while some
RISes still have ris->mbwu_state set to NULL.
Passing a NULL mbwu_state to add_to_garbage() dereferences the NULL
pointer inside the macro.
Skip RISes that do not have an mbwu_state object before adding them to
the garbage list. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (corsair-cpro) Stop device IO before calling hid_hw_stop
Calling hid_hw_stop() does not stop the device IO.
This results in a race condition between hid_input_report() and the point
immediately following the execution of hid_device_io_start() within
the driver probe function. If the probe operation fails after "io start"
has been initiated, this race condition will result in a UAF vulnerability.
Fix the problem by calling hid_device_io_stop() before calling
hid_hw_stop(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix NULL pointer dereference in ath11k_hal_srng_access_begin
In ATH11K_QMI_EVENT_FW_READY, ATH11K_FLAG_REGISTERED is set
unconditionally even when ath11k_core_qmi_firmware_ready() fails.
This leaves the driver in an inconsistent state where
initialization is considered complete although the firmware ready
handling did not finish successfully. During the subsequent SSR,
the driver enters the restart path based on this incorrect state
and dereferences uninitialized srng members, resulting in a NULL
pointer dereference.
Call trace:
ath11k_hal_srng_access_begin+0xc/0x60 [ath11k] (P)
ath11k_ce_cleanup_pipes+0x17c/0x180 [ath11k]
ath11k_core_restart+0x40/0x168 [ath11k]
Fix this by:
- skipping firmware_ready if ATH11K_FLAG_REGISTERED is already set
- setting ATH11K_FLAG_REGISTERED only when firmware_ready succeeds
- setting ATH11K_FLAG_QMI_FAIL and aborting the FW_READY handling
on error
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.2.0.c2-00204-QCAMSLSWPLZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix ISM dc_lock deadlock during suspend
[Why]
System hang observed during suspend/resume while video is playing.
amdgpu_dm_ism_disable() is called under dc_lock and waits for ISM
delayed work via disable_delayed_work_sync(). The work handlers
themselves take dc_lock, producing an ABBA deadlock when a worker is
in flight at suspend time.
[How]
Split the disable path into two phases with opposite locking
contracts:
1. amdgpu_dm_ism_disable() -- quiesces workers, must NOT hold
dc_lock.
2. amdgpu_dm_ism_force_full_power() (new) -- drives the ISM FSM
back to FULL_POWER_RUNNING, must hold dc_lock. |
