| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tcpm: bound altmode_desc[] per iteration in svdm_consume_modes()
svdm_consume_modes() checks pmdata->altmodes against the array size once
before the loop over the count, but forgot to check the bound at every
point in the loop.
In the well-behaved SVDM discovery flow this is harmless because each of
at most SVID_DISCOVERY_MAX SVIDs contributes at most MODE_DISCOVERY_MAX
modes, exactly filling altmode_desc[ALTMODE_DISCOVERY_MAX]. But the
CMDT_RSP_ACK handler in tcpm_pd_svdm() does not correlate an incoming
ACK with any request the port actually sent. Once port->partner is set,
an unsolicited Discover Modes ACK is consumed unconditionally. A broken
or malicious port partner can therefore drive altmodes to
ALTMODE_DISCOVERY_MAX - 1 via the normal flow, and then send one extra
Discover Modes ACK with seven VDOs. Because the pre-loop check passes,
the loop could then writes up to five entries past altmode_desc[]. For
mode_data_prime the next field in struct tcpm_port is the
partner_altmode[] pointer array, which then receives partner-chosen
SVID/VDO bytes.
Move the bound check inside the loop so the array can never be indexed
past ALTMODE_DISCOVERY_MAX regardless of how many VDOs the partner
supplies or how the function was reached. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix amdgpu_hmm_range_get_pages
The notifier sequence must only be read once or otherwise we could work
with invalid pages.
While at it also fix the coding style, e.g. drop the pre-initialized
return value and use the common define for 2G range.
(cherry picked from commit c08972f555945cda57b0adb72272a37910153390) |
| In the Linux kernel, the following vulnerability has been resolved:
net: airoha: Add missing bits in airoha_qdma_cleanup_tx_queue()
Similar to airoha_qdma_cleanup_rx_queue(), reset DMA TX descriptors in
airoha_qdma_cleanup_tx_queue routine. Moreover, reset TX_DMA_IDX to
TX_CPU_IDX to notify the NIC the QDMA TX ring is empty. |
| In the Linux kernel, the following vulnerability has been resolved:
net: airoha: Do not read uninitialized fragment address in airoha_dev_xmit()
The transmit loop in airoha_dev_xmit() reads fragment address and length
during its final iteration, when the loop index equals
skb_shinfo(skb)->nr_frags, at which point the fragment data is
uninitialized. While these values are never consumed, the read itself is
unsafe and may trigger a page fault. Fix this by avoiding the fragment
read on the last iteration.
Additionally, move the skb pointer from the first to the last used packet
descriptor, so that airoha_qdma_tx_napi_poll() defers freeing the skb
until the final descriptor is processed. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: add wcid publish check in mt76_sta_add
Since mt7925_mac_sta_add publishes wcid, add publish check in mt76_sta_add
to avoid reinitializing the wcid->poll_list.
Found dev->sta_poll_list corruption when using mt7925 and 7.1-rc4.
According to the corruption information, prev->next was changed to itself.
wlan0: disconnect from AP 90:fb:5d:94:8b:e3 for new auth to 90:fb:5d:94:8b:e2
wlan0: authenticate with 90:fb:5d:94:8b:e2 (local address=84:9e:56:9c:7e:6b)
wlan0: send auth to 90:fb:5d:94:8b:e2 (try 1/3)
slab kmalloc-8k start ffff8c80958a6000 pointer offset 4160 size 8192
list_add corruption. prev->next should be next (ffff8c808a7488f8), but was ffff8c80958a7040. (prev=ffff8c80958a7040).
mt76_wcid_add_poll+0x95/0xd0 [mt76]
mt7925_mac_add_txs.part.0+0xa5/0xe0 [mt7925_common]
mt7925_rx_check+0xa7/0xc0 [mt7925_common]
mt76_dma_rx_poll+0x50d/0x790 [mt76]
mt792x_poll_rx+0x52/0xe0 [mt792x_lib] |
| In the Linux kernel, the following vulnerability has been resolved:
gcov: use atomic counter updates to fix concurrent access crashes
GCC's GCOV instrumentation can merge global branch counters with loop
induction variables as an optimization. In inflate_fast(), the inner copy
loops get transformed so that the GCOV counter value is loaded multiple
times to compute the loop base address, start index, and end bound. Since
GCOV counters are global (not per-CPU), concurrent execution on different
CPUs causes the counter to change between loads, producing inconsistent
values and out-of-bounds memory writes.
The crash manifests during IPComp (IP Payload Compression) processing when
inflate_fast() runs concurrently on multiple CPUs:
BUG: unable to handle page fault for address: ffffd0a3c0902ffa
RIP: inflate_fast+1431
Call Trace:
zlib_inflate
__deflate_decompress
crypto_comp_decompress
ipcomp_decompress [xfrm_ipcomp]
ipcomp_input [xfrm_ipcomp]
xfrm_input
At the crash point, the compiler generated three loads from the same
global GCOV counter (__gcov0.inflate_fast+216) to compute base, start, and
end for an indexed loop. Another CPU modified the counter between loads,
making the values inconsistent - the write went 3.4 MB past a 65 KB
buffer.
Add -fprofile-update=prefer-atomic to CFLAGS_GCOV at the global level in
the top-level Makefile, guarded by a try-run compile test. The test
compiles a minimal program with and without -fprofile-update=prefer-atomic
using the full KBUILD_CFLAGS, then compares undefined symbols in the
resulting object files. If prefer-atomic introduces new undefined
references (such as __atomic_fetch_add_8 on i386 or __aarch64_ldadd8_relax
on arm64 with outline-atomics), the flag is not added -- the kernel does
not link against libatomic.
On architectures where GCC inlines 64-bit atomic counter updates (x86_64,
s390, ...) the test passes and the flag is enabled, preventing the
compiler from merging counters with loop induction variables and fixing
the observed concurrent-access crash.
On architectures where the flag would introduce libatomic dependencies, it
is silently omitted and behaviour is no worse than before this patch.
Move the CFLAGS_GCOV block from its original position (before the arch
Makefile include) to after the core KBUILD_CFLAGS assignments but before
the scripts/Makefile.gcc-plugins include. This placement ensures the
try-run test sees arch-specific flags (-m32, -march=,
-mno-outline-atomics) while avoiding GCC plugin flags (-fplugin=) that
would break the test on clean builds when plugin shared objects do not yet
exist. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: read COW data with the original inode during atomic write
When updating an atomic-write file, f2fs_write_begin() may read the
previously written data back from the COW inode:
prepare_atomic_write_begin() locates the block in the COW inode and sets
use_cow, and the read bio is then built with the COW inode:
f2fs_submit_page_read(use_cow ? F2FS_I(inode)->cow_inode : inode,
...);
and f2fs_grab_read_bio() decides whether to schedule fs-layer decryption
(STEP_DECRYPT) for the bio based on that inode via
fscrypt_inode_uses_fs_layer_crypto().
However, the folio being filled belongs to the original inode
(folio->mapping->host == inode), and the data stored in the COW block was
encrypted (or left as plaintext) using the original inode's context, not
the COW inode's -- see f2fs_encrypt_one_page(), which keys off
fio->page->mapping->host. fscrypt_decrypt_pagecache_blocks() likewise
operates on folio->mapping->host.
The COW inode is created as a tmpfile in the parent directory and inherits
its encryption policy from there. With test_dummy_encryption the newly
created COW inode gets the dummy policy and becomes encrypted, while a
pre-existing regular file -- created before the policy applied, e.g.
already present in the on-disk image -- stays unencrypted. The read
path then sets STEP_DECRYPT based on the encrypted COW inode and calls
fscrypt_decrypt_pagecache_blocks() on a folio whose host (the unencrypted
original inode) has a NULL ->i_crypt_info, dereferencing it:
Oops: general protection fault, probably for non-canonical address ...
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
RIP: 0010:fscrypt_decrypt_pagecache_blocks+0xa0/0x310
Workqueue: f2fs_post_read_wq f2fs_post_read_work
Call Trace:
fscrypt_decrypt_bio+0x1eb/0x340
f2fs_post_read_work+0xba/0x140
process_one_work+0x91c/0x1a40
worker_thread+0x677/0xe90
kthread+0x2bc/0x3a0
The COW inode is only needed to locate the on-disk block, and that block
address is already resolved into @blkaddr by prepare_atomic_write_begin()
via __find_data_block(cow_inode, ...); f2fs_submit_page_read() then reads
from that physical @blkaddr directly, so the inode argument only selects
the post-read crypto context, not which block is fetched. Reading with
@inode therefore returns the same (latest, not-yet-committed) COW data,
while making both the fs-layer decryption decision and the inline crypto
path use the correct (original inode's) key.
With the COW inode no longer used at the read site, the use_cow flag has no
remaining consumer; drop it from f2fs_write_begin() and
prepare_atomic_write_begin(). |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: omap2: fix use-after-free in omapfb_mmap
omapfb_mmap() has a race condition with OMAPFB_SETUP_PLANE ioctl that
can lead to use-after-free:
The fb_mmap() entry point holds mm_lock but not lock (fb_info->lock),
while ioctl handlers like OMAPFB_SETUP_PLANE hold lock but not mm_lock.
This allows concurrent execution.
In omapfb_mmap():
1. rg = omapfb_get_mem_region(ofbi->region); // Get old region ref
2. start = omapfb_get_region_paddr(ofbi); // Read from NEW region
3. len = fix->smem_len; // Read from NEW region
4. vm_iomap_memory(vma, start, len); // Map NEW region memory
5. atomic_inc(&rg->map_count); // Increment OLD region!
Concurrently, OMAPFB_SETUP_PLANE can:
- Reassign ofbi->region = new_rg
- Update fix->smem_len
- OMAPFB_SETUP_MEM then checks NEW region's map_count (0!) and frees it
This leaves userspace with a mapping to freed physical memory.
The fix is to read all required values (start, len) from the same
region reference (rg) that will have its map_count incremented,
preventing the region from being freed while still mapped. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: always recover the gpu
Previously, in case there was no more work to do, recover worker
wouldn't trigger recovery and would instead rely on the gpu going to
sleep and then resuming when more work is submitted.
Recover_worker will first increment the fence of the hung ring so, if
there's only one job submitted to a ring and that causes an hang, it
will early out.
There's no guarantee that the gpu will suspend and resume before more
work is submitted and if the gpu is in a hung state it will stay in that
state and probably trigger a timeout again.
Just stop checking and always recover the gpu.
Patchwork: https://patchwork.freedesktop.org/patch/704066/ |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix fsck inconsistency caused by incorrect nat_entry flag usage
f2fs_need_dentry_mark() reads nat_entry flags without mutual exclusion
with the checkpoint path, which can result in an incorrect inode block
marking state. The scenario is as follows:
create & write & fsync 'file A' write checkpoint
- f2fs_do_sync_file // inline inode
- f2fs_write_inode // inode folio is dirty
- f2fs_write_checkpoint
- f2fs_flush_merged_writes
- f2fs_sync_node_pages
- f2fs_fsync_node_pages // no dirty node
- f2fs_need_inode_block_update // return true
- f2fs_fsync_node_pages // inode dirtied
- f2fs_need_dentry_mark //return true
- f2fs_flush_nat_entries
- f2fs_write_checkpoint end
- __write_node_folio // inode with DENT_BIT_SHIFT set
SPO, "fsck --dry-run" find inode has already checkpointed but still
with DENT_BIT_SHIFT set
The state observed by f2fs_need_dentry_mark() can differ from the state
observed in __write_node_folio() after acquiring sbi->node_write. The
root cause is that the semantics of IS_CHECKPOINTED and
HAS_FSYNCED_INODE are only guaranteed after the checkpoint write has
fully completed.
This patch moves set_dentry_mark() into __write_node_folio() and
protects it with the sbi->node_write lock. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix out-of-bounds read in dp_get_eq_aux_rd_interval()
[Why & How]
The aux_rd_interval array in struct dc_lttpr_caps is declared with
MAX_REPEATER_CNT - 1 (7) elements, indexed 0..6. However, the offset
parameter passed to dp_get_eq_aux_rd_interval() can be as large as
MAX_REPEATER_CNT (8) when a sink reports 8 LTTPR repeaters via DPCD.
This leads to an out-of-bounds read of aux_rd_interval[7] when offset
is 8.
Fix this by growing aux_rd_interval to MAX_REPEATER_CNT elements to
accommodate the full range of valid repeater counts defined by the DP
spec.
(cherry picked from commit a55a458a8df37a65ffda5cf721d554a8f74f6b04) |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/napi: cap busy_poll_to 10 msec
Currently there's no cap on the maximum amount of time that napi is
allowed to poll if no events are found, which can lead to kernel
complaints on a task being stuck as there's no conditional rescheduling
done within that loop.
Just cap it to 10 msec in total, that's already way above any kind of
sane value that will reap any benefits, yet low enough that it's
nowhere near being able to trigger preemption complaints. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921: Place upper limit on station AID
Any station configured with an AID over 20 causes a firmware crash.
This situation occurred in our testing using an AP interface on 7922
hardware, with a modified hostapd, sourced from Mediatek's OpenWRT
feeds.
In stock hostapd, station AIDs begin counting at 1, and this
configuration is prevented with an upper limit on associated stations.
However, the modified hostapd began allocation at 65, which caused the
firmware to crash. This fix does not allow these AIDs to work, but will
prevent the firmware crash.
This crash was only seen on IFTYPE_AP interfaces, and the fix does not
appear to have an effect on IFTYPE_STATION behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Avoid NULL dereference in dc_dmub_srv error paths
In dc_dmub_srv_log_diagnostic_data() and
dc_dmub_srv_enable_dpia_trace().
Both functions check:
if (!dc_dmub_srv || !dc_dmub_srv->dmub)
and then call DC_LOG_ERROR() inside that block.
DC_LOG_ERROR() uses dc_dmub_srv->ctx internally. So if
dc_dmub_srv is NULL, the logging itself can dereference a
NULL pointer and cause a crash.
Fix this by splitting the checks.
First check if dc_dmub_srv is NULL and return immediately.
Then check dc_dmub_srv->dmub and log the error only when
dc_dmub_srv is valid.
Fixes the below:
../display/dc/dc_dmub_srv.c:962 dc_dmub_srv_log_diagnostic_data() error: we previously assumed 'dc_dmub_srv' could be null (see line 961)
../display/dc/dc_dmub_srv.c:1167 dc_dmub_srv_enable_dpia_trace() error: we previously assumed 'dc_dmub_srv' could be null (see line 1166) |
| In the Linux kernel, the following vulnerability has been resolved:
net: mana: Guard mana_remove against double invocation
If PM resume fails (e.g., mana_attach() returns an error), mana_probe()
calls mana_remove(), which tears down the device and sets
gd->gdma_context = NULL and gd->driver_data = NULL.
However, a failed resume callback does not automatically unbind the
driver. When the device is eventually unbound, mana_remove() is invoked
a second time. Without a NULL check, it dereferences gc->dev with
gc == NULL, causing a kernel panic.
Add an early return if gdma_context or driver_data is NULL so the second
invocation is harmless. Move the dev = gc->dev assignment after the
guard so it cannot dereference NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phonet: do not BUG_ON() in pn_socket_autobind() on failed bind
syzbot reported a kernel BUG triggered from pn_socket_sendmsg() via
pn_socket_autobind():
kernel BUG at net/phonet/socket.c:213!
RIP: 0010:pn_socket_autobind net/phonet/socket.c:213 [inline]
RIP: 0010:pn_socket_sendmsg+0x240/0x250 net/phonet/socket.c:421
Call Trace:
sock_sendmsg_nosec+0x112/0x150 net/socket.c:797
__sock_sendmsg net/socket.c:812 [inline]
__sys_sendto+0x402/0x590 net/socket.c:2280
...
pn_socket_autobind() calls pn_socket_bind() with port 0 and, on
-EINVAL, assumes the socket was already bound and asserts that the
port is non-zero:
err = pn_socket_bind(sock, ..., sizeof(struct sockaddr_pn));
if (err != -EINVAL)
return err;
BUG_ON(!pn_port(pn_sk(sock->sk)->sobject));
return 0; /* socket was already bound */
However pn_socket_bind() also returns -EINVAL when sk->sk_state is not
TCP_CLOSE, even when the socket has never been bound and pn_port() is
still 0. In that case the BUG_ON() fires and panics the kernel from a
user-triggerable path.
Treat the "bind returned -EINVAL but pn_port() is still 0" case as a
regular error and propagate -EINVAL to the caller instead of crashing.
Existing callers already translate a non-zero return from
pn_socket_autobind() into -ENOBUFS/-EAGAIN, so returning -EINVAL here
only changes behaviour from panic to a normal errno. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Wrap DCN32 phantom-plane allocation in DC_RUN_WITH_PREEMPTION_ENABLED
[Why]
dcn32_validate_bandwidth() wraps dcn32_internal_validate_bw() with
DC_FP_START()/DC_FP_END(). In x86 non-RT, DC_FP_START takes fpregs_lock(),
which disables local softirqs.
The DML1 path through dcn32_enable_phantom_plane() calls kvzalloc() to
allocate ~335 KiB for dc_plane_state. This triggers the vmalloc path,
which calls BUG_ON(in_interrupt()) because it's invoked within the
FPU-enabled (softirq disabled) region, leading to a kernel crash.
[How]
Wrap the dc_state_create_phantom_plane() call with the
DC_RUN_WITH_PREEMPTION_ENABLED() macro to allow preemption during
this memory allocation.
(cherry picked from commit 885ccbef7b94a8b38f69c4211c679021aa27ad11) |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: only release the dirty pages io tree after successful writes
[WARNING]
With extra warning on dirty extent buffers at umount (aka, the next
patch in the series), test case generic/388 can trigger the following
warning about dirty extent buffers at unmount time:
BTRFS critical (device dm-2 state E): emergency shutdown
BTRFS error (device dm-2 state E): error while writing out transaction: -30
BTRFS warning (device dm-2 state E): Skipping commit of aborted transaction.
BTRFS error (device dm-2 state EA): Transaction 9 aborted (error -30)
BTRFS: error (device dm-2 state EA) in cleanup_transaction:2068: errno=-30 Readonly filesystem
BTRFS info (device dm-2 state EA): forced readonly
BTRFS info (device dm-2 state EA): last unmount of filesystem 4fbf2e15-f941-49a0-bc7c-716315d2777c
------------[ cut here ]------------
WARNING: disk-io.c:3311 at invalidate_and_check_btree_folios+0xfd/0x1ca [btrfs], CPU#8: umount/914368
CPU: 8 UID: 0 PID: 914368 Comm: umount Tainted: G OE 7.1.0-rc1-custom+ #372 PREEMPT(full) 2de38db8d1deae71fde295430a0ff3ab98ccf596
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS unknown 02/02/2022
RIP: 0010:invalidate_and_check_btree_folios+0xfd/0x1ca [btrfs]
Call Trace:
<TASK>
close_ctree+0x52e/0x574 [btrfs d2f0b1cd330d1287e7a9919d112eadfc0e914efd]
generic_shutdown_super+0x89/0x1a0
kill_anon_super+0x16/0x40
btrfs_kill_super+0x16/0x20 [btrfs d2f0b1cd330d1287e7a9919d112eadfc0e914efd]
deactivate_locked_super+0x2d/0xb0
cleanup_mnt+0xdc/0x140
task_work_run+0x5a/0xa0
exit_to_user_mode_loop+0x123/0x4b0
do_syscall_64+0x243/0x7c0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
---[ end trace 0000000000000000 ]---
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30539776 owner 9 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30621696 owner 257 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30638080 owner 258 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30654464 owner 7 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30703616 owner 2 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30720000 owner 10 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30736384 owner 4 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30752768 owner 11 gen 9 refs 2 flags 0x7
I'm using a stripped down version, which seems to trigger the warning
more reliably:
_fsstress_pid=""
workload()
{
dmesg -C
mkfs.btrfs -f -K $dev > /dev/null
echo 1 > /sys/kernel/debug/clear_warn_once
mount $dev $mnt
$fsstress -w -n 1024 -p 4 -d $mnt &
_fsstress_pid=$!
sleep 0
$godown $mnt
pkill --echo -PIPE fsstress > /dev/null
wait $_fsstress_pid
unset _fsstress_pid
umount $mnt
if dmesg | grep -q "WARNING"; then
fail
fi
}
for (( i = 0; i < $runtime; i++ )); do
echo "=== $i/$runtime ==="
workload
done
[CAUSE]
Inside btrfs_write_and_wait_transaction(), we first try to write all
dirty ebs, then wait for them to finish.
After that we call btrfs_extent_io_tree_release() to free all
extent states from dirty_pages io tree.
However if we hit an error from btrfs_write_marked_extent(), then we
still call btrfs_extent_io_tree_release() to clear that dirty_pages io
tree, which may contain dirty records that we haven't yet submitted.
Furthermore, the later transaction cleanup path will utilize that
dirty_pages io tree to properly cleanup those dirty ebs, but since it's
already empty, no dirty ebs are properly cleaned up, thus will later
trigger the warnings inside invalidate_btree_folios().
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Take the SRCU lock for page table walks in fault injection and AT emulation
walk_s1() and kvm_walk_nested_s2() expect to be called while holding
kvm->srcu to guard against memslot changes. While this is generally
the case, __kvm_at_s12() and __kvm_find_s1_desc_level() call into the
respective walkers without taking kvm->srcu.
Fix by acquiring kvm->srcu prior to the table walk in both instances. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: fix use-after-free on sbi->sync_decompress
z_erofs_decompress_kickoff() can race with filesystem unmount, causing
a use-after-free on sbi->sync_decompress.
When I/O completes, z_erofs_endio() calls z_erofs_decompress_kickoff()
to queue z_erofs_decompressqueue_work() asynchronously. Then, after all
folios are unlocked, unmount workflow can proceed and sbi will be freed
before accessing to sbi->sync_decompress.
Thread (unmount) I/O completion kworker
queue_work
z_erofs_decompressqueue_work
(all folios are unlocked)
cleanup_mnt
..
erofs_kill_sb
erofs_sb_free
kfree(sbi)
access sbi->sync_decompress // UAF!! |
